What did you do to your car today?

[loud2004marquis]

Added a third gauge to a spare gauge pod:

http://www.supermotors.net/getfile/1074499/fullsize/dsc04216.jpg

[1Marauder]

Warmed up both cars and took them each for a ride... Wanted to end the year with a burned rubber smell, and a smile. And to compare suspension mods on Silver side by side to black. Wow!

Both back safe in garage by 5pm/dark.

Still smiling about the drives though. Happy New Year!

[daddyusmaximus]

New LCM for free at the dealer... I can drive at night now.

[lji372]

This is more what I did for my car today.
Finally got the garage heater going. No more carting stuff in the house so it doesn't freeze either :2thumbs:

Hot dawg!!!!!!



http://images.tapatalk-cdn.com/16/01/01/17588dc72810aa3c49ea1f2bf51f73 ce.jpg

[justbob]

This is more what I did for my car today.
Finally got the garage heater going. No more carting stuff in the house so it doesn't freeze either :2thumbs:

Hot dawg!!!!!!



http://images.tapatalk-cdn.com/16/01/01/17588dc72810aa3c49ea1f2bf51f73 ce.jpg


You'll love it. I've had mine a couple of years now but only use it when needed as I don't have any insulation.

I was also running it without a thermostat the first two years and let me tell you it gets HOT! Seriously, it nothing to hit 85* when it's only 10* outside. [emoji6]


Sent from my iThrone using Tapatalk

[sailsmen]

You may have more than just a hot dawg when that aerosol can and gas pump adds to the heat.

[lji372]

Oh snap.

Thought they had all been moved away.
Good catch.

Fyi gas pump only for show :D

Thank you sir.

[justbob]

I actually came across three commercial hanging furnaces by pure luck in a building that had already began demo and the area they were in was scheduled for the next morning. I was capping off existing water lines and sanitary and noticed them. Seeing as how the entire building contents are turned over to the demolition crew I went straight to the foreman and asked about them. He says which one? I said all... He said $50 each and I got too wrenching!

All of them were functioning. One was dated 30 years old and tiny - craigslist sold $150, 2nd unit 10 years old 100,000 BTU in pristine condition - kept it for home. 3rd THREE MONTH OLD 120,000 BTU Lennox (too damn big) craigslist fire sold $450...

80' gas pipe and fittings from basement to under deck, under ground for 10', and pipe'd to the unit in the garage FREE from another demo a month prior. Only purchase was a $30 thermostat and the two leader pipes in and out of the ground $150.

Win.

http://images.tapatalk-cdn.com/16/01/01/bb1c88791b6a5082d0cf0514e202f3 9a.jpg




Sent from my iThrone using Tapatalk

[Pat]

I'm getting long in the tooth, so my helpers took advantange of a dry day with a little sun to wash and polish the MM. Jackson and Aston, the two boys, said that it's the best car in the neighborhood. Jason, my Honda mech, agrees.

[lji372]

I actually came across three commercial hanging furnaces by pure luck in a building that had already began demo and the area they were in was scheduled for the next morning. I was capping off existing water lines and sanitary and noticed them. Seeing as how the entire building contents are turned over to the demolition crew I went straight to the foreman and asked about them. He says which one? I said all... He said $50 each and I got too wrenching!

All of them were functioning. One was dated 30 years old and tiny - craigslist sold $150, 2nd unit 10 years old 100,000 BTU in pristine condition - kept it for home. 3rd THREE MONTH OLD 120,000 BTU Lennox (too damn big) craigslist fire sold $450...

80' gas pipe and fittings from basement to under deck, under ground for 10', and pipe'd to the unit in the garage FREE from another demo a month prior. Only purchase was a $30 thermostat and the two leader pipes in and out of the ground $150.

Win.

http://images.tapatalk-cdn.com/16/01/01/bb1c88791b6a5082d0cf0514e202f3 9a.jpg




Sent from my iThrone using Tapatalk

Nice score!!

The buddy I did the 'something different' plate for gave me a 100k btu reznor. He bought it new years ago but never used it. I told him it was too big but he insisted. Grrr sold it to my brother cheap and picked up something that fit my 8ft ceiling better :2thumbs:

[MOTOWN]

Installing my Cdub special radiator! With Spall extreme duty fans 2K cfm each!
http://i1020.photobucket.com/albums/af324/sims36/Mobile%20Uploads/20151229_172743_zpsscynn29i.jp g

[justbob]

Damn! I think my single is only 2K! But with the 170* stat she always seems to stay below the halfway mark.

Only once she started to creep up higher than I'd like. It was 95* or so and I let it idle with the A/C as a test. It stayed good for at least 15 min, then slowly started to raise.

Yours won't be capable of running hot LOL.

Edit: 2,200 CFM
Sent from my iThrone using Tapatalk

[MOTOWN]

Damn! I think my single is only 2K! But with the 170* stat she always seems to stay below the halfway mark.

Only once she started to creep up higher than I'd like. It was 95* or so and I let it idle with the A/C as a test. It stayed good for at least 15 min, then slowly started to raise.

Yours won't be capable of running hot LOL.

Edit: 2,200 CFM
Sent from my iThrone using Tapatalk

Thats exactly what im hoping for, i set the fan controller to come on @ 170* when the thermostat opens , the fans are off @ 165* , the true test will be one of these 95* summer days we get in Atlanta!

[98MERC]

http://s17.postimg.org/u9hewbhdr/IMAG0131.jpg (http://postimg.org/image/gft279osb/full/)

Painted my grille today

[stryker]

:D Well yesterday I was in the land of shadow and death of the Panthers (the junkyard) and buy the complete double exhaust from a 2010 Crownvic Police Interceptor I will try to post pics late.

[Bob Mathis]

Drove the Marauder to work and it sure was a great drive. Weather was cool and clear. No bugs and the car really liked the air. it had been in the shop and had not moved for a few weeks. Love this car.

[fastblackmerc]

Thats exactly what im hoping for, i set the fan controller to come on @ 170* when the thermostat opens , the fans are off @ 165* , the true test will be one of these 95* summer days we get in Atlanta!

From Reische Perfoormance website.


"Additional Cooling System Improvements

It is important that the fan settings in your tune are set up properly to see the best possible heat dissipation from your cooling system. Otherwise a low temp thermostat will only be effective when the vehicle is moving because heat cannot be removed unless there is air passing through the radiator. Typically with our 170° thermostat installed your cooling fan(s) should be set to turn on between 184-190° and shut off between 176-182°, if not then re-flash your tune with the appropriate settings.

Water transfers heat more effectively than antifreeze so we recommend using the lowest concentration of antifreeze possible for your climate along with a product like Redline Water Wetter. Just make sure you have enough antifreeze in your coolant to keep it from freezing in the winter and always run no less than 20% in a street car. We do not recommend adding Water Wetter to coolant that is more than 40% antifreeze."

[stryker]

Working with one of the sidemarkers of my Panther.

[MOTOWN]

From Reische Perfoormance website.


"Additional Cooling System Improvements

It is important that the fan settings in your tune are set up properly to see the best possible heat dissipation from your cooling system. Otherwise a low temp thermostat will only be effective when the vehicle is moving because heat cannot be removed unless there is air passing through the radiator. Typically with our 170° thermostat installed your cooling fan(s) should be set to turn on between 184-190° and shut off between 176-182°, if not then re-flash your tune with the appropriate settings.

Water transfers heat more effectively than antifreeze so we recommend using the lowest concentration of antifreeze possible for your climate along with a product like Redline Water Wetter. Just make sure you have enough antifreeze in your coolant to keep it from freezing in the winter and always run no less than 20% in a street car. We do not recommend adding Water Wetter to coolant that is more than 40% antifreeze."

