Spaz intake part deux...

[Blackened300a]

I finally got my intake back today from the welding shop. Took only over a month to do but the guy did it for free so I can't complain too much. He welded a 1/8" thick aluminum plate on the bottom. It seems much more solid and it sure as hell looks like it's welded to survive anything I throw at it. The test will be to see how it sounds and how it performs when re-installed on my car in a few weeks.

http://i32.photobucket.com/albums/d12/blackened300a/4bfbefdc.jpg
http://i32.photobucket.com/albums/d12/blackened300a/c1922c89.jpg
http://i32.photobucket.com/albums/d12/blackened300a/db6fb602.jpg
http://i32.photobucket.com/albums/d12/blackened300a/aeee2e13.jpg

[Glockafella]

The ported lower intake saga continues...good luck bro.

[SpartaPerformance]

The ported lower intake saga continues...good luck bro.

I saw the intake this evening and it looks great, I think it's going to hold up I just hope it's quiet unlike when you first got it.

[dohc324ci]

Cool Man keep us in the loop! NA SVT over at Corral.net is doing the same thing for cheaper....Good luck.

[DOOM]

Best of luck paul.

[SC Cheesehead]

+1

Will be interesting to see how it holds up and how it performs.

[Mr. Man]

Cool Man keep us in the loop! NA SVT over at Corral.net is doing the same thing for cheaper....Good luck.

Cheaper than free?

[ImpalaSlayer]

Cheaper than free?


i think he means the porting? :dunno:

[n00bkiller944]

Good luck! Keep us updated on how it works!!!

[ImpalaSlayer]

Paul, did he just weld this on top or did he cut off the old one?

[Blackened300a]

Paul, did he just weld this on top or did he cut off the old one?

Cut off the old one and replaced it with thicker aluminum.

[SpartaPerformance]

Cut off the old one and replaced it with thicker aluminum.

Cut it? Weren't all the welds broken? I think he just pulled it off. :run:

[RacerX]

Check out what this guy did!!! :D

http://www.svtperformance.com/forums/new-edge-cobras-51/660392-anatomy-psr-reconstructed.html

[Blackened300a]

Wow 1/4" plate? I hope that holds up.

[ImpalaSlayer]

Wow 1/4" plate? I hope that holds up.

i think that will do the trick lol

what a pos inside. damn did we get ripped or what>?

[Blackened300a]

what a pos inside. damn did we get ripped or what>?

Indeed. You think he would even offer a apology or some kind of response for his product failure.

[FordNut]

what a pos inside.

That's a surprise to me. My Terminator lower really looked good inside. Smoothed flow with epoxy in corners, all interior surfaces smoothed, porting/port matching looked perfect, injectors unshrouded.

He never did send my fitting back, though. Just quit replying to emails instead of continuing to promise "it'll go out this week".

[DTUB]

I heard from someone over at svtperformance that he went out of business. Anyone know the hole story??

[SpartaPerformance]

I heard from someone over at svtperformance that he went out of business. Anyone know the hole story??

I'm not familiar with whole story but if he went out of business it's not hard to figure out why. I remember Paul's agony in waiting months to get his intake...... everytime I'ld see him blah blah blah waaa waaa waaa. :D It finally showed up and boom....did it even last a few hundred miles Paul?? Anyway once in a while I would actually pay attention t what Paul was saying about Naz getting real sick. The quality just dropped after that. He should've refunded money and resumed after he got well again. My $0.02

[ImpalaSlayer]

That's a surprise to me. My Terminator lower really looked good inside. Smoothed flow with epoxy in corners, all interior surfaces smoothed, porting/port matching looked perfect, injectors unshrouded.

He never did send my fitting back, though. Just quit replying to emails instead of continuing to promise "it'll go out this week".


ive herd those cobra lowers from him are pretty good. guess ill never know

[Blackened300a]

I'm not familiar with whole story but if he went out of business it's not hard to figure out why. I remember Paul's agony in waiting months to get his intake...... everytime I'ld see him blah blah blah waaa waaa waaa. :D It finally showed up and boom....did it even last a few hundred miles Paul?? Anyway once in a while I would actually pay attention t what Paul was saying about Naz getting real sick. The quality just dropped after that. He should've refunded money and resumed after he got well again. My $0.02

Few hundred miles? Try less then a 100 miles. I made a few drives to cunningham and our dinner meets, then a few treks to my mothers house and then the idle surge started along with a rough idle. I pulled it off and there were 3 hairline cracks in the welds.
I dont think there was any quality in his design. Sick or not.
I have no doubt that it makes power, I felt it and proved it for myself with a few runs against my friends mustang, but his greed and poor choice in materials is what makes this intake a POS.

[FordNut]

ive herd those cobra lowers from him are pretty good. guess ill never know

I saw awhile back that somebody else at MF was doing the Cobra lowers now. I forget who it was.

[offroadkarter]

I saw awhile back that somebody else at MF was doing the Cobra lowers now. I forget who it was.



Wasn't posi, was it? IIRC he does lower porting as well as blower porting, and he does top notch work

[Vortech347]

The owners of this forum need to pay attention and close this section down. He has ripped off people in excess of thousands....

[Blackened300a]

The owners of this forum need to pay attention and close this section down. He has ripped off people in excess of thousands....

I think we should leave it up until he responds. Let his reputation be tarnished by this forum and threads.

[Vortech347]

Atleast take his site down so no one purchases anything.

[RacerX]

I believe a mod also said that as a vendor, he paid up for a certain amount of time to be listed. To honor contractual obligations and avoid needless repurcussions, best to leave it be. I think just about every Ford site knows about it...

[Phrog_gunner]

I guess than it's a bit crazy to mention the possibility of them using the remaining money left from his vendorship to go to the members who had to make repairs to fix the product???

[guspech750]

I think you fellas have it all wrong. Have you taken a look at their web site? And I quote,

"Nazty Performance is committed to provide the highest quality of services and we are customer focused! We provide you, the high performance consumer with the parts that you need! We take performance to the next level! When it comes to your cylinder head, intake manifolds or choosing a set of cams that is specific for your needs; Nazty Performance is your source!

Nazty Performance is owned by Carlos “Naz” Nazario and his Son “Naz Jr.” Naz’ is an US Army Chief Warrant Officer with 22 years of service and have been involved in the automotive performance scene for over 20 years, and have been involved with the Ford Modular engine family for about 10 years! Naz Jr. is dividing his school time, and while becoming a hardcore software engineer, he’s also working on his SAE Automotive Certification program. Together, they are Nazty Performance!

Nazty Performance is dedicated to 100% customer satisfaction! From the time you contact us for advice, place your order, shipping and following up its our goal to ensure you, the customer is 100% satisfied!

Sincerely,

Carlos “Naz” Nazario

Contact Us:
naz@naztyperformance.com





Gosh. After reading that I feel all warm and fuzzy inside. I am going to plance an order Thursday morning. Yeah right.:puke:

[Glockafella]

This is horrible to say but,...Did he die? I mean he vanished overnite and nobody has heard from him.

[Blackened300a]

This is horrible to say but,...Did he die? I mean he vanished overnite and nobody has heard from him.

I think he went into hiding. He would have a huge backlash if he popped up again.

[RacerX]

and while becoming a hardcore software engineer, he’s also working on his SAE Automotive Certification program.

OMG! Software engineers SUCK at hardware problems...
THAT explains a LOT! :D

[cougar9150]

OMG! Software engineers SUCK at hardware problems...
THAT explains a LOT! :D

LMAO at this one. It is absolutely true in my experience, never put a wrench in someones hands who punches a keyboard for a living.