Mach 1 chin spoiler for marauder

[Unknown]

Hello, first time poster here, I purchased my marauder about a month ago. I'm looking into purchasing a Mach 1 chin lip for it. Do you guy have any recommendations?
I see some that claim to be a bit longer to be flush with the mustang fender well. Is this a good route for the marauder or am I better off with the normal(short) version? Any brand or website recommendations? so far I'm looking at American muscle and LMR. Thanks for any advice.

[fastblackmerc]

Hello, first time poster here, I purchased my marauder about a month ago. I'm looking into purchasing a Mach 1 chin lip for it. Do you guy have any recommendations?
I see some that claim to be a bit longer to be flush with the mustang fender well. Is this a good route for the marauder or am I better off with the normal(short) version? Any brand or website recommendations? so far I'm looking at American muscle and LMR. Thanks for any advice.

Ebay for any place that sells Mustangs parts will have them.

This is the one most of us use:
https://www.ebay.com/itm/For-99-04-Mustang-Mach-1-Chin-Spoiler-CBR-Style-Front-Bumper-Lip-Kit-GT-SVT-PU/331538425427?epid=1253979678&hash=item4d313ae653:g:~R4AAOSw ~ehalHN2

I mount mine and the few I've installed with 1/4" plastic push rivets.

[Turbov6Bryan]

I buy all mine from American muscle, it's the matte finish like oem plastics

Others might be glossy and just don't look correct

[Unknown]

Thank you both for the response.
Would either of you say that the addition length that LMR claims to have is unnecessary for the marauder application?

Here is a video on it
https://youtu.be/yGj2cPeM0no

[NXSBOB]

Hello, first time poster here, I purchased my marauder about a month ago. I'm looking into purchasing a Mach 1 chin lip for it. Do you guy have any recommendations?
I see some that claim to be a bit longer to be flush with the mustang fender well. Is this a good route for the marauder or am I better off with the normal(short) version? Any brand or website recommendations? so far I'm looking at American muscle and LMR. Thanks for any advice.

This is a Genuine Ford (3R3Z-17626-AAA) on my car.

[Unknown]

This is a Genuine Ford (3R3Z-17626-AAA) on my car.

That looks really good! I think I would like the factory/shorter version so I can tuck the lip farther back under the bumper.

Anyone have any idea of American muscles version is the same size as the Ford OEM version?

[NATEHAWK]

Here's mine, ordered it from American Muscle. https://uploads.tapatalk-cdn.com/20180907/02f0e00ca7cac7e07defcdac1d13bc 92.png




Sent from my iPhone using Tapatalk

[Unknown]

[QUOTE=NATEHAWK;1564931]Here's mine, ordered it from American Muscle. https://uploads.tapatalk-cdn.com/20180907/02f0e00ca7cac7e07defcdac1d13bc 92.png




That looks really good I think Im going with American muscle! Thanks and Thanks to everyone for the help!

[Mr. Man]

IIRC it comes bent in half. Put it in the Sun for a while and it'll straighten out.

[NATEHAWK]

IIRC it comes bent in half. Put it in the Sun for a while and it'll straighten out.



What he said


Sent from my iPhone using Tapatalk

[Turbov6Bryan]

Thank you both for the response.
Would either of you say that the addition length that LMR claims to have is unnecessary for the marauder application?

Here is a video on it
https://youtu.be/yGj2cPeM0no

I think that the longer version is a longer lip so the Mach 1 looks like it has a beefier lip?

I've never purchased one, I don't think the marauder needs a huge lip under it.

Start in the middle and get the ends flush on each side

I put a bolt in the middle and cheat by using some of the existing bolt washers to hold the edge of the chin spoiler up, then use some of the existing holes and tighten it down
For the ends I use a 1/4 inch self tapping screw

[Mackdombles]

I cut mine in half, scooted them to the edges of the bumper, then angle cut the inside part with about a foot of gap in the center . Looks way better than one piece it's been for 2 years imo

[Maverick pro]

Ebay for any place that sells Mustangs parts will have them.

This is the one most of us use:
https://www.ebay.com/itm/For-99-04-Mustang-Mach-1-Chin-Spoiler-CBR-Style-Front-Bumper-Lip-Kit-GT-SVT-PU/331538425427?epid=1253979678&hash=item4d313ae653:g:~R4AAOSw ~ehalHN2

I mount mine and the few I've installed with 1/4" plastic push rivets.
Hey fastblackmerc...did you find the look to be as good as the factory one? Any pics of yours?

[1Marauder]

I cut mine in half, scooted them to the edges of the bumper, then angle cut the inside part with about a foot of gap in the center . Looks way better than one piece it's been for 2 years imo

Pictures or it didn't happen. Is this the Dave Letterman/Michael Strahan effect?

[fastblackmerc]

Hey fastblackmerc...did you find the look to be as good as the factory one? Any pics of yours?

It looks good. There is no "factory" one for the Marauder.