I talked to Reische over the phone for 45minutes he recommended the settings im running based on my combination.

[stryker]

:cool: Today I finish the transmission fluid service and installation of a high capacity Pan with drain plug and a kit to protect the 8.8 differential form a rear collision and prevent damage to gas tank I suppose I did a test drive to check for noises or something strange on transmission after the tune up but until now everything is ok and transmission is working very great

[Gerry24]

Starred at her in the garage...

[lji372]

Drove it, felt good.

Did a nice smokey burnout!!!!!! :woohoo:

[RubberCtyRauder]

Drove it, felt good.

Did a nice smokey burnout!!!!!! :woohoo:

"It"..you have like 5..so spill the beans, which one was "it"

[J-MAN]

Yeah, really you need to number the cars or give them names. I can think of a few, but not for publication on pg.net. :D

[JustRight]

Started the mods. Jacked up the back end with extender shackles, put a one foot tall snorkel hood scoop on her. Static straps, yellow fog lights, STP stickers and fuzzy dice complete the ensemble.

Just fooling! Now that I won't have to make another huge donation to my daughter's life fund, new tires was the first thing on the list.

P.S. I know it doesn't have leaf springs. :D

[Shaijack]

Washed blue with a Brillo pad...

[BUCKWHEAT]

Washed blue with a Brillo pad...
So was that a major improvement? You could have just traded for a DTR.
kidding...

[lji372]

Washed blue with a Brillo pad...

thanks for the tip. i normally use steel wool but brillo pads are presoaped :2thumbs:

[slickster]

Logo lights in doors. Washed it. Looked at it

[8UWITH6]

Made sure the trickle charger was plugged into the wall on Blue. Looked at Eaton Swap hawtness while enjoying a beer. Went back in the house. True story.

[8UWITH6]

Washed blue with a Brillo pad...

Your ate up. If you did that to a Blue you know ALL the paint would fall off. I blew a chunk off my quarter panel the size of a dime at the car wash with the wand 2 days after I got it!

[Spectragod]

Well, it didn't get done in one day, but.......

Accusump pre oiler
Replacement Melling oil pump
Timing chains, tensioners, guides
LJI tensioner bracket
2.75 pulley
Killer Chiller
Cobra Engineering rear cooling mod
Mechanical oil pressure and fuel pressure gauges w/isolaters
Will need a re-tune for certain
Car will still run low 16's

[MMcactusflower]

Beautiful clear sunny day here in the Texas hill country...temp 67 right now...so the wife and I took the DTR garage queen (23,000 miles) out on the country roads (paved of course) and drove out and about for an hour or so.
Were it not for the surging type engine "issue" when stopped the car recently has developed, it would have been a fantastic drive. I guess I will have to look into that engine problem soon enough...but I was able to put 'The Colonel' through his paces and blow it out some.
Great fun and time well spent.

[JustRight]

Let me get this newbie question out of the way. What does DTR mean?

[justbob]

Let me get this newbie question out of the way. What does DTR mean?


Don't Try Racing (with a red) or as some here think Dark Toreador Red.


Sent from my iThrone using Tapatalk

[2mercs]

Joe told me it was darn tasty roofies.

[Pat]

I didnt do anything to my MM, but I did check out a transmission repair shop in town as reference against future need. This shop was recommended to me by the shop foreman at the Sheriff's garage.

The tranny repair shop looked like a hole in the wall junk yard, housed in an old converted gas station. Wouldn't have given it a second look.

However it came highly recommended. The police and sheriff's department use it exclusively and when I asked about returns the respective service departments said the repaired tranny's never had to be returned.

I said, "well, I've never seen a police/sheriff car there". The foremen said "we remove the transmissions ourselves and only send them the transmissions". Ah!

So, I visited the shop and was impressed with their knowledge and the questions they asked me about how I service my tranny. The owner/manager said that based on my usage and maintenance schedule I should have no problems with the transmission. He even identified, correctly, the type transmission used in the 04 Marauder as a 4R75W.

I came away feeling this shop was competent and trustworthy. Can't judge a book by it's cover, eh.

[cer0413]

Don't Try Racing (with a red) or as some here think Dark Toreador Red.


Sent from my iThrone using Tapatalk
I hate you lol

[cer0413]

Removed my old aftermarket alarm and programmed two keyless entry remotes.

[SOSA03]

took the cover off looked at her and covered her back

[SteelQualityMan]

I installed the new headlamp harness I got from GoldPanther in my MM. Next I'm going to do the same thing on my Crowne Vic. These harnesses are beautifully made and made to last. I recommend them highly. Combined with a new lamp control module I really have a very reliable belt and suspenders solution. The idea of losing my headlights on a back country Indiana road, as happened with the crappy harness that came with my HIDs is pretty scary.

Sent from my LG-H901 using Tapatalk

[Invader]

I test fitted the grille I've been working on today. A few little things left to do, then off to paint! http://uploads.tapatalk-cdn.com/20160205/5e0ba047c8f3c6367c657794341f95 0e.jpg


Sent from my iPhone using Tapatalk

[svtrichie]

Washed her up

[MOTOWN]

Give me 3 cars , and the crack , and I may be able to keep up with the blue gt!

[CWright]

I test fitted the grille I've been working on today. A few little things left to do, then off to paint! http://uploads.tapatalk-cdn.com/20160205/5e0ba047c8f3c6367c657794341f95 0e.jpg


Sent from my iPhone using Tapatalk



Is that a Police Interceptor grill?

[Invader]

Is that a Police Interceptor grill?


No... It's this grille I built from scratch...http://uploads.tapatalk-cdn.com/20160205/2e0c4c6bda44dacab87eca8bb24824 7d.jpg


Sent from my iPhone using Tapatalk

[CWright]

Ahhh, I see with the close up!

[Invader]

Ahhh, I see with the close up!


I'm also doing some fiberglass work to another MM front bumper, to incorporate the same mesh in the air damn. It should change the look of the car completely...


Sent from my iPhone using Tapatalk

[justbob]

Removed my old aftermarket alarm and programmed two keyless entry remotes.


Thank gawd.....


Sent from my iThrone using Tapatalk

[1Marauder]

Checking into getting big fat flat black stipes, up front over hood roof truck, and done back... Can't wait!

[8UWITH6]

Looked at Blue. Put battery charger on it. Meh

[daddyusmaximus]

New floor mats and steering wheel cover yesterday. They had all 4 branches at the "Patriot store". (Small PX inside the VA.)

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/cars001/floor%20mats_zpsncrgpw8c.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/cars001/floor%20mats_zpsncrgpw8c.jpg.h tml)

New head unit today.

Kenwood DDX 393 Probably gonna take me a month to figure it out...

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/cars001/Stereo%20Kenwood%20DDX%20393_z psxulbhhiw.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/cars001/Stereo%20Kenwood%20DDX%20393_z psxulbhhiw.jpg.html)

[cer0413]

Thank gawd.....


Sent from my iThrone using Tapatalk
Lol, you remembered.

[1Marauder]

First sunny warmer day in Northern California in 8 weeks!

Uncovered, let them each ideal five minutes, and then took each out and SHREDDED some rubber!

Silver car is SWEET w updated suspension. After rubber donation to State of CA roadways, I drove Black to my office and loaded the ADDCO new sway bars, KYB front shocks, SBC camber bolts and all bushings etc. nto trunk -- getting ready for the final suspension installation and alignment.

Working on ordering big brake kit parts now. Need a paper route to help fund the cause.

