Page 1 of 2 12 LastLast
Results 1 to 15 of 17

Thread: DTC Code's P0351-P0358

  1. #1
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771

    DTC Code's P0351-P0358

    I know what they mean sort of but I been doing a little research and I have found it means a (possible ground fault a wire touching metal) on the circuit. Has anyone else here had this problem and what was the cause of it and what was the resolution.

    Here is what the codes are for.....

    P0351 Ignition Coil Primary A / Secondary Circuit Malfunction
    P0352 Ignition Coil Primary B / Secondary Circuit Malfunction
    P0353 Ignition Coil Primary C / Secondary Circuit Malfunction
    P0354 Ignition Coil Primary D / Secondary Circuit Malfunction
    P0355 Ignition Coil Primary E / Secondary Circuit Malfunction
    P0356 Ignition Coil Primary F / Secondary Circuit Malfunction
    P0357 Ignition Coil Primary G / Secondary Circuit Malfunction
    P0358 Ignition Coil Primary H / Secondary Circuit Malfunction


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

  2. #2
    Join Date
    Aug 2006
    Location
    Calgary,AB Canada
    Age
    53
    Posts
    617
    You betcha.I get everyone of these codes everytime I pin it through the shift points.This started after the S/c install.I think it is a fault with the alt. but I am not having any drivability issues and it is not misiing,I know that for sure.I was wondering if anyone else had ever had this problem.What brought this on for you?
    4;10's,JLT RAI,and Lidio's sct live wire,new air freshner,.......and now #153 Trilogy..377 hp and 400 lbs

  3. #3
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771
    Quote Originally Posted by chader View Post
    You betcha.I get everyone of these codes everytime I pin it through the shift points.This started after the S/c install.I think it is a fault with the alt. but I am not having any drivability issues and it is not misiing,I know that for sure.I was wondering if anyone else had ever had this problem.What brought this on for you?
    Happened 300 miles after my dyno tune. I have no drivability issues either read for codes a lil bit after clearing them then I got just 2 of them not all 8. Then one time all but 1. car doesnt miss and runs great. I have my Xcal2 hooked up to my laptop doing some data logging.

    Check out this http://dakotausa.com/vBulletin/showthread.php?t=17371
    Last edited by NATEHAWK; 04-05-2008 at 03:57 PM.


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

  4. #4
    Join Date
    Mar 2004
    Location
    NorthEast Kingdom of VT
    Age
    81
    Posts
    652
    maybe caused by low voltage when the alt cuts out at wot or sumpin

  5. #5
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771
    Thats a possibility I guess but the tune is proven over on many vehicles....But I know some vehicles perform differently from others....


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

  6. #6
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771
    Quote Originally Posted by chader View Post
    You betcha.I get everyone of these codes everytime I pin it through the shift points.This started after the S/c install.I think it is a fault with the alt. but I am not having any drivability issues and it is not misiing,I know that for sure.I was wondering if anyone else had ever had this problem.What brought this on for you?
    I read your thread on MCM and I think its just the fact when you nail it like I did I was going 120 or so. I have done just about everything in checking it out. I car didnt have a real aggressive tune prior now the tune is more aggressive and im using the smaller 3.2 pulley which im guessing when i spin it up more and really getting on it then I have the problem. Oh well the car is perfect and it so fun to drive its like going back in time fast lol...


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

  7. #7
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771
    Might be the gap of the plugs...Mine are at .030 originally they were at .032. Im going to re-gap them today and see what happens.


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

  8. #8
    Join Date
    Aug 2006
    Location
    Calgary,AB Canada
    Age
    53
    Posts
    617
    My codes started that way too.One at a time or only a few.But the harder I drove the more.In fact a couple of times I got a fuel pump circiut fault aswell.The one thing I have noticed is all coils and the fuel pump run off the same power supply,which comes directly from the alt.I did check plug gap already aswell.I agree it should not be a fault with the tune,because nobody else is having problems.I believe the alt. cut out is omitted whith Lidios tune.I have a couple of ideas of things to check when the roads clear up.1)if the alt is the cause(bad diode or some thing)if my battery is well charged and I unplug the alt.,take it for a run I maybe able to prove a fault with the alt.I have heard of this before.2)the one other thing I did at the same time the s/c'r was installed was replace the battery with a good used one.I have heard of batteries being at fault for stupid stuff like this?
    Let me know if you ever get any place with this.
    Chad
    4;10's,JLT RAI,and Lidio's sct live wire,new air freshner,.......and now #153 Trilogy..377 hp and 400 lbs

  9. #9
    Join Date
    Aug 2006
    Location
    Calgary,AB Canada
    Age
    53
    Posts
    617
    just FYI,I changed my plugs to Motorcraft.AGSF-22C/sp-505.I have driven the ***** out of it.I got P0358 twice put never put the CEL on.I have since cleared the code and continued to drive the ***** out of it and no more codes of any sort.This thing is even more fun when no CEL is on.
    4;10's,JLT RAI,and Lidio's sct live wire,new air freshner,.......and now #153 Trilogy..377 hp and 400 lbs

  10. #10
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771
    Cool man Im glad that helped you too. What kind of plugs did you have before you changed them and what were the gaps set at?


