PDA

View Full Version : Wanted To Buy Coolant crossover tube for Eaton swap


SOSA03
03-21-2018, 09:59 AM
Hey I'm looking for a coolent crossover tube for Eaton swap, by any chance does anyone have an extra for sale????
Zack
03-21-2018, 10:13 AM
LOL. Needle in a haystack
03MERCMARAUDER
03-21-2018, 05:16 PM
Why not run a by pass delete setup from on3 or someone else?
Gerry24
03-21-2018, 07:52 PM
Why not run a by pass delete setup from on3 or someone else?



http://www.on3performance.com/shop/on-3-performance-coolant-crossover-delete-2-port/
decipha
07-11-2018, 08:15 AM
? about that delete kit, what all AN fittings are needed? looks like it only has 1 10an fitting? for the $69 option is surely has to include more than just that 1 10an fitting correct?
Turbov6Bryan
07-11-2018, 08:25 AM
It's 190.00 for the main kit. 69 gets you 3 -10 an fittings to finish off the kit.

Basically all those boxes to check off are options.
8UWITH6
07-11-2018, 09:59 AM
LOL I remember this feeling. Good luck!
Bad_S55
07-11-2018, 10:05 AM
Just do a COT delete. If you're REALLY dead set on having a tube, Jerry makes a stainless piece for Eaton swaps.
8UWITH6
07-11-2018, 10:08 AM
Just do a COT delete. If you're REALLY dead set on having a tube, Jerry makes a stainless piece for Eaton swaps.

I thought I heard Jerry is out of stock? Maybe not. I am sure he will chime in.
crownvic97
07-11-2018, 05:25 PM
I have the On3 kit, if I can figure it out anyone can. I recommend getting two rear fittings and the fittings and hose from On3
musclemerc
07-11-2018, 05:36 PM
Never cared for the COT delete kit.

The AN fittings feeding the heads neck down too small for my liking.

Jerrys kit is nice, no worry about lesser than OEM flow.
03MERCMARAUDER
07-11-2018, 05:43 PM
I thought I heard Jerry is out of stock? Maybe not. I am sure he will chime in.He is out. I am needing the same. Prob going to just get the on3 kit

Sent from my SM-G955U using Tapatalk
Themarauderguy
07-11-2018, 11:57 PM
Wow. Well the last set that I bought from him. he said he wasn't going to make any more. guess he was serious about that.
decipha
07-12-2018, 03:40 PM
Id rather not hack up my stock crossover just in case i need it for one of the other cars one day.

Any chance someone can post a finished photo of the on3 setup?
Ambitious1
07-12-2018, 04:15 PM
Post #37 will give you some idea:

https://www.mercurymarauder.net/forums/showthread.php?p=1408450
Turbov6Bryan
07-12-2018, 04:28 PM
Never cared for the COT delete kit.

The AN fittings feeding the heads neck down too small for my liking.

Jerrys kit is nice, no worry about lesser than OEM flow.

That is a valid point on the an fittings being a restriction!

I wonder if they out flow the next restriction, the open thermostat.

Uses a SBC stat ?
MOTOWN
07-12-2018, 05:37 PM
I had the On3 X-over delete kit on my YSI build and it never once had any overheating issues and you no longer have to burp the system with the X-over delete kit , the -10 fittings/lines aren't an issue , when all was said and done that combo made over 800RWHP , and yes it uses a small block Chevy stat.