[redmercy04]

Don't Try Racing (with a red) or as some here think Dark Toreador Red.


Sent from my iThrone using Tapatalk
Is it any truth that DTR are slower or is it just a ongoing joke. Always wondered

Sent from my LG-H810 using Tapatalk

[svtrichie]

Sold it!! But a little sad

[Spectragod]

Is it any truth that DTR are slower or is it just a ongoing joke. Always wondered

Sent from my LG-H810 using Tapatalk

Of course DTR's are slower, I have one, even with mod's it runs 16's, tried filming a burnout, it took so long my camera operator fell asleep....:D

[redmercy04]

Of course DTR's are slower, I have one, even with mod's it runs 16's, tried filming a burnout, it took so long my camera operator fell asleep....:D
Lol smh ok ongoing joke

Sent from my LG-H810 using Tapatalk

[MOTOWN]

Notice his sig a TWIN SCREW ! Lol

[03Merc]

Added a third gauge to a spare gauge pod:

http://www.supermotors.net/getfile/1074499/fullsize/dsc04216.jpg


Where did You install the water temp sender?


#1618 of 3214

[lji372]

Pounced on the new sicmerc on my way into work this morning and on the way home tonight.
Weird, never had a blown motor with such powa before ;)

Adjusted eq for firm bass with more rear

[MOTOWN]

Pounced on the new sicmerc on my way into work this morning and on the way home tonight.
Weird, never had a blown motor with such powa before ;)

Adjusted eq for firm bass with more rear

Which one is that :confused:

[justbob]

Which one is that :confused:


I'm thinking the new black.


Sent from my iThrone using Tapatalk

[MOTOWN]

Hell which new black? Dtubs , or Jmans? Lol

[justbob]

Hell which new black? Dtubs , or Jmans? Lol


Crap. I can't keep up with all his cars? I forgot he even bought Jmans! [emoji22]


Sent from my iThrone using Tapatalk

[cer0413]

http://uploads.tapatalk-cdn.com/20160209/b8d4179af1771d718618f1fed72b50 05.jpg

Picked these up.

[MOTOWN]

http://uploads.tapatalk-cdn.com/20160209/b8d4179af1771d718618f1fed72b50 05.jpg

Picked these up.

Looks good!

[cer0413]

Looks good!
I just hope it look good on the engine lol

[slickster]

Put gas in it. Disconnected the battery. Steering club. Blocked it in with the truck and left it 1800 miles away. Inlaws crap never ends!!!

[Gerry24]

Took her to work today so she can enjoy the cool weather down here.

[sexygomer]

Got the motor back in, finally. http://i.imgur.com/YfxZDOcl.jpg

[merc]

http://uploads.tapatalk-cdn.com/20160209/b8d4179af1771d718618f1fed72b50 05.jpg

Picked these up.

Where have I seen that color combination before?

[MOTOWN]

Got the motor back in, finally. http://i.imgur.com/YfxZDOcl.jpg

Looks good , and you have the nice 3 bolt tensioner cover!;)

[fordnut02]

New Bumper all painted and ready to Install this Spring

[cer0413]

Where have I seen that color combination before?
Idk but if you manage to find the pic please post it. Before I powder coat the lower intake and upper lid, I want to see how it all looks together.

[jimreed2160]

The previous owner installed a blackout grille. It looked OK, but never struck me as Marauderish enough. Lucky me when CWright came forward with a replacement.

I like the new look. The jewelry adds a nice touch.

[ChiTownMaraud3r]

The previous owner installed a blackout grille. It looked OK, but never struck me as Marauderish enough. Lucky me when CWright came forward with a replacement.

I like the new look. The jewelry adds a nice touch.

Looks good. PM sent on badgeless lol.

[CWright]

The previous owner installed a blackout grille. It looked OK, but never struck me as Marauderish enough. Lucky me when CWright came forward with a replacement.

I like the new look. The jewelry adds a nice touch.


Looks great buddy! :beer:

[sam]

after being down for nearly 2 year, the M fired up yesterday for the first time after
the Eaton install :)

[cer0413]

after being down for nearly 2 year, the M fired up yesterday for the first time after
the Eaton install :)
Congrats!!!!!

[WhatsUpDOHC]

Looks good. PM sent on badgeless lol.
Dangit!!!!!

[MOTOWN]

Found a great deal on a Meziere electric water pump, been wanting one forever.

[sam]

Congrats!!!!!


Thanks you sir, its been a painful 2 years gathering every part.
My tuner did the install just waiting on final dyno numbers

[cer0413]

Thanks you sir, its been a painful 2 years gathering every part.
My tuner did the install just waiting on final dyno numbers
I've never driven a s/c car but from riding in one, its worth the wait.

[Sactown]

Changed plugs and coils...running much better now :)

[lji372]

Changed plugs and coils...running much better now :)

Great to hear :beer::beer:


Drove a blown one today, stayed steady and eventually the tires stuck :banana2::banana2:

[daddyusmaximus]

Got to drive her fast today!

Took the wife and daughter out prom dress shopping. (and stopped by the stereo shop to get my new rear speakers) Took too long farting around at Applebee's during supper and had to make an ~85 to 90 mph blast down the highway to get home in time for "Crinimal Minds". (Only to find it wasn't even on this week for some stupid reason, &@^%$!) Got stuck behind two 18 wheelers when one slow truck was passing a very slow truck... in a string of trucks from the movie "Convoy".

I saw a gap where I could zig-zag to the other lane, pass, and get back over if I got on it. Took the chance. By the time I went around this one rig we went from 60 to 90, and it was effortless! I love this car!


Now watch me get a damn ticket soon, after not having one in 15 years.

[1Marauder]

Got to drive her fast today!

Took the wife and daughter out prom dress shopping. (and stopped by the stereo shop to get my new rear speakers) Took too long farting around at Applebee's during supper and had to make an ~85 to 90 mph blast down the highway to get home in time for "Crinimal Minds". (Only to find it wasn't even on this week for some stupid reason, &@^%$!) Got stuck behind two 18 wheelers when one slow truck was passing a very slow truck... in a string of trucks from the movie "Convoy".

I saw a gap where I could zig-zag to the other lane, pass, and get back over if I got on it. Took the chance. By the time I went around this one rig we went from 60 to 90, and it was effortless! I love this car!


Now watch me get a damn ticket soon, after not having one in 15 years.


Knock on WOOD!

[1Marauder]

Uncovered, let idle while I cleaned windshield, and waxed hood and trunk. Took SB to muffler shop where I had an appointment to have the RES DEL MEGS installed, only to find the "old man" muffler expert had called in sick. The owner and son offered to do it, but was worried "that we was shorthanded..." I joked that I wanted them BOTH to do it together-father and son.

So, I opted to wait till next Tuesday.

Gave me a chance to "take a lap" and enjoy the new suspension parts. Chirped effortlessly at light, again over hump at intersection, and across the intersection on the cross walk paint, had never done that before.

Can't wait untill next Tuesday!

Can't wait to finally drive the car--thinking about a Vegas Run in it March 24-28, and maybe even stopping in to see Mike - Big Boss Applesauce.

[justbob]

Took it for a joyride.


Sent from my iThrone using Tapatalk

[Mebot]

Installed new Ford Racing coil covers

http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/tapatalk_1456014820618_zpsvjvp h1ce.jpeg

Before:
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_155030_zpszhob6iug.jp g

After:
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_160425_zpsaxofnzzg.jp g
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_160435_zpsz4ljizvm.jp g


Can't stop the signal...

