Mods for 2010

[DOOM]

Im doing wilwoods within the next 2 weeks. (front)
2.8 upper pulley (polished of course) :coolman:
4# cobra crank pulley
wilwoods for the rear (summer)
31spline axles
detroit tru trac
get a few more parts polished (i have a few ideas) :D

Whatcha got on your list??? :beer:

[Pops]

Doomie is on my list!!!!:neener:

:director::burn::nos::drive:

[Bradley G]

I think he's Skeer'ed Pops!
Both cars will get the J-mod.
Marauder will get the same pulley as you picked, except anodized.
A GT fuel pump, hand held tuner, and a re-tune from BOC.
The LSE is going to get the heat fixed, then maybe some more goodies.

[FordNut]

CAI tube upgrade (actually that was a '09 mod but it's not back from ceramic coating yet), crankcase vacuum pump/PCV revision.

Figure out how to make a bolt-in roll bar that fits.

If I get a job, maybe a 9" rear end.

[breeze]

shes gotta go back in the shop AGAIN!!!..o/d light comes back on...but you already know Zacks Tune and CAI...

[Stranger in the Black Sedan]

Addco sway bars and home made rear boxed control arms

[kariamack]

Install my turbo system finally ..
Do all of my fuel system
crome my factory wheels
bear front brake kit
Powder coat and widen my 2nd set on factory wheel black
Install my audio system My pioneer Z2 and my Infinty componet set. Along with my 2 15 inch Kicker L7..
also my whole suspension: control arms front and rear sway bars


Ant thats about is ..

[dohc324ci]

Well first I must find a tuner that's competent...LOL then...

Replace Fuel Pressure Sensor
Accel COP
FRPP Shorty Headers w/14" Magnaflows Re-tune
Buy Jdennings002 - 4R75W Transmission and a 2800TC
Maybe - 31 Spline Axles w/LSD and 4.10s, DS w/DS loop
Replace BFGs

[james1986fox]

SW longtubes
Dyno tune
Intake spacer
Stewart emp water pump
125 shot nos (possibley)

[james1986fox]

SW longtubes
Dyno tune
Intake spacer
Stewart emp water pump
125 shot nos (possibley)

[LANDY]

well as for me:
a/f gauge
boost gauge
trans cooler gauge
tint headlights, tailights, windows, HID's
31 spline axles and diff..
cobra shortblock

[offroadking208]

a cat delete and 2.5 inch exhaust, not sure what mufflers yet, and MM tips. Install my MM airbox, 80mm MAF and 04 PI Zip tube, and install the Zack tune i have for the 80mm MAF

[imorb1994]

Hopefully get around to:
Underhood detail(valve covers and intake powder coating)
Fog light H.I.D's(not these cheap kits everbody is buying)
31 spline axles diff and new gears
Having tips set up the using the haggis method
S-55 treatment and spoiler, that should take up the whole year to get done:lol:

[Glockafella]

My mods will include

1.) Buying Powerball tickets

2.) Winning the Powerball

3.) Buying Carfixers MM.

4.) Installing all the same Mods Doom has

5.) Gold plating everything under the hood.

:beer::banana::burnout::D



No really I plan on a 200 Amp alternator, Steeda U/D Pulleys, New Battery, Brake Light Tint, Custom Dyno Tune.

[DEFYANT]

If I can swing a trip to see Lidio, watch out.

[ImpalaSlayer]

lets see, parts i have sitting in my garage:

a cobra long block in pieces

a set of 31 spline axles and cobra diff

a stage 3 steg blower with a 2.7 pulley

accufab single blade tb and plenum

a bunch of random parts ready to be powdercoated and polished

things awaiting my purchase:

widened wheels

sending the engine to the builder

things awaiting my creation:

custom snout idler

lord knows what else

[skyhigh]

4.10 gears and headers

[guspech750]

I guess anything I can afford:depress:

[SMOKE]

4.10 gears and headers


I guess anything I can afford:depress:

Right on both counts here :o...just sent in the last payment so lets see if a warchest builds and I'd say gears and headers, a lot of waxing and polishing and possibly the J-Mod in the spring when I wake her back up....

