Gauges

[DOOM]

Hey guys i was wondering if any of you had any pics of your aftermarket gauges you could post up for me? Im thinking about ordering a set and want to see what works for you guys. Im looking for a nice boost gauge for when i get my trilogy.

[Zack]

Order the Aeroforce Gauges

[Raudermaster]

http://www.supermotors.net/getfile/439998/fullsize/gauges-007.jpg
http://www.supermotors.net/getfile/439999/fullsize/gauges-008.jpg
http://www.supermotors.net/getfile/440000/fullsize/gauges-009.jpg
http://www.supermotors.net/getfile/440002/fullsize/gauges-011.jpg

[RF Overlord]

Im looking for a nice boost gauge for when i get my trilogy.The Trilogy kit comes with an AutoMeter boost gauge that matches the factory gauges.

[magindat]

Order the Aeroforce Gauges

period.

:bows:

[DOOM]

I was thinking about going with the aeroforce NEXUS gauges. Anyone here have them?

[Breadfan]

I have the autometer ultralite II's, they match the stock appearance during the day but have LED backlighting at night.

[DOOM]

The Trilogy kit comes with an AutoMeter boost gauge that matches the factory gauges.

I know it does but i would also like to have a REAL working oil pressure gauge. I dont need one for the volts I have a pioneer Z2 that gives me an accurate reading for that.

[Zack]

I know it does but i would also like to have a REAL working oil pressure gauge. I dont need one for the volts I have a pioneer Z2 that gives me an accurate reading for that.

Get the Aeroforce gauges with Oil Pressure kit.
Its a no brainer.

[DOOM]

Get the Aeroforce gauges with Oil Pressure kit.
Its a no brainer.

Are you referring to the ultralight 2's?

[Raudermaster]

UL2's are AutoMeter gauges.

[Eric91Z]

I was thinking about going with the aeroforce NEXUS gauges. Anyone here have them?

I think you mean the AutoMeter Nexus gauges. I am planning on going with them, too. The only person I know who has them is John (TooManyFords), but don't know if he has any pictures of them on here any more.

I am doing the Volt, Oil Pressure, and Tranny Temp gauges where the stock ones go (and the cigarette lighter). If you get the Volt gauge you have to get the 6401 controller. If you don't replace that you can go with the 6400 controller, but can't update the Volt gauge later as it doesn't work with the 6400 controller.

The Aeroforce is a good option too, but a little small for my liking. Nice thing with those is you can display 2 parameters per gauge and they plug directly in to the OBDII port for readings and power (except for the Oil Pressure).

[Breadfan]

If you want stock look the ultralite or utralite II's from Autometer will keep a stock appearance.

If you don't mind or don't want stock appearance then there are plenty of other choices, like the aeroforce ones mentioned above.

If you want accuracy well Autometer is in question. My ultralite II boost gauge reads differently than the ultralite 1 from Trilogy. I heard the oil pressure senders aren't very reliable either, luckily mine is still OK.

So yeah stock apperance go Autometer otherwise it sounds like there's better equipment to choose from.

[magindat]

(except for the Oil Pressure).
It's the same deal with Autometer. You need a sender...

[SILVERSURFER03]

oil press.sending unit will be needed for and gauge to make it accurate unless you run a hi press.line into car ......

but that could get ugly if it blows expecialy in the car messssssssssssssy

[2,4shofast]

I agree with the Auto Meter but I think the NV line would work best with the color set up of the stock gauges. I plan on doing the NV line gauges with Electronic hook ups so there is no worries about mechanical mishaps on the inside of the car...

[NATEHAWK]

You know what I'm running the Autometer Ultra lite 2's, I like the look of them and I have never had a problem with them. Oil Volt Boost.

[Eric91Z]

Is the Aeroforce setup the one that will allow you to run 2 of them so that you can have one in each slot where the stock ones are? And are they the same size to fit the stock holes?

If so, did they ever get all the bugs worked out so you can run the pair? And if I want to run oil pressure and tranny temp the only thing you need to add is the pressure sender for the oil pressure, correct?

[TooManyFords]

I was thinking about going with the aeroforce NEXUS gauges. Anyone here have them?
Yes, I have the complete set now. Speedo, Tach, all of them. I only have the Boost, Wideband, Fuel Pressure, Oil Pressure, Nitrous and Tranny temp hooked up right now. The tach, speedo, volts, water temp, fuel gauge, and fuel pressure will be mounted where the factory cluster goes. The remaining gauges will be the wideband and nitrous pressure on the post and the boost and tranny temp ub tge center console.