[Mebot]

after being down for nearly 2 year, the M fired up yesterday for the first time after
the Eaton install :)
That's awesome! Sorry we never got a chance to meet up before I moved out of Virginia. Let's see some pics of the set up

Can't stop the signal...

[justbob]

Those covers really did up that engine Ryan! [emoji1303]


Sent from my iThrone using Tapatalk

[MOTOWN]

Installed new Ford Racing coil covers

http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/tapatalk_1456014820618_zpsvjvp h1ce.jpeg

Before:
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_155030_zpszhob6iug.jp g

After:
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_160425_zpsaxofnzzg.jp g
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_160435_zpsz4ljizvm.jp g


Can't stop the signal...

Those look much better on your ride than mines , glad to see they went to a good home!

[MOTOWN]

Installed a Mizzerre electric water pump, this thing is a work of art, and something i should have done a long time ago, idles much cooler in stop and go traffic, just about ready for the 90* + summer weather.

[Mebot]

Those covers really did up that engine Ryan!



Those look much better on your ride than mines , glad to see they went to a good home!

Thanks Bob! and thanks MOTOWN for the quick shipping! My engine bay pen0r is not as large as CDubs, but I think the contrast of black and blue is quite striking.

I'll be boosted soon....

[1Marauder]

Stared at it in my garage.
Since i havent driven it since early november. :bigcry:



DOOM IS ALIVE,

Zzzttuppp brother?

[Mebot]

Doom has posted here in like 3 yrs

[loud2004marquis]

Quote:
Originally Posted by loud2004marquis http://www.mercurymarauder.net/forums/images/buttons/viewpost.gif (http://www.mercurymarauder.net/forums/showthread.php?p=1479211#post1 479211)
Added a third gauge to a spare gauge pod:

http://www.supermotors.net/getfile/1074499/fullsize/dsc04216.jpg


Where did You install the water temp sender?

Into the heat exchanger for the blower.

[Limited360]

Any takers at $65?

http://www.ebay.com/itm/301875262626?item=301875262626&viewitem=&vxp=mtr

[03Merc]

4328343284

4.10s Installed with a Trans Pan drop with 4-5 fresh quarts of fluid.


#1618 of 3214

[03Merc]

Any takers at $65?

http://www.ebay.com/itm/301875262626?item=301875262626&viewitem=&vxp=mtr


I would if I had the hitch installed. I think that's pretty damn cool.


#1618 of 3214

[daddyusmaximus]

New fender badges, and HID headlights.

Badges look backwards, I know. I wanted the word to go before the flag.

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/cars001/041_zpsqybnps9o.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/cars001/041_zpsqybnps9o.jpg.html)

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/cars001/040_zpsvpefr6dq.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/cars001/040_zpsvpefr6dq.jpg.html)

The HIDs made a huge improvement. This is the old ones pointing into my back yard.
http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/cars001/034_zps1apllomk.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/cars001/034_zps1apllomk.jpg.html)

The HIDs are way better, and came with a relay harness.

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/cars001/044_zps5tbmxq0y.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/cars001/044_zps5tbmxq0y.jpg.html)

[MGDriver]

Drove it across Europe, from Germany to England crossing through the Netherlands, Belgium and France as well as a ferry ride across the British channel, roughly 500 miles.


New fender badges, and HID headlights.

Badges look backwards, I know. I wanted the word to go before the flag.

I have a set of those coming to me as well, thanks to your pictures I now definitely know they'll look good on the car, looking forward to put them on!

[Sactown]

Thanks to the nice weather I gave her a much needed bath and rainx on the windows. Now it will certainly rain :wflag:

[slickster]

Drove it across Europe, from Germany to England crossing through the Netherlands, Belgium and France as well as a ferry ride across the British channel, roughly 500 miles.



I have a set of those coming to me as well, thanks to your pictures I now definitely know they'll look good on the car, looking forward to put them on!

Pictures would have been very cool

[03Merc]

Ordered the TCE Brake Line kit. They are a MUST have with the 4.10s installed now.


#1618 of 3214

[fordnut02]

Replace my Bumper and tailights today, and trunk padding

[slickster]

Ordered the TCE Brake Line kit. They are a MUST have with the 4.10s installed now.


#1618 of 3214

That's going to be one of the best mods you'll ever do.

[1Marauder]

Installed fresh new set of MEGS res delete tips, extended back 3/4 inch farther (not further) than my black. No drone at all! Just a nice hearty rumble and growl when getting into it!

Boxed up my 30,000 mile stock tips.

THANK YOU JERRY!

[03Merc]

That's going to be one of the best mods you'll ever do.


I saw You write that a couple times so I jumped on it right away. Thank You!


#1618 of 3214

[slickster]

Just got a jacket for it size s that fits like a m new with tags mint condition for 175? Yep. Will sell one of my m ones soon

[Sactown]

Thanks to the nice weather I gave her a much needed bath and rainx on the windows. Now it will certainly rain :wflag:

Yup it rained tonight with a 0% rain forecast :mad2::banghead::wflag:

[MOTOWN]

Ordered a set of super wide Mickey Thompson street radials for the rear , no turning back on the mini tub project now!

[chief455]

Ordered a set of super wide Mickey Thompson street radials for the rear , no turning back on the mini tub project now!

:eek: DUDE - mini tubs:banana: that will be killer!

[MOTOWN]

:eek: DUDE - mini tubs:banana: that will be killer!

Yeah i ordered Mickey Thompson street radials in a 29" tall , by 15" wide , 20" tire!:coolman:

[chief455]

Yeah i ordered Mickey Thompson street radials in a 29" tall , by 15" wide , 20" tire!:coolman:

narrowing the 8.8, or going big 9" :confused:

[MOTOWN]

narrowing the 8.8, or going big 9" :confused:

Im keeping positive offset wheels, probably going to widen again to 13" wide , really looking at going with the Moser M9 housing.

[justbob]

Im keeping positive offset wheels, probably going to widen again to 13" wide , really looking at going with the Moser M9 housing.


Pure sex. I've wanted it for years just for looks LOL

43334


Sent from my iThrone using Tapatalk

[MOTOWN]

Pure sex. I've wanted it for years just for looks LOL

43334


Sent from my iThrone using Tapatalk

Yes sir! I've wanted to put a 9" under the Marauder since i bought it, I blame Lifespeeds thread! Lol

[camelgrundle]

I want pics of your rear end ;)

[Sactown]

Well I did something with my MM today...took it to a morning meetup with a fellow forum member. Grant it was a pleasure to meet you, you have a very clean ride.

[03blackvegas]

Finally removed the wipers, clean as a whistle. My removal tool helped sliding off the spline.

[03blackvegas]

More pics.

[Sactown]

Finally removed the wipers, clean as a whistle. My removal tool helped sliding off the spline.

Removal tool? Where do I get such a thing?

[Gerry24]

Washed the ol'lady's car, the MM and the the Vic... In and out, was pretty worn out by the end. The weather was real nice today, probably take out the MM tommorrow for a spin.

[03blackvegas]

Removal tool? Where do I get such a thing?

I would search e-bay, or your local tool truck.

[MyBlackBeasts]

New rear leaf springs on New Blue this weekend.

I HATE working on the fricking floor!!! :mad2:

Glad that's done...

[TJCOX]

Today: I replaced the rear axle seals and for some reason the driver's side axle has too much end play. The right side is good. Does anyone else have this problem? Installed 8oz of Motorcraft friction modifier and just under 2 quarts of 80/90 wt gear oil. No leaks so far.
I also installed new brake pads and hardware front and rear. Cleaned inside of wheels.
Washed it. Test drove it and everything seemed fine.
My next task is to locate the rattle in the undercarriage and repair/or replace it.