Best,
Jonathan

[Paul T. Casey]

Nothing (or at least that's what I'm telling my wife).

[Cheeseheadbob]

I will be doing the 2003 Mercury Marauder delete... I hope to sell the car this year.;)

[ctrlraven]

4.10 Gears
Ford Racing Diff
Larger diameter exhaust piping
New street tires all around (245/45-18 Front, 265 series on the rear)
Brake, Power Steering, Coolant and Trans flush

That's all I can think of right now.

[justbob]

Might change the brand of washing soap?:dunno:

[Dark_Knight7096]

only mod I plan on doing this year is the owner mod. That would consist of getting a better job so I can start making money again so I can ACTUALLY buy mods for the car. lol

I have an aluminum DOHC block .020" over in my garage as well as a set of DOHC heads, eventually I'll figure out something to do with them, lol.

[fastblackmerc]

Nothing (or at least that's what I'm telling my wife).

Same here.....

[Blackened300a]

Full exhaust, (Headers-tips)
New dyno tune
Try to keep my Spaz intake from cracking.

[2,4shofast]

My car is getting the rear emblem and door handles shaved, front emblem delete grille, cowl hood and new paint.
Finish up with my stereo install with misc odds and ends that have been bothering me and put some monitors in the headrests.
Replace all of my brakes and upgrade the front to the Baer kit, watts link and control arms need to be purchased and installed as well.
Fix my damn exhaust leak off the driver side block flange:argue: Start the savings fund for the S/C

I think I need another job however :(

[FW_Linc/Merc]

Nightshaded taillighs. I need a left one since I screwed up my spare set polishing them too much.

Badgeless grille if I get around to it.

[BruteForce]

Paint job this year. No really... this time I mean it.

[Vortex]

New set of back tires, new battery and a coolant system flush.

[Pops]

My car is getting the rear emblem and door handles shaved, front emblem delete grille, cowl hood and new paint.
Finish up with my stereo install with misc odds and ends that have been bothering me and put some monitors in the headrests.
Replace all of my brakes and upgrade the front to the Baer kit, watts link and control arms need to be purchased and installed as well.
Fix my damn exhaust leak off the driver side block flange:argue: Start the savings fund for the S/C

I think I need another job however :(

If you are going to drag race you might want to re consider the shaved door handles. The rules state that you have to have external handles. If they notice you will not be allowed to run! Ask how I know about it?:(

[Glenn]

Not one person has stated that these mods are for more GO at the track. What is the purpose of spending all this money if you don't also have a goal at the track for your performance improvements. Are all you guys Street Racers or just like the extra power to say you have it?

Glenn Ford :flamer:

[Pops]

Not one person has stated that these mods are for more GO at the track. What is the purpose of spending all this money if you don't also have a goal at the track for your performance improvements. Are all you guys Street Racers or just like the extra power to say you have it?

Glenn Ford :flamer:

So Glenn what do you think my smiley guys are telling you near the top of this thread?:shake:

[Glenn]

Pops:

Your excluded from my comments. We all know you are a die hard racer. :banana2:

Glenn :burnout:

[ImpalaSlayer]

Not one person has stated that these mods are for more GO at the track. What is the purpose of spending all this money if you don't also have a goal at the track for your performance improvements. Are all you guys Street Racers or just like the extra power to say you have it?

Glenn Ford :flamer:


at the end of the year i plan to claim a spot higher on the time slip page then you.

ok, lets hear it Glenn, no one can be faster then you because you are god with an awesome trilogy. :stupid:

[Pops]

Pops:

Your excluded from my comments. We all know you are a die hard racer. :banana2:

Glenn :burnout:

Thats better Glenn! I think you will see Doomie playing on the track this year also. He is getting close to having the car ready for a run with the T Bolt! I have a couple of things in reserve just for him on that one!;) They might work if we ever get the chance to line up Glenn!:bows:

[Glenn]

Pops:

I think Donny will go with a SC this year or some radical NA engine work.

