Same.
Self proclaimed Builder Of Badassery.
Buy it, Break it, Build it BETTER.
"Since 2004"
Same.
Self proclaimed Builder Of Badassery.
Buy it, Break it, Build it BETTER.
"Since 2004"
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
New gaskets or re-use old? (I think I know the answer) LOL
Loud, have you torn into yours yet?
Neil
2003 Mercury Marauder - DBP/DC
2003 Mercury Marauder - BLK/DC
2003 Mercury Marauder - SB/LF
2004 Mercury Marauder - DTR/LF
1964 Mercury Marauder - BLK/BLK
New gaskets Bubs. Usually in stock at Ford for like $2.00 each. I never could understand why so cheap, but chose not to question..
Self proclaimed Builder Of Badassery.
Buy it, Break it, Build it BETTER.
"Since 2004"
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
It's all done, shifts are nice and tightened up and reverse engages much faster. Took ten quarts to fill it back up, didn't drain the torque convertor.Loud, have you torn into yours yet?
^^+1^^New gaskets Bubs. Usually in stock at Ford for like $2.00 each. I never could understand why so cheap, but chose not to question..
2004 Black Marauder: #2237 Born on 4/1/2004
Eaton Swapped and a bunch of other goodies!
I knew the answer. I was going to tear the car apart today but will order gaskets Tuesday instead. Instead of rushing into it I worked on tagalong's car today. Ol' Girl received newer plugs, belt and PCV out of my blue....... gotta recycle!
Jmod next week.
Loud did you remove the springs?
Neil
2003 Mercury Marauder - DBP/DC
2003 Mercury Marauder - BLK/DC
2003 Mercury Marauder - SB/LF
2004 Mercury Marauder - DTR/LF
1964 Mercury Marauder - BLK/BLK
Jmod info from full thread: http://www.mercurymarauder.net/forum...ad.php?t=82460:
I ordered a Racing HP 4R70W Super Tuf seperator plate. It is thicker to prevent the cracking problem from being hammered by 1-2 actuator piston.
Cost:
$24 for separator plate (info below)
$4 for gasket 1 (from Nicco, my friendly local Ford parts dude)
$3 for gasket 2 (from Nicco, my friendly local Ford parts dude)
Filter Kit
10 qts ATF
This is a must do for performance car lovers and one of the cheapest mods!
Performance Automotive and Transmission Center
2134-A East Texas Street
Bossier City, LA 71111
318-742-7754
http://www.transmissioncenter.net/aode.htm
Part #8SP ($24) ordered 3, showed up at my door in 2 weeks.
Full thread: http://www.mercurymarauder.net/forum...ad.php?t=82460
WLB
BB#1) 1996 ImpalaSS - 16,500 miles - 100% stock
______________________________ ___________
BB#2) 2003 Marauder (300a) - 34k miles - Daily Driver
#2912 of 7093
Conceived 8/6/2002
Delivered 9/19/2002
Adopted 8/10/2011
Trilogy 242 - Self Installed 9/9/12 (0-60 5.5 sec)
Pioneer 6x8 Front
Legacy 600w 6x9 Rears
JL 6.5 SubWoofer
K&N CAI
Window tint 50% rear/35% front
FBM CHMSL with Strobe mod 7/1/12
DR Deep Aluminum Trans Pan
Sparta FOMOCO Racing 8.8 Girdle
Mo's Dyno Tune
Gorilla Nuts - The System
Ford Racing 4.10s, 31 spline Cobra carrier & axles 7/1/12
Powder Coat Axle Housing 7/1/12
CME HP Rear Control Arms & Watts Link 7/1/12
______________________________ ________________
Rex "SC Cheesehead" Weinbender 11-14-13
Ed "Baaad GN" Linthicum 8-6-2014
testing
Sent from my iPhone using Tapatalk
GOLD P74 INTERCEPTOR, A NEW PANTHER IN TOWN.
“When you can’t make them see the light, make them feel the heat.”
Ronald Regan
"The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."
Lt. Colonel Ralph Peters
“Be polite, be professional, but have a plan to kill everybody you meet.”
"I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
General James Mattis
Word of advise. Put teflon tape on the load studs before installing, and don't torque them down. They need to just hit the caps.
“When you can’t make them see the light, make them feel the heat.”
Ronald Regan
"The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."
Lt. Colonel Ralph Peters
“Be polite, be professional, but have a plan to kill everybody you meet.”
"I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
General James Mattis
There are currently 1 users browsing this thread. (0 members and 1 guests)