You'll just have to wait till I get the car back from tuning before I can show it off. If anyone is interested, I have the original Nexus control box (6400) for sale since upgrading to the 6401.

[red]

<html>I went with the Autometer Autolite replacement gauges. They look good to me:<table><tr><td align="center"></td><td align="center"><b>center</b></td><td align="center"><b>left</b></td><td align="center"><b>right</b></td></tr><tr><td align="center"><b>day</b></td><td align="center"><a href="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_light-front.jpg"><img height="288" width="384" src="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_light-front.jpg"></a></td><td align="center"><a href="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_light-left.jpg"><img height="288" width="384" src="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_light-left.jpg"></a></td><td align="center"><a href="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_light-right.jpg"><img height="288" width="384" src="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_light-right.jpg"></a></td></tr><tr><td align="center"><b>night</b></td><td align="center"><a href="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_dark-front.jpg"><img height="288" width="384" src="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_dark-front.jpg"></a></td><td align="center"><a href="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_dark-left.jpg"><img height="288" width="384" src="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_dark-left.jpg"></a></td><td align="center"><a href="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_dark-right.jpg"><img height="288" width="384" src="http://www.mercurymarauder.net/showcase/files/4/2/7/5/gauges_dark-right.jpg"></a></td></tr></table></html>

[magindat]

Looks nice. What are the two green llghts, Frank?

[red]

LEDs :lol:

[magindat]

LEDs :lol:

:eek: OMFG! You dork!!!! What are they FOR?! :rolleyes:

:beer:

[DOOM]

Thats what im talkin bout. Very nice setup, still looks factory.

[red]

Thats what im talkin bout. Very nice setup, still looks factory.Thanks. The gauges were relatively easy to install and I didn't lose the cigarette lighter (it's on the right side). When I need more gauges, I'm hoping to create a custom cluster where the '03 300a's have their clock, pending depth issues. If that fails, they'll go on the steering column.

[magindat]

Thanks. The gauges were relatively easy to install and I didn't lose the cigarette lighter (it's on the right side). When I need more gauges, I'm hoping to create a custom cluster where the '03 300a's have their clock, pending depth issues. If that fails, they'll go on the steering column.

Start looking for a steering column set up. I seem to remember a F150 top half fits. Wes knows. There's no depth on that panel unless you cut the sub plastic. Also, that matrix piece is designed to blow loose on airbag deployment so, you really shouldn't anchor it down in any way or add mass to it, IMO.

[red]

Start looking for a steering column set up. I seem to remember a F150 top half fits. Wes knows. There's no depth on that panel unless you cut the sub plastic. Also, that matrix piece is designed to blow loose on airbag deployment so, you really shouldn't anchor it down in any way or add mass to it, IMO.Thanks :), I wasn't aware of it's tie to the airbag system. On that note, I suppose I'll be using the steering column setup when the time comes.

[magindat]

Thanks :), I wasn't aware of it's tie to the airbag system. On that note, I suppose I'll be using the steering column setup when the time comes.

I originally thought Zack's Scangauge install in that spot unwise, however, it has not much if any more mass than the clock, so should still be safe as long as the cable isn't tied down hard.

Safety first....

Unfortunately, I've seen how that strip works first hand....

[red]

Unfortunately, I've seen how that strip works first hand.... Sorry to hear :(

[Joe Walsh]

Is this enough gauges?

I still have one more to add. (Intercooler inlet and outlet temperatures...whenever I install the Procharger...:o)

[DOOM]

DAMN!!! Do you need a drivers licence or pilots licence to operate that beast.

[hyvltge]

<html>I went with the Autometer Autolite replacement gauges. They look good to me:

Now that looks pimp! Did you just hole saw the opening for the third gauge and then drill a hole on the side for the lighter?

[Peace2Peep]

Just ordered the aeroforce gauges from the manufacturer...arrived at my dealership today! Pics to come Monday! Yeehaw!

[red]

Now that looks pimp! Did you just hole saw the opening for the third gauge and then drill a hole on the side for the lighter?

Thanks! Yup, that's it. Reinhart sells the gauge bezel, which puts the third gauge at the correct angle.