[tbone]

Installed my new modded FPDM from RacerX. Now I can drive with confidence. Thanks Bill!

[fastblackmerc]

Today: I replaced the rear axle seals and for some reason the driver's side axle has too much end play. The right side is good. Does anyone else have this problem? Installed 8oz of Motorcraft friction modifier and just under 2 quarts of 80/90 wt gear oil. No leaks so far.
I also installed new brake pads and hardware front and rear. Cleaned inside of wheels.
Washed it. Test drove it and everything seemed fine.
My next task is to locate the rattle in the undercarriage and repair/or replace it.

How do you know it has too much end play? Did you measure it? Could be the "C" clips are worn.

Ford revised the spec for the gear oil to 70W140.

[stryker]

Take the Panther to mechanic for replacing the EGR valve, bye bye "check engine" light


Enviado desde mi iPhone utilizando Tapatalk

[blkZooM]

http://uploads.tapatalk-cdn.com/20160309/c0825fac03c2f955f15e5ef4688334 f9.jpg

Installed the 5.4 and dry fitted the lower intake and JPS mid plate.


Sent from my iPhone using Tapatalk

[tbone]

Ordered up new parking brake shoes and hardware kit.

[TJCOX]

How do you know it has too much end play? Did you measure it? Could be the "C" clips are worn.

Ford revised the spec for the gear oil to 70W140.

Measured approximately 1/8 " of or .099 inches of travel.
I even switched axles and still ended up with the same results.
Never knew of the revision of the G.O.
Thanks!
Tom

[NXSBOB]

http://uploads.tapatalk-cdn.com/20160309/c0825fac03c2f955f15e5ef4688334 f9.jpg
Installed the 5.4 and dry fitted the lower intake and JPS mid plate.
I guess you are not re-using the radiator?:bigcry:

[babbage]

http://uploads.tapatalk-cdn.com/20160309/c0825fac03c2f955f15e5ef4688334 f9.jpg

Installed the 5.4 and dry fitted the lower intake and JPS mid plate.


Sent from my iPhone using Tapatalk


wow nice job so far it fits in there pretty good. do you have the 5.4 headers do they fit?

[babbage]

cleaned up a little bit changed oil with Amsoil 0w-30, 7 qts. (bought 2 - 1 gallon jugs) 6 new quarts of Mercon V

43419

need a better funel

[blkZooM]

I guess you are not re-using the radiator?:bigcry:


Lol no, I damaged it removing the engine, figured, best put the new one in after engine has been installed

And I did not use the 5.4L headers






Sent from my iPhone using Tapatalk

[Invader]

Ordered up new parking brake shoes and hardware kit.


What was your cost on that? My local Ford dealer wants like $200+ for just the shoes... FML...


Sent from my iPhone using Tapatalk

[fastblackmerc]

What was your cost on that? My local Ford dealer wants like $200+ for just the shoes... FML...


Sent from my iPhone using Tapatalk

Hint - Rock Auto Parts.....

[Invader]

Hint - Rock Auto Parts.....


I'll check them out... Thanks...


Sent from my iPhone using Tapatalk

[Blackmobile]

Today: I replaced the rear axle seals and for some reason the driver's side axle has too much end play. The right side is good. Does anyone else have this problem? Installed 8oz of Motorcraft friction modifier and just under 2 quarts of 80/90 wt gear oil. No leaks so far.
I also installed new brake pads and hardware front and rear. Cleaned inside of wheels.
Washed it. Test drove it and everything seemed fine.
My next task is to locate the rattle in the undercarriage and repair/or replace it.


Just did mine and the PS bearing murdered the shaft at 190K miles.

http://www.mercurymarauder.net/gallery/data/670/medium/IMG_20160229_202453A.jpg (http://www.mercurymarauder.net/gallery/showphoto.php/photo/24698/title/rear-axles-bearings-after-188k-miles/cat/670)

http://www.mercurymarauder.net/gallery/data/670/medium/IMG_20160229_202358.jpg (http://www.mercurymarauder.net/gallery/showphoto.php/photo/24697/title/rear-axles-after-188k-miles/cat/670)

[JustRight]

Actually, these things were done in the last couple of weeks.

Cleaned the throttle body (took it off) and played with lighter return springs until I got it just perfect. The throttle is just right, now.

Took the car to XXX Performance in Pensacola and got the differential completely overhauled with bearings, axles, clutches, ring & pinion, etc.. Sorry Marty, just too far to drive with my buggered up leg. After twisting wrenches as an avid hobbyist for 46 of my years, it is always such a rare pleasure to find someone that is mechanically sharp as a tack, honest, professional and courteous to do the work I no longer care to do. The rear is super quiet now (the backlash was set perfectly) and the added bonus of fixing a problem I had yet to home in on. There was a roughness in the drivetrain through the seats that is gone now. He believes it was in the ring gear because the axle bearings weren't really bad.

It drove home like a brand new car. :):):)

[JustRight]

Installed new Ford Racing coil covers

http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/tapatalk_1456014820618_zpsvjvp h1ce.jpeg

Before:
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_155030_zpszhob6iug.jp g

After:
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_160425_zpsaxofnzzg.jp g
http://i3.photobucket.com/albums/y90/Mebot/Mobile%20Uploads/20160220_160435_zpsz4ljizvm.jp g


Can't stop the signal...

That looks very sharp!

[TJCOX]

Just did mine and the PS bearing murdered the shaft at 190K miles.

http://www.mercurymarauder.net/gallery/data/670/medium/IMG_20160229_202453A.jpg (http://www.mercurymarauder.net/gallery/showphoto.php/photo/24698/title/rear-axles-bearings-after-188k-miles/cat/670)

http://www.mercurymarauder.net/gallery/data/670/medium/IMG_20160229_202358.jpg (http://www.mercurymarauder.net/gallery/showphoto.php/photo/24697/title/rear-axles-after-188k-miles/cat/670)

Thanks for picture Blackmobile. My bearing and axle shaft look really good in comparsion to yours.
Tom

[tbone]

Switched to Castrol extended service oil and Mobil 1 extended service filter. I only change it once a year now, low miles driven, but hey, the oil was on sale and the filter filters out the tiniest particles of anything on the market. Double capacity too. That makes me feel fuzzy.

Emptied Musclemerc's catch can. Works like a champ.

[james79stang]

Replaced my alternator because it had a diode problem for the last year or so but finally effected the battery, I guess not to bad for over 271k.

Replaced the power lead to the video camera.

[lji372]

Did some hid projector fitment testing, all looked good.

Limited360 should be about ready to roll, feel free to fill his pm box :wave: James :P

[Red Rum]

Detailed my car inside and out. Waterless wash her with CroftgateUSA. It is the best stuff out right now. And cleaned the leather with CroftgateUSA. Com Leather cleaner and conditioner. There nice and smooth now. I was advised all of you to try it out. Best stuff on the market now.

[daddyusmaximus]

Installed my JL Audio sub enclosure today. Odd shaped thing designed for another vehicle. Got it on sale at a car audio shop going out of business. Contains a down firing 12W3-D4. It sounded great in my old 99 CVPI. Welded bolts to the trunk floor, and bolted her in. New amp goes in Wed, can't wait.



http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/019_zpsqmcrv1vd.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/019_zpsqmcrv1vd.jpg.html)

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/012_zpsyw5f2hso.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/012_zpsyw5f2hso.jpg.html)

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/021_zpsqaqunlrf.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/021_zpsqaqunlrf.jpg.html)

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/022_zpsldwvlz7g.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/022_zpsldwvlz7g.jpg.html)

[Turbov6Bryan]

Took my marauder to BP gas station. Pulled in like a boss, took two spots up for free vacuum

Reinstalled summer marauder floor mats and pulled out, didn't buy gas or a car wash

I was bored

[Gerry24]

Took her out went to the bank, filled up her tank and that's all she wrote.