Glenn :burnout:

[Pops]

T Bolt will get a new set of heads and intake. Race carbs and a set of slicks. I don"t know if I can have the short block done this year or not. Looks like it will be 12.5 or better compression on the 482 this time around. Roll bars are on the list for both cars. Just need more money!:D

[DOOM]

I heard Glenn is getting some long tubes. :hide:

[merc]

Coming soon.

http://aretheyserious.files.wordpress .com/2009/08/wooly-mammoth.jpg

[FordNut]

Coming soon.

http://aretheyserious.files.wordpress .com/2009/08/wooly-mammoth.jpg

Wicked fast...

[Pops]

Coming soon.

http://aretheyserious.files.wordpress .com/2009/08/wooly-mammoth.jpg

Is it a hemi Mark or do you need to go on a diet!:D

[Phrog_gunner]

I heard Glenn is getting some long tubes. :hide:

He just said he was looking for more show....

[SMOKE]

Not one person has stated that these mods are for more GO at the track. What is the purpose of spending all this money if you don't also have a goal at the track for your performance improvements. Are all you guys Street Racers or just like the extra power to say you have it?

Glenn Ford :flamer:

Ummm - okay, I'm looking to knock a few tenths off my mid-14 runs last fall? :o Not earth shattering but absolutely behind my mod choices....still learning launches and sixty foot times and the lot....so I guess the biggest mod is seat time for me :D.

Best,
Jonathan

[merc]

Is it a hemi Mark or do you need to go on a diet!:D

Both Pops. I just purchased a new car for Pam.

[2,4shofast]

I will not be taking my car to the track, after the stereo install plus all the dynamat it would be rather pointless... I just enjoy driving with the extra power and I do not streetrace..

[ImpalaSlayer]

I will not be taking my car to the track, after the stereo install plus all the dynamat it would be rather pointless... I just enjoy driving with the extra power and I do not streetrace..


you have to go to the track!!!!! otherwise glenn wont like you!

[cougar9150]

Well I will first get my car back together after repairing the oil leaks and installing my freshly rebuilt tranny. During this project I will be installing my new brakes (cryo-treated slotted OE size), replacing all the factory heat sheild with some good stuff that doesn't fall on my cats, and a Metco drive-shaft loop. I may also upgrade from a single disk 3k rpm TC to a triple disk if the funds allow.

I plan in building another sub box because I didn't like the way the one I built for the first MM came out and installing my stereo system This will consist of a Kenwood head unit (nothing special EZ-500) my 800W worth of amplified JL Audio sound (500 for subs, 300 for mids/highs), MB Quartz speakers at all 4 corners, a 10" Kicker L7 Sub, and some sound dampening.

Looking into a custom coilover kit through a local shop but need more info before I can give it the thumbs up.

I will also be ordering my Eaton conversion brackets in the next few days for my birthday present and collecting the rest of the kit slowly throughout the year. Hopefully by the end of 2010 I will be a member of the boosted club, if not early next year depending on fun funds throughout 2010. I may wait until I also have a cobra short block in hand just for safeties sake as I have an issue not pushing limits.

Oh yeah also upgrading whatever breaks throughout the year, and I plan on actually going drag racing for the first time. I will let you know goals Glenn once I know what I am capable of 1st. Long term goal is 500rwp and low 12s to get to where I want the car and would feel satisfied with it. Don't want to be the fastest but want to be faster than most of the mooks I runs into on a daily basis. Need to be able to hunt Hemis with real gun and not a slingshot.

[FordNut]

...replacing all the factory heat sheild with some good stuff that doesn't fall on my cats...

Part # 5w7z-5401588-a

Get it now, replace it before you re-install the engine & transmission. It is highly improved. Thinner, reflective coating, etc. You may also need the stick-on heat shields, part number is listed on these forums somewhere.

I got one and plan to replace mine next time the car is apart, not because of falling down on the cats but because it got saturated with transmission fluid and keeps oozing...