[Eric91Z]

Just ordered the aeroforce gauges from the manufacturer...arrived at my dealership today! Pics to come Monday! Yeehaw!

Can't wait to see the pictures. Did you get the "Marauder" setup with black trim ring, black background, green numbers, and says Marauder on it? And did you get the dual or single setup?

[TooManyFords]

Is this enough gauges?

LOL! That's like asking me if I have enough rear tire!

:D

[Joe Walsh]

LOL! That's like asking me if I have enough rear tire!

:D

Yep!

You, with the streamroller tires and SICK blower towering through the hood, and I, with the 747 instrument clusters, are NOT going to fool any RICERS into taking the bait.

[Embassy]

I read this on Wes' site:



Note: THe Gauge itself still has backlighting, but the numbers will not be back lit after the swap, but it is possible to swap the face of the stock gauge over to the functioning one. Check out Mercurymarauder.net for more details about this conversion!


Is there a tutorial on here about installing the OEM faces on the Autometer Ultralite II's?

Thanks.

[Peace2Peep]

I got the Marauder setup all right: black trim, black face, and green lettering. It does not say Marauder on the actual gauge but the screen shows the Godshead logo when you start it up...pics coming!

[Embassy]

I got the Marauder setup all right: black trim, black face, and green lettering. It does not say MArauder on the actual gauge but the screen shows the Godshead logo when you start it up...pics coming!

Looking forward to the pics.

[Peace2Peep]

I took pics tonight and will post them tomorrow...sorry I have to go to AZ early in the AM! They look great and I took enough pics for a brief install tutorial on install. BTW if you are considering gauges...definitely go for the Aeroforce...they are so perfect its almost sickening!

I know that they are expensive compared to the others out there, but to have an OEM replacement that looks totally at home in my car...PRICELESS!

[Peace2Peep]

http://www.mercurymarauder.net/forums/attachment.php?attachmentid=12 383&stc=1&d=1205392824http://www.mercurymarauder.net/forums/attachment.php?attachmentid=12 376&stc=1&d=1205392824

http://www.mercurymarauder.net/forums/attachment.php?attachmentid=12 377&stc=1&d=1205392824


http://www.mercurymarauder.net/forums/attachment.php?attachmentid=12 381&stc=1&d=1205392824






http://www.mercurymarauder.net/forums/attachment.php?attachmentid=12 382&stc=1&d=1205392824

[Peace2Peep]

How's That! I stinking love these...more pics and info to come..for now...gotta sleep!

[DOOM]

What nav unit do you have? I have a pioneer Z2, looks very similar.

[Peace2Peep]

I've got the Kenwood 8019 and its pretty good...I dont think the nav that Kenwood uses has as many POI or fine details as the Pioneer z2, but I do like having the high voltage rcas and two usb ports(one for ipod video and the other for anything else(thumb drives filled with music). But I actually comtrmplated both pretty hard before buying

[Taemian]

Doesn't the Trilogy come with a boost gauge already?

[Peace2Peep]

Yes it does and if you have the aeroforce it will display boost! You can sell the boost gauge they give you or add it if you insist and have it in the closest gauge hole with Dennis' conversion kit.

[Embassy]

You know what I'm running the Autometer Ultra lite 2's, I like the look of them and I have never had a problem with them. Oil Volt Boost.

Ditto.

http://www.supermotors.net/getfile/624326/fullsize/gauges-done2.jpg (http://www.supermotors.net/vehicles/registry/18556/63632)

http://www.supermotors.net/getfile/624328/fullsize/gauges-illuminated.jpg (http://www.supermotors.net/vehicles/registry/18556/63632)

Click on these pics to access the gallery.

[bigbillybbs]

AWSOME LOOKING you guys! :eek:
I love the way it looks with all three next to each other.
Do I have to hole saw for the third gauge? > Is there someone that sells them done.
If I attempt to ill screw something up!!?!! ( I am horrible with stuff like that) ???

[red]

Do I have to hole saw for the third gauge?
Yes, see the previous page.

Is there someone that sells them done.
No, but you can buy the gauge bezel rings yourself from Summit (part# is ATM-2234).

[bigbillybbs]

Yes, see the previous page.

No, but you can buy the gauge bezel rings yourself from Summit (part# is ATM-2234).


Thanks part # I love the way yours came out.. It looks awsome!!!!

I am going to install a trans temp gauge there to…