PCV grommet part number?

[a_d_a_m]

Anyone got one?
ordered a new PCV from Tasca but don’t like the way my OE grommet looks.

[justbob]

If in need they do have a regular PCV grommet in the help section at advance that fits our valve perfectly snug that I’ve used on Eaton swaps.


Sent from my iPhone using Tapatalk Pro

[a_d_a_m]

Thanks - will check it out.

[a_d_a_m]

Okay, bumping this.
Anyone know the part number for the grommet (or whatever it's called with the two smaller bolts) pictured here? I stole this pic from another thread. I swear I've been looking and I can't seem to figure this one out.

http://www.mercurymarauder.net/gallery/data/500/medium/MMPCV_006.jpg

[MyBlackBeasts]

https://www.tascaparts.com/oem-parts/ford-pcv-valve-grommet-f6az6a892ba?c=Zz1lbWlzc2lvbi1j b250cm9sJnM9Y3JhbmtjYXNlLXZlbn RpbGF0aW9uLXN5c3RlbSZsPTEmbj1B c3NlbWJsaWVzIFBhZ2UmYT1tZXJjdX J5Jm89bWFyYXVkZXImeT0yMDAzJnQ9 YmFzZSZlPTQtNmwtdjgtZ2Fz

[a_d_a_m]

I’m looking for the part that has the two bolts.
that isn’t it.

[MyBlackBeasts]

I believe when you remove the 2 bolts and pull the assembly out that you can swap in new rubber. I'm not positive, it was too long ago that I pulled mine. Check it and see (or are you missing the metal part too?).

[BLACK SUNSHINE]

On a similar topic, I'm having a hard time finding the rubber boot that connects the upper intake to the PCV tube. I started getting codes PO171 & 174 and after several checks for vacuum leaks I found that this connection was split where it transitions down to the smaller diameter plastic tube. Wasn't visible until you push on it and she opens up a nice crack. Any help will be much appreciated.
51213

[88LTDCV351]

That entire hose comes as one piece. I replaced mine. I think my tear was in the lower connector and not the top. I have the part number somewhere.


On a similar topic, I'm having a hard time finding the rubber boot that connects the upper intake to the PCV tube. I started getting codes PO171 & 174 and after several checks for vacuum leaks I found that this connection was split where it transitions down to the smaller diameter plastic tube. Wasn't visible until you push on it and she opens up a nice crack. Any help will be much appreciated.
51213

[88LTDCV351]

https://www.mercurymarauder.net/forums/showthread.php?103835-P0174-system-too-lean-bank-2/page3 part number 3W3Z6C324AA

[a_d_a_m]

That isn't the part I need.

[88LTDCV351]

Sorry, I was answering Black Sunshine's question.

[Fastbob]

Probably a little late...The Ford SnapOn EPC, (dealership electronic parts catalog), does not show a part number for the PCV valve retainer for the Marauder. It is not a grommet as the PCV valve on these engines is a quarter turn plastic unit held in place by the PCV valve retainer. The PCV valve turns a 1/4 tur to lock and unlock. Since the parts catalog does not list the retainer or it's retaining screws separately it is considered part of the cam cover. I did find the part number for the 2004 Mustang 4.6 DOHC engine PCV retainer was 2C5Z6A892AA and it might just work. It also uses a 1/4 turn PCV valve, but the PCV valve for the Mustang is different and may be of the heated style. Hope this helps.

Bob
Parts Manager
Lanterman Motors
Pratt, Kansas

[a_d_a_m]

Hope this helps. All of that information was helpful, and not late at all since the car is wrapped up until spring anyway.
Thank you.