[2,4shofast]

you have to go to the track!!!!! otherwise glenn wont like you!


Yea I have taken it to the track, just didnt enjoy it like I would have thought. I forgot how heavy these cars are and running it at 5400ft hurt my pride even more. I think I will stick to watching friends race while having a few cold ones:beer:

[cougar9150]

Part # 5w7z-5401588-a

Get it now, replace it before you re-install the engine & transmission. It is highly improved. Thinner, reflective coating, etc. You may also need the stick-on heat shields, part number is listed on these forums somewhere.

I got one and plan to replace mine next time the car is apart, not because of falling down on the cats but because it got saturated with transmission fluid and keeps oozing...

I'm replacing it w/something from Summit: http://www.summitracing.com/parts/THE-14620/

Figured I can lay most of this in and cut it to fit where I need. Just need to use a lot of acetone to clean the area good and plenty of patience while laying on my back.

I have the P/N for the Ford pieces from when I did the first MM. At least this time I knew just where to look when I smelt it.

[ImpalaSlayer]

Yea I have taken it to the track, just didnt enjoy it like I would have thought. I forgot how heavy these cars are and running it at 5400ft hurt my pride even more. I think I will stick to watching friends race while having a few cold ones:beer:

i understand, Glenn just thinks every mm is a race car and can only be driving at the track or else he doesn't approve.

[cougar9150]

i understand, Glenn just thinks every mm is a race car and can only be driving at the track or else he doesn't approve.
And they should have shorty headers :P

[FordNut]

I'm replacing it w/something from Summit: http://www.summitracing.com/parts/THE-14620/

Figured I can lay most of this in and cut it to fit where I need. Just need to use a lot of acetone to clean the area good and plenty of patience while laying on my back.

I have the P/N for the Ford pieces from when I did the first MM. At least this time I knew just where to look when I smelt it.

I've used that stuff and it's crapola. If you don't want to use the right pieces from Ford, at least get the good DEI-050503 stuff from Summit.

[cougar9150]

I'm replacing it w/something from Summit: http://www.summitracing.com/parts/THE-14620/



Figured I can lay most o...



I've used that stuff and it's crapola. If you don't want to use the right pieces from Ford, at least get the good DEI-050503 stuff from Summit.

I'll look into the DEI stuff if you say the Thermo-Tec is crap. I already sent TheDealer a message asking for price for the Ford part. If it's not to expensive I'll just go with the OEM replacement.



Sent from my T-Mobile myTouch 3G using Tapatalk

[twin03]

4.10 gears and headers
I second that........

[Pat]

I hope to get control arms and sway bars this year.

[Bradley G]

Does the obvious need to be stated Glen?
What's wrong with the "big stick" approach?
BTW Is it true you are switching to long tubes?:P
Not one person has stated that these mods are for more GO at the track. What is the purpose of spending all this money if you don't also have a goal at the track for your performance improvements. Are all you guys Street Racers or just like the extra power to say you have it?

Glenn Ford :flamer:

[cougar9150]

Thanks Fordnut ordered the insulation through Ray the dealer.



Sent from my T-Mobile myTouch 3G using Tapatalk

[Blackened300a]

I'm a street racer guy who likes the extra power to use on the track once and while.

Besides, going to the track can be a complete PITA. Long lines, expensive food, rednecks and ricers all over the place and after all that, Ill be lucky to get 3 runs in the entire day.
I make the track once a year just for the hell of it, otherwise I'll keep the car in the garage and take it out to embarrass someone on the street.

[swordfish]

I'm hoping for kompressor!!

[Motorhead350]

O2 censors, dyno tune, rear tires, kerosene. Ya know... stuff it needs.

[justbob]

I'm a street racer guy who likes the extra power to use on the track once and while.

Besides, going to the track can be a complete PITA. Long lines, expensive food, rednecks and ricers all over the place and after all that, Ill be lucky to get 3 runs in the entire day.
I make the track once a year just for the hell of it, otherwise I'll keep the car in the garage and take it out to embarrass someone on the street.
I'm with you 87.8% on this one. Not really street race, but the embarrassing factor is quite fun. And the track sucks because they let way to many in!:beer:

[Bradley G]

Not in October and November :burnout:
I'm with you 87.8% on this one. Not really street race, but the embarrassing factor is quite fun. And the track sucks because they let way to many in!:beer:

[Crazieboutamerc]

Let me see for the Grand Marquis, I plan on doing tune up, dual exhaust, CAI, cobra rims & y rated tires.
mostly drive it.

Tim

[DOOM]

Ordered my wilwoods today. :banana2: :woohoo:

[marauderoner]

Let me know how it goes with ur mods cus I also wanna put mods on mine similiar to your


Sent from my iPhone using Tapatalk

[DOOM]

Well as most of you know i just installed my wilwoods and had the J-Mod done. :up:

Tuesday is dyno day! :D :burnout:

My next mod will be a built transmission and then finish off with a detroit tru trac & 31 splines and a new set of M/T ET streets.

[Mr. Man]

Well as most of you know i just installed my wilwoods and had the J-Mod done. :up:

Tuesday is dyno day! :D :burnout:

My next mod will be a built transmission and then finish off with a detroit tru trac & 31 splines and a new set of M/T ET streets.
Still won't beat the T in the MUD!:D

[PurdueRifleman]

Lidio Tune, J-Mod, 4.10's

[Sully008]

Install 3.2" Blower pulley
Install Kooks headers/high-flow cats
Install Powerslot rotors, Hawk HPS pads front/rear
Install TCE SS brake lines front/rear
Install widened wheels w/305-45-18 MT ET Street Radial IIs
Dyno Tune:burnout:

Wheels are @ Weldcraft, need to buy high-flow cats. All other parts are waiting in my basement for the snow to disappear.

[burt ragio]

Continue collecting parts for the eaton conversion half way there. All parts sitting in closet. Maybe I will have everything by my 100th birthday. Install new front Hawk pads & Cryo rotors sitting in closet. Install inline trans temp block that has been sitting in top of tool tray for past three years. Install new Percy exhaust header gaskets before I go completly brain dead from exhaust fumes also sitting in closet. What would I do with out a closets? Maybe own a moped & live on an island.

[EbonyMarauder03]

I need to install my dead pedal and trunk lid plates. I also need to replace my foglight bulbs and reaim them. Lastly, maybe replace my stone pitted windshield at state inspection this year.

[DOOM]

So how are you guys coming along with your mods?

Im about done with mine.

Should be doing my 31 spline axles, cobra diff and M/T drag radials within the next 2 months.

Then its off to the track! :burn: :burnout:

[ctrlraven]

Exhaust system - completed
Trans cooler - installed
Dyno tuning - 10/29/10

[DOOM]

Oh almost forgot my launch control (2 step) :burn:

[Sully008]

Install 3.2" Blower pulley - Done
Install Kooks headers/high-flow cats - Done
Install Powerslot rotors, Hawk HPS pads front/rear - Done
Install TCE SS brake lines front/rear - Done
Install widened wheels w/305-45-18 MT ET Street Radial IIs - Done
Dyno Tune:burnout:- Done

Wheels are @ Weldcraft, need to buy high-flow cats. All other parts are waiting in my basement for the snow to disappear.


Well, looks like I accomplished a lot this year, lol! Dyno'd 443rwhp, 403rwtq., best 60ft. time: 1.73sec., best 1/4mi. time: 12.334@110.1mph. Looking forward to 2011's mods.:D

[FordNut]

CAI tube upgrade (actually that was a '09 mod but it's not back from ceramic coating yet), crankcase vacuum pump/PCV revision. Done, but still needs a tune

Figure out how to make a bolt-in roll bar that fits. Got a plan, maybe 2011

If I get a job, maybe a 9" rear end. Still no job, so maybe next year

Didn't get all of it done, but I did get the mufflers swapped to Borla.

[justbob]

Might change the brand of washing soap?:dunno:Nope, I just used last years stuff.:rolleyes:
....................

[hotford]

Te next mod is a set of brembo' brakes for the MM,I have everything just finding the time to do it.

wrinkle black valve covers, with the powered by ford coil covers.:coolman:

[FW_Linc/Merc]

Nightshaded taillighs. I need a left one since I screwed up my spare set polishing them too much.

Badgeless grille if I get around to it.


Finished the taillights. Jon's tinted tails did a great job. Love the look. Will sell one spare set soon.

Badgeless grille will be next year.

[RacerX]

2010 Mods:

Done:
Forged SB
P&P Heads
98 Cobra cams
P&P Intake
Shorty Headers
Cobra Exhaust and X-Pipe
GT40 FP
Z**K Tune
N2O Bottle Warmer
Triple gauge pod
A/F Wideband
N2O Gauge
Vacuum/Boost Gauge

To Do:
Drag Radials
31 Spline Axles and 31 spline carrier
Cloyes adjustable secondary cam gears (on their way!)
Remote Bottle Opener
Two Stage RPM Window Switch
N2O Switch Control Center (To clean up the switch/wire mess)
Widen Rims
SC (Eaton or Vortech...)

[SC Cheesehead]

I got a couple things in the works...

[fastblackmerc]

Lots of "stuff" in boxes in the garage. Stock parts and aftermarket.

Too little free time.

[breeze]

no cai and tune but she sounds, handles and brakes alot better. 2011 keep ya eyes open :neener:

[dohc324ci]

Well first I must find a tuner that's competent...LOL then...

Replace Fuel Pressure Sensor
Accel COP
FRPP Shorty Headers w/14" Magnaflows Re-tune
Buy Jdennings002 - 4R75W Transmission and a 2800TC
Maybe - 31 Spline Axles w/LSD and 4.10s, DS w/DS loop
Replace BFGs


Well not exactly:
Replace Fuel Pressure Sensor - Done
Accel COP - Done
FRPP Ceramic coated shorty headers, Magnaflow X, Mach I mid-pipe swap, 2.5" to Corsa db blacks - Done
Buy Jdennings002 - 4R75W Transmission and a 2800TC - Done
Maybe - 31 Spline Axles w/LSD and 4.10s, DS w/DS loop - NO maybe 2011
Replace BFGs - Done

Plus:
FRPP Blue Valve Covers
FRPP Camshaft kit -minus springs
32 lash adjusters

[LANDY]

Got everything done but the rearend and the shortblock. Now the beast is down for tranny work

[LANDY]

What's funny is that I did lots of other things to the car instead of concentrating on the list

[DOOM]

Ordering my cobra diff & 31 splines. :banana2:

[MOTOWN]

odering my hids for the fogs, and my dead pedal

[Shermanator]

Quarter Mile ET.

[SC Cheesehead]

Got the Eaton swap done (tip of the hat to ImpalaSlayer).

Have the parts, but it looks like I'm going to have to wait until 2011 to get the exhaust work done.

[PurdueRifleman]

JLT CAI, Steeda UDP's, and hopefully my exhaust work gets completed by tomorrow. 2011 will hopefully see 4.10 gears and the start of gathering parts for an eaton swap.

[Pops]

New tranny coming soon! Watch out Sherman cause Pops is looking for you!:burnout:

[CBT]

New tranny coming soon! Watch out Sherman cause Pops is looking for you!:burnout:

Careful, his plates have I DO 12's on them! :D

[Pops]

Careful, his plates have I DO 12's on them! :D He must have that memory problem going on. He is way older than me!!!!:D

[CBT]

He must have that memory problem going on. He is way older than me!!!!:D
I love Shermans tags, talk about an understatement.
Your son still trapped up there?

[Pops]

Made it home last night. He flew into Richmond and someone picked him up.

[CBT]

Made it home last night. He flew into Richmond and someone picked him up.
Richmond?! There's 2 airports between his 'hood and Richmond.

[Pops]

The only other flight he could get on took him to Newirk and then home. 9.5 hours total time. Its all screwed up!:D

[SC Cheesehead]

New tranny coming soon! Watch out Sherman cause Pops is looking for you!:burnout:

So, what; Doomie's completely off your radar screen now?

[DOOM]

New tranny coming soon!

Mail order men.com :rofl:

[SC Cheesehead]

Mail order men.com :rofl:

I'd be insulted, Jake, Pops has already written you off...http://www.bloodydecks.com/forums/images/smilies/idiot.gif

[Pops]

I'd be insulted, Jake, Pops has already written you off...http://www.bloodydecks.com/forums/images/smilies/idiot.gif

Rex this is funny!:beer:

[CBT]

I'd be insulted, Jake, Pops has already written you off...http://www.bloodydecks.com/forums/images/smilies/idiot.gif

I was going to say Pops has moved on to bigger and better things, but I've met DOOM and Sherm. Better, maybe. Bigger, yeeeeaaahhhh, I don't know about that one, it's close :D

[Pops]

Sherman has me on the racing deal.:bows: He also knows that I could get lucky and lay a number down once I get her sorted out. :D I need to take 500 pounds out her to make it a race. It will be a fun year at the track.:)

[Mr. Man]

Santa was nice so I see suspension Mods and rubber for Mr Black and brakes for Thor in 2011. If there's anything left engine dress up.

If you cut a coil out of stock springs can you still use the oem struts?

[Shermanator]

You guys are losing it. Pops, I am as much older than you as much as I am faster than you. You should stick with the comp with Doom, you have a chance there, not much, but a chance. That is if you can get the bling man to bring it out, which ain't going to happen in 2011. And I sure am happy that I'm not the oldest on the site. Happy new year to you all.

[DOOM]

You should stick with the comp with Doom, you have a chance there, not much, but a chance.

Spoken from the master! :nworthy:

Even the general know's you will suffer a defeat from the wrath of
DOOM!!!



:beer:

[Pops]

Spoken from the master! :nworthy:

Even the general know's you will suffer a defeat from the wrath of
DOOM!!!



:beer:

Funny I read it just the other way Doom. I think he meant he was going to Kick My AZZ! Took it he meant I had you covered!!!!:lol:

[SC Cheesehead]

Funny I read it just the other way Doom. I think he meant he was going to Kick My AZZ! Took it he meant I had you covered!!!!:lol:

That's the way I read it, too. Yup, yup, yup...

[DOOM]

You 2 morons can't read! :shake:

[SC Cheesehead]

You 2 morons can't read! :shake:

Pops, I can read; can you read?

And I think we can both comprehend as well.

Denial is a terrible thing, ain't it....:D

[DOOM]

We can line up all 4 cars at Z max!

I'll bet any amount of money I WONT come in last place! :D

[SC Cheesehead]

We can line up all 4 cars at Z max!

I'll bet any amount of money I WONT come in last place! :D

Well, you definitely got me there, bubba, but third out of four is a possibility... ;)

[CBT]

Santa was nice so I see suspension Mods and rubber for Mr Black and brakes for Thor in 2011. If there's anything left engine dress up.

If you cut a coil out of stock springs can you still use the oem struts?

Am I the only person who is trying to picture Mr. Man in a Marauder with part of it's springs missing? :lol:

[Shermanator]

Hey, Doom has a great idea. Four of us side by side at ZMAX. Pops will pay the track rental. Or should it be the last to the finish line?

[Pops]

Last to the finish line buys!

[Marauderman]

We can line up all 4 cars at Z max!

I'll bet any amount of money I WONT come in last place! :D


Well, you definitely got me there, bubba, but third out of four is a possibility... ;)


Hey, Doom has a great idea. Four of us side by side at ZMAX. Pops will pay the track rental. Or should it be the last to the finish line?


Last to the finish line buys!

Hey Rex------Maybe its time we return to Z-MAX guys and see about renegotiating a mini contract -you never know----could be a special Marauder Ad event we could pull off.......?????