[01BADMERC]

Some fresh paint..

[cer0413]

A member here started my timing cover swap for me.
From this:
http://uploads.tapatalk-cdn.com/20160316/79658b0c9a01755449e4383ab1c7d9 c3.jpg
To this:
http://uploads.tapatalk-cdn.com/20160316/d07425867f30a6f69a1ca29b2b8198 35.jpg

[daddyusmaximus]

Went and got the rest of the stereo put in. JL Audio C3 525s in the doors, C3 570s in the rear deck, and a JL Audio XD700/5v2 amp mounted on the sub enclosure. System sound great and I'm happy.


http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/car%20in%20stereo%20shop_zpszt ilyagi.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/car%20in%20stereo%20shop_zpszt ilyagi.jpg.html)

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/Amp%20mounted_zpsvdyq9koa.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/Amp%20mounted_zpsvdyq9koa.jpg. html)

[fastblackmerc]

1998 Ford Ranger

Dropped the dash to R&R the blend door actuator, took about 3 hours start to finish. Unfortunately that didn't fix the problem. Will be replacing the actual blend door tonight due to a broken shaft.

[01BADMERC]

New spring touch up..Complete.

Sent from my SM-G900V using Tapatalk

[Homeskillet43]

Really nice touch up job.

Sent from my SM-N900V using Tapatalk

[loud2004marquis]

Installed QA1 rear shocks:



http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04235.jpg

Along with PVD widened rear wheels, with a fresh set of Nitto NT555:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04244.jpg

PVD front wheels with Nitto Motivos:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04246.jpg

[cer0413]

Installed QA1 rear shocks:



http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04235.jpg

Along with PVD widened rear wheels, with a fresh set of Nitto NT555:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04244.jpg

PVD front wheels with Nitto Motivos:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04246.jpg
Why you sneaky little debil you. [emoji106] [emoji106] [emoji106]

[daddyusmaximus]

Let us know how the QA1s handle. How much did you widen the wheels and what size tires did you put on them?

Sent from my SM-N910V using Tapatalk

[MOTOWN]

Installed QA1 rear shocks:



http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04235.jpg

Along with PVD widened rear wheels, with a fresh set of Nitto NT555:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04244.jpg

PVD front wheels with Nitto Motivos:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04246.jpg

Looks outstanding Brian!

[Turbov6Bryan]

Swapped rear bumper with a nicer one, been putting it off.

Gotta polish it out, just not happy with it

[slickster]

^^^ looks great!!!! Nice job

[champ1173]

Made my MM faster and lighter today. How? By taking out about 120pnds in kitty litter from the trunk! :)

[loud2004marquis]

How much did you widen the wheels and what size tires did you put on them?

Wheels were widened to 9.5" (295/45/18)

[RubberCtyRauder]

Wheels were widened to 9.5" (295/45/18)

That's just the rear wheels dadyusmaximus. Front are still 18x 8

[lji372]

Installed QA1 rear shocks:



http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04235.jpg

Along with PVD widened rear wheels, with a fresh set of Nitto NT555:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04244.jpg

PVD front wheels with Nitto Motivos:

http://i1233.photobucket.com/albums/ff392/loud2004marquis/DSC04246.jpg

:drool:
Looking good!!!!


Looks like my new black chrome wheels will be going on Whipple car!

[chief455]

:drool:
Looking good!!!!


Looks like my new black chrome wheels will be going on Whipple car!
Agreed his car looks killer!
And your wheels will also on the black Whipple monster! :bows:

[JustRight]

The Marauder wears the widened rear wheels well. Looks great.

[JustRight]

I've been looking for some projector led bulbs for the back up lights that would fit and be quite bright. Found them----installed last light. They light up the world I couldn't see well with the aftermarket tint.

Here is the link: http://www.ebay.com/itm/331052340354?_trksid=p2060353. m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

[fastblackmerc]

I've been looking for some projector led bulbs for the back up lights that would fit and be quite bright. Found them----installed last light. They light up the world I couldn't see well with the aftermarket tint.

Here is the link: http://www.ebay.com/itm/331052340354?_trksid=p2060353. m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

Bet my 15W HIDs are brighter..... :D

[daddyusmaximus]

They make HIDS and projectors for back up lights? I feel my next upgrade coming on.

Sent from my SM-N910V using Tapatalk

[slickster]

Bet my 15W HIDs are brighter..... :D

How much??

[fastblackmerc]

How much??

I try to get some pictures of incandescent, LED and HID.

[fastblackmerc]

After the blend door actuator didn't fix the constant heat issue, I had to replace the actual blend door. Not too bad, about 3 hours, had to drop the dash - 6 bolts & 2 screws, remove the blend door actuator - 3 screws, cut open the bottom of the HVAC box - had to remove the passenger side seat for more room - too much pasta.......

Works perfectly. New door has an aluminum socket so it shouldn't happen ever again.

[tbone]

Scared my wife driving it with her. The tires always break loose when I hit second and it jerked sideways a bit around a slight curve. I Love it. She doesn't. ;(

[fastblackmerc]

Scared my wife driving it with her. The tires always break loose when I hit second and it jerked sideways a bit around a slight curve. I Love it. She doesn't. ;(

They never do................... Especially when you do it in her car.... :eek::eek: :D

[justbob]

They never do................... Especially when you do it in her car.... :eek::eek: :D


Truth!


Sent from my iThrone using Tapatalk

[lji372]

Drove it to work, made button blanks for cop covers. Drove it to the show with wifey and boosted my way home!! Great day :banana2:

[Gerry24]

Took her out to stretch a little, went to the boneyard to find some pieces for my Vic. It was a nice cool day down here so it was a fun ride.

[JustRight]

The used-to-be black Marauder is a very nice shade of solid yellow now. I'll sure be glad when this thick pollen goes away. I've got a basket full of things to do to the new ol' girl and a lot of spring projects to do. At least I'll be able to stop aggravating folks on this forum for a while. :rolleyes:

[babbage]

Got (4) new 245 55 18 - Firehawk wide ovals and a carfixer alignment.

http://www.tirerack.com/images/tires/firestone/fs_fhwo_as_w_pdpcrop.jpg

[Baconbit]

Bought her a new set of rear control arms!!

[Curless]

Bought her a new set of rear control arms!!


Woo Hoo! Now get em installed in time for Louisville!

[daddyusmaximus]

I introduced the Marauder to a guy. He complimented me on it at Auto Zone thinking it was a customized MGM. He had never heard of the Marauder.


Sent from my SM-N910V using Tapatalk

[lji372]

Agreed his car looks killer!
And your wheels will also on the black Whipple monster! :bows:


What the heck here we go!!

Still need to nightshade the tail lights.

Done by Detroit wheel. (Ask for B, tell him I sent you)

http://uploads.tapatalk-cdn.com/20160323/b9944398adc2a2287e8ae9ee723c2a b9.jpghttp://uploads.tapatalk-cdn.com/20160323/9b4dc5193b9f4faaba47e19d2089c7 1d.jpghttp://uploads.tapatalk-cdn.com/20160323/d04fcf21a633f2841b0192f8313e4b 92.jpghttp://uploads.tapatalk-cdn.com/20160323/db6687a07a8c16e39e5ef8138184c4 b0.jpghttp://uploads.tapatalk-cdn.com/20160323/5594ac1e8b6fc1fe163e112c94d13c 1b.jpg

And these are on the kids car (Cal chrome).

http://uploads.tapatalk-cdn.com/20160323/c01000701abbf587f84d6f6fecffa5 39.jpg


Sent from my iPad using Tapatalk

[WPG_Merc]

:drool::drool: looks Awesome Jerry :2thumbs:
Soon,I got to get a pair of widen rims too.:)

[lji372]

:drool::drool: looks Awesome Jerry :2thumbs:
Soon,I got to get a pair of widen rims too.:)

Gordon, I have a set ready to go buddy :beatnik:

[WPG_Merc]

cool
Marty was saying for the widen rims & 305/45R18 tires the top Rear shock mounts may have to be moved in by 2 inches.:eek:

[8UWITH6]

Jerry, you need to smack the tire tech that wrote on the sidewall of your tire. SMH.

Oh by the way it looks killer.

[WPG_Merc]

Gordon, I have a set ready to go buddy :beatnik:

How much would a pair go for

[lji372]

cool
Marty was saying for the widen rims & 305/45R18 tires the top Rear shock mounts may have to be moved in by 2 inches.:eek:


Nope



How much would a pair go for

With or without Pvd? Pm me

[daddyusmaximus]

Those darkened wheels look sharp.

I got my new-in-box factory spoiler in for the car, and dropped it off for paint.

[ctrlraven]

Started the Marauder up after it has been sitting for well over 3 months.

I was extremely shocked it started up on the first turn of the key without needing a jump or battery being charged. After about 45-60 seconds the idle smoothed out and just purred. Oh how I have missed that sweet sounding exhaust.

I did have to kill 3 large ass spiders who must of been calling the MM home for a while, one was inside the cabin and the other two were in the engine bay.

[JustRight]

The new back tires worked out so well, I took in it yesterday to get the fronts changed. The fronts were almost new Eagle Gt-s but bounced until they warmed up and made the steering very touchy at speed. With the four new tires and the second tank of Techron smoothing out the fuel system, this car is becoming an absolute pleasure to drive. I've found myself taking it everywhere now.

Took my wife's car (I used to think it was comfortable) in to fill the tank up yesterday. I couldn't wait to get back into the MM.

Also, got the factory replacement fog lights in. The originals were clouded up.

[daddyusmaximus]

The new back tires worked out so well, I took in it yesterday to get the fronts changed. The fronts were almost new Eagle Gt-s but bounced until they warmed up and made the steering very touchy at speed. With the four new tires and the second tank of Techron smoothing out the fuel system, this car is becoming an absolute pleasure to drive. I've found myself taking it everywhere now.

Took my wife's car (I used to think it was comfortable) in to fill the tank up yesterday. I couldn't wait to get back into the MM.

Also, got the factory replacement fog lights in. The originals were clouded up.

I feel the same way about mine. After driving 4x4 trucks for the last 20 years, this car has me spoiled. I still want another 4x4 for weekend fun, but I'm getting old and comfort is king...

[slickster]

Put it on my mod

[01BADMERC]

Took out of storage today and given a fresh tune up.

http://uploads.tapatalk-cdn.com/20160327/5e2691639d8f2cd5161363b143cc06 19.jpg

Sent from Droid Turbo 2 using Taptalk

[JustRight]

My rear bumper cover has the same side wrinkle. I assume it's normal?

[01BADMERC]

My rear bumper cover has the same side wrinkle. I assume it's normal?


No wrinkle..Just the way the light is hitting it but i will be checking on that tomorrow.

[01BADMERC]

Here it is at a little different angle.

.http://uploads.tapatalk-cdn.com/20160327/59f38c0c05e35f0f9549e4bc948b47 a2.jpg

Sent from Droid Turbo 2 using Taptalk

[Blackmobile]

Just got Lemonade back on the road after the belt jumped during a torrential rain storm last Thursday. Saw the temp rise to 240 and battery volts down to 10V. Drained quite a bit of water out of both sides of the inter-cooler piping. Got lucky, it still runs.

[cer0413]

Just got Lemonade back on the road after the belt jumped during a torrential rain storm last Thursday. Saw the temp rise to 240 and battery volts down to 10V. Drained quite a bit of water out of both sides of the inter-cooler piping. Got lucky, it still runs.
How's fruit punch?

[Blackmobile]

How's fruit punch?

Still shining and under a cover in the garage, where it needed to be.

[lji372]

Test fit projector fog lamps

http://uploads.tapatalk-cdn.com/20160327/cfd6b90ca56595aa68f02fee7c56c5 9d.jpg
http://uploads.tapatalk-cdn.com/20160327/937817df9d881d3446751634c4011f 6b.jpg


Sent from my iPhone using Tapatal

[Gerry24]

Took the MM out, she hasn't seen rain in awhile. Also, changed the belt in my 02 Crown Vic.

[cer0413]

Test fit projector fog lamps

http://uploads.tapatalk-cdn.com/20160327/cfd6b90ca56595aa68f02fee7c56c5 9d.jpg
http://uploads.tapatalk-cdn.com/20160327/937817df9d881d3446751634c4011f 6b.jpg


Sent from my iPhone using Tapatal
Mmmmm, urine colored projectors.

[justbob]

Mmmmm, urine colored projectors.


If you work at Fermilab! [emoji15]


Sent from my iThrone using Tapatalk

[guspech750]

Mmmmm, urine colored projectors.


LMMFAO


Sent from The White House on taxpayers dimes.

[fastblackmerc]

Had a member drop off his '03 black MM for EATC & LCM repairs and + & - cable upgrade.

[daddyusmaximus]

Paint shop called. My spoiler is painted so I got it on today. Car looks more like what I imagined a Marauder should look like... except dirty.

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg.html )

[Gerry24]

Paint shop called. My spoiler is painted so I got it on today. Car looks more like what I imagined a Marauder should look like... except dirty.

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg.html )

Looks good

[lji372]

Paint shop called. My spoiler is painted so I got it on today. Car looks more like what I imagined a Marauder should look like... except dirty.

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg.html )

Spill the beans... Cost on spoiler and paint?

[daddyusmaximus]

Spill the beans... Cost on spoiler and paint?
Too much. I wasn't sure about the aftermarket ones, but I found a factory original one on ebay, for $350. Paint and instalation was another $200.

Sent from my SM-N910V using Tapatalk

[lji372]

Too much. I wasn't sure about the aftermarket ones, but I found a factory original one on ebay, for $350. Paint and instalation was another $200.

Sent from my SM-N910V using Tapatalk

Ouch! Should have asked buddy.

A friend had an aftermarket and you couldn't tell the difference. Bought it painted off eBay for $250.

I'm about to do the same.

[01BADMERC]

Ouch! Should have asked buddy.

A friend had an aftermarket and you couldn't tell the difference. Bought it painted off eBay for $250.

I'm about to do the same.
Is there a website for that? I just need it primed. Can shoot it myself.

Sent from Droid Turbo 2 using Taptalk

[justbob]

Paint shop called. My spoiler is painted so I got it on today. Car looks more like what I imagined a Marauder should look like... except dirty.

http://i219.photobucket.com/albums/cc306/daddyusmaximus/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg (http://s219.photobucket.com/user/daddyusmaximus/media/cars/Spoiler%20from%20rear%20right% 20quarter_zps8ftlzrxq.jpg.html )


Now just get taller back tires. [emoji4]



Sent from my iThrone using Tapatalk

[daddyusmaximus]

She came with 235/50s on all 4 corners. She will get new tires this summer.

Sent from my SM-N910V using Tapatalk

[Logizyme]

Too much. I wasn't sure about the aftermarket ones, but I found a factory original one on ebay, for $350. Paint and instalation was another $200.

Sent from my SM-N910V using Tapatalk

Brand new spoilers are still available from Ford to the tune of $220.

http://accessories.ford.com/spoiler-primed.html

[daddyusmaximus]

This was the only one I could find.

http://fordofkirkland-fordparts.com/product/Crown%20Victoria/2006/Body%20Style/Rear%20Spoiler

Tried to contact them, not available. Both of those are "Ford" parts. The one I found has the Mercury waterfall logo on it by the part number so I went for it. Hell, after seeing what a damn set of Marauder floor mats, and head lights go for, I just figured that these things are limited enough that pretty much anything Marauder specific is gonna cost.

[Limited360]

This was the only one I could find.

http://fordofkirkland-fordparts.com/product/Crown%20Victoria/2006/Body%20Style/Rear%20Spoiler

Tried to contact them, not available. Both of those are "Ford" parts. The one I found has the Mercury waterfall logo on it by the part number so I went for it. Hell, after seeing what a damn set of Marauder floor mats, and head lights go for, I just figured that these things are limited enough that pretty much anything Marauder specific is gonna cost.

This is the one I used, I had two different Marauders.. both in black... so I have bought this twice, happy both times.

Primed / Painted / Ready for install for $250 shipped.

http://www.ebay.com/itm/Ford-Crown-Victoria-1998-2011-Lip-Mnt-Factory-Style-Painted-Lip-Mnt-Rear-Spoiler-/151280977303?fits=Model%3AMara uder&hash=item23390c8597:m:mxln2gcl-2nR9deRLY2umLA&vxp=mtr

[daddyusmaximus]

I guess I'll know the next time...

[Mr. Man]

Picked up a new set of wiper arms and a cowl. Forgot to get push buttons so I'll get them tomorrow along with a set of new wipers.

[RubberCtyRauder]

http://i637.photobucket.com/albums/uu92/mdnos/project_zpstcwmdsc6.gif

[Zim Hosein]

Replaced the bulbs on my factory Oil & Volt meters using 168 Sylvania bulbs. Took me about an hour and a half, what a PITA I must say! :mad:

[MOTOWN]

http://i637.photobucket.com/albums/uu92/mdnos/project_zpstcwmdsc6.gif

Lmao! That about sums it up! :bigcry:

[a_d_a_m]

Heinous control arms installed on the back, KYBs installed on the front, alignment.

It feels like a new car!

[fastblackmerc]

Replaced the bulbs on my factory Oil & Volt meters using 168 Sylvania bulbs. Took me about an hour and a half, what a PITA I must say! :mad:

Did you notice the burn marks on the top of the gauges? :eek:

Should have gone with LEDs. :banana2:

[slickster]

Replaced the bulbs on my factory Oil & Volt meters using 168 Sylvania bulbs. Took me about an hour and a half, what a PITA I must say! :mad:

I bet now you can do it in 5min with one hand;)

[tbone]

Installed a new shift linkage cable.
Adjusted slack in the emergency brake cable. Sooo much stronger now.

[lji372]

Thought about it.... Worked 14 hours so I could get ahead and spend Sunday with one (it's not supposed to rain, winning!)

[Zim Hosein]

Did you notice the burn marks on the top of the gauges? :eek:

Should have gone with LEDs. :banana2:

I did notice some slight "yellowing" on the top of my factory gauges fastblackmerc, but I thought that LED's would only work w/ aftermarket gauges, was I mistaken? :confused:

Thanks in advance for your input! :beer:

[Zim Hosein]

I bet now you can do it in 5min with one hand;)

Honestly slickster, I could cut the time down a "bit," but there is no way one can replace both bulbs on factory gauges in under an hour considering how careful one has to be w/ removing the gauge pod bracket, backing off the bolts holding the gauges in place for access to the bulbs using a deep well socket, transferring the blue bulb rubber "condoms" to the replacement bulbs and finally reversing the process, all at the same time ensuring one does not damage any of the surrounding trim. :confused:

[MOTOWN]

Honestly slickster, I could cut the time down a "bit," but there is no way one can replace both bulbs on factory gauges in under an hour considering how careful one has to be w/ removing the gauge pod bracket, backing off the bolts holding the gauges in place for access to the bulbs using a deep well socket, transferring the blue bulb rubber "condoms" to the replacement bulbs and finally reversing the process, all at the same time ensuring one does not damage any of the surrounding trim. :confused:

That job can be done in 10 to 15 minutes.

[fastblackmerc]

I did notice some slight "yellowing" on the top of my factory gauges fastblackmerc, but I thought that LED's would only work w/ aftermarket gauges, was I mistaken? :confused:

Thanks in advance for your input! :beer:

Yes you where mistaken.

LEDs will replace incandescent bulbs anywhere. They are also dimmable. If you used green LEDs you could have gone naked.... no condoms needed! :eek:

[fastblackmerc]

Honestly slickster, I could cut the time down a "bit," but there is no way one can replace both bulbs on factory gauges in under an hour considering how careful one has to be w/ removing the gauge pod bracket, backing off the bolts holding the gauges in place for access to the bulbs using a deep well socket, transferring the blue bulb rubber "condoms" to the replacement bulbs and finally reversing the process, all at the same time ensuring one does not damage any of the surrounding trim. :confused:


That job can be done in 10 to 15 minutes.

Frankly the hardest part is pulling the pod out...... you can do it with your eyes closed... 10 minutes tops.

[lji372]

Prepping.....

http://uploads.tapatalk-cdn.com/20160402/cde638c13618243d842413906e8258 09.jpg


Sent from my iPhone using Tapatalk

[slickster]

Prepping.....

http://uploads.tapatalk-cdn.com/20160402/cde638c13618243d842413906e8258 09.jpg


Sent from my iPhone using Tapatalk

Button caps?

[lji372]

Button caps?

Floating center caps

Buttons are at post 191 of the thread below

http://www.mercurymarauder.net/forums/showthread.php?t=100108&page=13

[BUCKWHEAT]

First night of the season at the drags, ran 12.1 at 115.6. Line lock solenoid was acting up. four runs & a good night!

[MOTOWN]

Finished installing Derale Transmission , and power steering coolers , deleted factory setup.

http://i1020.photobucket.com/albums/af324/sims36/20160402_155827_zpsswdlyrwe.jp g

[Baconbit]

Installed the new CHE control arms, Addco sway bar end links and changed the oil for Louisville!

[slickster]

Finished installing Derale Transmission , and power steering coolers , deleted factory setup.

http://i1020.photobucket.com/albums/af324/sims36/20160402_155827_zpsswdlyrwe.jp g

Any change in readings

[MOTOWN]

Any change in readings

Oh yeah! Went from 190* to 151* , I've got to install the transmission thermostat to get it up to operating temperature, new stat opens at 165*

[Turbov6Bryan]

Did a 2 minute video of my dad in his silver birch, loaded it to YouTube and its sideways. SMH

Guess I need to buy a go pro

[merc]

New wheels and tires

http://www.mercurymarauder.net/gallery/showfull.php?photo=24712

[MOTOWN]

New wheels and tires

http://www.mercurymarauder.net/gallery/showfull.php?photo=24712

Looks good! :coolman:

[cer0413]

Tow'd to its temporary resting place until the engine and installer is ready. [emoji36]
http://uploads.tapatalk-cdn.com/20160405/17a58ac89bcf93ad838711bfced8d1 54.jpg