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

  11. #11
    Join Date
    Aug 2006
    Location
    Calgary,AB Canada
    Age
    53
    Posts
    617
    Quote Originally Posted by NATEHAWK View Post
    Cool man Im glad that helped you too. What kind of plugs did you have before you changed them and what were the gaps set at?
    Champion....the gaps all looked good at .30.Thank-you very much for your help.I was starting to feel out on my own on this one,till I talked to you.
    4;10's,JLT RAI,and Lidio's sct live wire,new air freshner,.......and now #153 Trilogy..377 hp and 400 lbs

  12. #12
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771
    Them damn chapion plugs..Boooo to champion Marauders like motorcraft.


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

  13. #13
    Join Date
    Mar 2007
    Location
    Hawaiian Islands
    Age
    60
    Posts
    1,943
    I was going to suggest looking at the gap and/or electrodes for "out of range" signs...

    What type of connectors are you guys using???

    With stock connectors, look for burning (dis-colored metal), I had two stockers that were burned and not conducting properly...

    With Granatelli's, look for arching (black marks), between the two ends of the clip...where the clip ends meet...Check, both top (coil side), and bottom (plug side)...

    Also look for torn plug boots...+ too much dailectic (spelling?) grease can cause it to ground...

    Mine (plugs) are set at .030...*NGK Tr6
    Good luck...

    ALOHA


    '03 A Build Date 8/02
    F.I.T. #6 ***RESURRECTED***
    *444 RWHP / 401 RWTQ
    *10 lbs. Boost
    *P1SC1 ProCharger
    *SCT Tuned *SCT Big Air 2400 MAF *BAP *GT 40 Fuel Pump *Modified FPDM *SSW Headers *MMX Drive Shaft *Metco Drive Shaft Loop *Metco Control Arms *T/A Stud Girdle w/ Diff Cover *Addco Sway Bars 3,500 Stall B/C Auto. Torque Converter *J-Mod *Wilwood 13" Big Brake Kit *Brembo Drilled/Slotted Rotors (Rear) *Widened Rims w/ 295 Nitto 555 *Autometer Wide Band A/F

    When I turn on my car...It returns the favor

  14. #14
    Join Date
    Aug 2006
    Location
    Calgary,AB Canada
    Age
    53
    Posts
    617
    [quote=Local Boy;614868]I was going to suggest looking at the gap and/or electrodes for "out of range" signs...

    What type of connectors are you guys using???

    With stock connectors, look for burning (dis-colored metal), I had two stockers that were burned and not conducting properly...

    With Granatelli's, look for arching (black marks), between the two ends of the clip...where the clip ends meet...Check, both top (coil side), and bottom (plug side)...

    Also look for torn plug boots...+ too much dailectic (spelling?) grease can cause it to ground...

    Mine (plugs) are set at .030...*NGK Tr6
    Good luck...

    ALOHA[/quote
    got stock COP's and they had all looked good.I was told that if you had a COP problemyou would have actual missfire codes,but not to sure and don't want to know either.Alll is working good now.Thanx to everyone who tried to help us.
    Chad
    4;10's,JLT RAI,and Lidio's sct live wire,new air freshner,.......and now #153 Trilogy..377 hp and 400 lbs

  15. #15
    Join Date
    Feb 2005
    Location
    DC MD Area
    Age
    43
    Posts
    1,771
    This problem is solved use motorcraft plugs and gap between 30 and 32.......


    2003 300A Black MM
    Quote Originally Posted by magindat View Post
    Modding a Marauder is a classy, time taking experience - like sipping fine aged spirits. It's meant to take your time, savor, and enjoy!!!!
    FRPP ALUMINATOR MOTOR 10:1
    BC AUTOMOTIVE TRANNY 2800 STALL
    TRILOGY S/C WITH POSI PERFORMANCE PORT
    STAINLESS WORKS LT HEADERS
    METCO REAR CONTROL ARMS AND WATTS LINK
    ADDCO FRONT & REAR SWAY BAR
    MONROE HD QUICK STRUTS FRONT
    QA1 ADJUSTABLE REAR SHOCKS
    EATON LIMTED SLIP DIFF:FORD RACING 4.10'S
    DUAL AEROMOTIVE 340LPH PUMPS, 40AMP BAP, WITH DUAL FPDM'S
    ZACKS BIG BRAKE SWAP w/ TCE SS LINES
    SCANGAUGE MONITORING....^....^....^
    ALL SECURIED WITH A VIPER SECURITY SYSTEM REMOTELY STARTED BY MY VIPER IPHONE APP

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. PCM Software codes demystified?
    By TripleTransAm in forum Community Discussion
    Replies: 16
    Last Post: 01-27-2008, 09:50 AM
  2. Question about Calibration Codes
    By Breadfan in forum Shop Talk
    Replies: 11
    Last Post: 08-24-2007, 08:13 AM
  3. Xcal2 and how to read codes?
    By ctrlraven in forum Shop Talk
    Replies: 20
    Last Post: 01-09-2007, 10:29 AM
  4. Trouble Codes on my Cougar's comp
    By RR|Suki in forum The Lounge
    Replies: 4
    Last Post: 07-27-2006, 10:20 AM
  5. Trouble Codes??
    By Marauderjack in forum Shop Talk
    Replies: 5
    Last Post: 03-24-2006, 03:25 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •