remote transponders

[Mike]

Both of mine are not working. They were working one day, then nothing. No remote door un-locking, no trunk release. Any ideas? Thanks

[jgc61sr2002]

Both of mine are not working. They were working one day, then nothing. No remote door un-locking, no trunk release. Any ideas? Thanks

Check the batteries first.

[Mike]

Check the batteries first.

I still have to check them, but it surprised me that both went out at the same time. One of the transponders is fairly new. Is there a relay or something I can check?

[KillJoy]

I was going to suggest Fuse / Relay.

:D

KillJoy

[MACFORD88]

Try To Reset Them Have Both Controls Whit You.and Turn The Ingnition Switch On And Off 8 Times And You Will Hear The Door Locks Go Up And Doun Then All You Do Is Push Any Botton On Both Controls And Youer Done Good Luck.

[cyclopsram]

sounds like trying to solve a rubic's cube with blinder's on...

[Mike]

Try To Reset Them Have Both Controls Whit You.and Turn The Ingnition Switch On And Off 8 Times And You Will Hear The Door Locks Go Up And Doun Then All You Do Is Push Any Botton On Both Controls And Youer Done Good Luck.

Tried it and nothing happened :confused:

[Mike]

I was going to suggest Fuse / Relay.

:D

KillJoy

You know which one and where it might be located?

[KillJoy]

You know which one and where it might be located?


Yes, and yes. But, if I told you, then you would know.... and I would no longer "Special"

Dee Dee Dee!

KillJoy

PS - I gots no clue :D

[Zack]

Get out your owners manual.

BIG RED TRUCK

[Mike]

Get out your owners manual.

BIG RED TRUCK

yes sir! :bows:

[Mike]

Yes, and yes. But, if I told you, then you would know.... and I would no longer "Special"

Dee Dee Dee!

KillJoy

PS - I gots no clue :D

You'll ALWAYS be "special"!

[larryo340]

Tried it and nothing happened :confused:
what he was trying to say was to cycle the ignition switch from off to on(run,not cranking) eight times ending in run

At that time all the door locks should cycle up and down. If not turn the ignition back to off and try again, if nothing then this procedure won't work

Then press any button on one remote (locks should cycle, press button on other remote (locks should cycle)

Then turn key to off, open and close drivers door.

They should work.

Sometimes I have noticed that it may take a minute or two after procedure for them to work. Also the drivers door may have to be closed, or open I don't remember which

[Mike]

what he was trying to say was to cycle the ignition switch from off to on(run,not cranking) eight times ending in run

At that time all the door locks should cycle up and down. If not turn the ignition back to off and try again, if nothing then this procedure won't work

Then press any button on one remote (locks should cycle, press button on other remote (locks should cycle)

Then turn key to off, open and close drivers door.

They should work.

Sometimes I have noticed that it may take a minute or two after procedure for them to work. Also the drivers door may have to be closed, or open I don't remember which

Thanks, I will try again, but if it doesn't work then I'll have to look thru the big red book.

[RoyLPita]

Have you tried the keypad on the door to see if that works?

[MACFORD88]

Yes When Its On The On Position On The Quikly Push Any Botton On Both Remotes.thanks Larryo

[Mike]

I found it in the brb and I quote...

1) Make sure the anti-theft system is not armed or triggered

2) Turn the ignition switch from OFF to RUN 4 times within 3 seconds, ending in RUN. The locks will then lock and then unlock, confirming program mode has been entered.

3) Press any button on a keyless entry remote transmitter, and the door will lock and unlock to confirm that each remote transmitter has been programmed.

4) If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.

501-14-47

5) To exit program mode, wait 7.5 seconds.

Thanks to all who chimed in to help!!