PDA

View Full Version : How much PSI are you running?



bawazir
02-19-2010, 06:38 PM
Hi guys how much PSI are you running with your S/C?

ImpalaSlayer
02-19-2010, 06:39 PM
fo teen peesaye yo!

bawazir
02-19-2010, 06:41 PM
fo teen peesaye yo!

Damn is in that too much?>

RR|Suki
02-19-2010, 06:41 PM
I run 9 PSI

ImpalaSlayer
02-19-2010, 06:42 PM
Damn is in that too much?>


uhhh its a little high yes. your eaton swapping correct? run a 3.4 upper and a +2 lower.

bawazir
02-19-2010, 06:47 PM
uhhh its a little high yes. your eaton swapping correct? run a 3.4 upper and a +2 lower.


I am doing +2 ib Crank Pulley & 3.0 Ring from METCO i think that would around 11 to 12 psi, is that about right?

ImpalaSlayer
02-19-2010, 06:56 PM
I am doing +2 ib Crank Pulley & 3.0 Ring from METCO i think that would around 11 to 12 psi, is that about right?

umm no you will be 14+ psi

im running a +2 with a 3.1

bawazir
02-19-2010, 07:06 PM
umm no you will be 14+ psi

im running a +2 with a 3.1


? ohh okay well Zack told me am going to be somewere between 11 or 12 with those kit

ImpalaSlayer
02-19-2010, 07:08 PM
? ohh okay well Zack told me am going to be somewere between 11 or 12 with those kit

im just telling you what i have and what you ordered are basically the same and i made 14psi on the dyno. another member witht he same size upper and a +4 lower made 16psi so the numbers seem accurate.

-Matt-
02-19-2010, 07:09 PM
over 9000........

tjl006
02-19-2010, 07:29 PM
12 psi stock upper and +4lb lower

DOOM
02-19-2010, 07:29 PM
Currently 13psi
retune will be 15-16psi

ImpalaSlayer
02-19-2010, 07:33 PM
12 psi stock upper and +4lb lower

you went to a stock upper? i thought you went 3.4

if you did, hows hood clearance?

tjl006
02-19-2010, 07:38 PM
you went to a stock upper? i thought you went 3.4

if you did, hows hood clearance?
Got stock eaton pulley for cheap hood clearance is fine but I dont have the under hood insulator on the car

ImpalaSlayer
02-19-2010, 07:40 PM
Got stock eaton pulley for cheap hood clearance is fine but I dont have the under hood insulator on the car

ahh good to know. i too removed the liner, looked crappy anyway.

Georges93LX
02-19-2010, 07:49 PM
15psi on a 2V. oh wait that's not a Marauder.

Spectragod
02-19-2010, 07:50 PM
9 PSI, stock bottom end.

bawazir
02-19-2010, 07:52 PM
what is the recommended psi?

ImpalaSlayer
02-19-2010, 07:52 PM
what is the recommended psi?

significantly lower than 9000......

-Matt-
02-19-2010, 07:58 PM
significantly lower than 9000......


No must be over 9000


http://piratesoft.org/images/9000/over9000-4.jpg

bawazir
02-19-2010, 08:12 PM
No must be over 9000


http://piratesoft.org/images/9000/over9000-4.jpg


HA HA your fu**ing funny

Kennyrauder
02-19-2010, 09:04 PM
I am running a Vortech with a Lidio Tune 8 PSI for 91 octane. Long live my engine.Hope you are prepared for a fairly short life with your engine. I make 425 RWHP. If you want more be prepared to to pay the price if you plan on racing your Marauder a lot.

-Matt-
02-19-2010, 09:08 PM
I am running a Vortech with a Lidio Tune 8 PSI for 91 octane. Long live my engine.Hope you are prepared for a fairly short life with your engine. I make 425 RWHP. If you want more be prepared to to pay the price if you plan on racing your Marauder a lot.

Explain a little more, what happened? 8psi on a centri doesnt sound like a whole lot

ImpalaSlayer
02-19-2010, 09:09 PM
Explain a little more, what happened? 8psi on a centri doesnt sound like a whole lot

he is saying his engine is going to last for a long time because its only at 8psi. at least i think thats what he meant

Dark_Knight7096
02-19-2010, 09:10 PM
13.5 psi

(this text added to comply with post length requirements)

-Matt-
02-19-2010, 09:14 PM
he is saying his engine is going to last for a long time because its only at 8psi. at least i think thats what he meant


Ohhh..... i see what you did there

justbob
02-19-2010, 11:11 PM
In this cold air 12 Psi.

CRUZTAKER
02-20-2010, 06:42 AM
Hi guys how much PSI are you running with your S/C?

14-15 or so.

Pops
02-20-2010, 06:50 AM
Only 19 pounds.

FordNut
02-20-2010, 07:13 AM
16-18 depending on outside air temperature.

bawazir
02-20-2010, 08:15 AM
16-18 depending on outside air temperature.

16 - 18 psi! Damn you really pushing it.
Is that on a stock engine?????:confused:

RR|Suki
02-20-2010, 08:22 AM
Explain a little more, what happened? 8psi on a centri doesnt sound like a whole lot

Depends on the cfm of the centri and how freely your motor is breathing. I make 520+whp on 9 psi.

FordNut
02-20-2010, 08:29 AM
16 - 18 psi! Damn you really pushing it.
Is that on a stock engine?????:confused:

Big bore stroker, about $18k in the engine. I could probably run 25 psi but would need to use race gas.

Zack
02-20-2010, 08:37 AM
Bawazir is beginning to become another Motorhead.
He calls me, I answer the question.....then right to the internet to ask it all over again and get 50 different answers.

:rolleyes:

Pops
02-20-2010, 08:38 AM
This is not new Zack. He started with day one!:shake:

bawazir
02-20-2010, 08:53 AM
sorry guys i was just bored

Zack
02-20-2010, 09:05 AM
sorry guys i was just bored

Then ********** or do something useful! :puke:

justbob
02-20-2010, 09:39 AM
Hey Zack, What is the torque value of the intake hose clamp?

ImpalaSlayer
02-20-2010, 09:44 AM
Hey Zack, What is the torque value of the intake hose clamp?

over 9000.

justbob
02-20-2010, 09:49 AM
Crap! My torque wrench will NEVER go that high! What do I need to do?

Kennyrauder
02-20-2010, 10:49 AM
Insanity is lurking everywhere... and a whole lot of good humor... Could we use a left handed Henway to multiply the torque multiplier that is already on his wrench???Would it fit while the hood is closed???

blazen71
02-20-2010, 01:26 PM
12 psi on stock engine. No KABOOM yet!

burt ragio
02-20-2010, 03:18 PM
I plan on running a 2lb lower stock upper. Maybe 9 psi. About a 1/3 way there.

johnnyrauder
02-20-2010, 04:55 PM
12.5 v3 DR set up

courtmarshall
02-20-2010, 05:02 PM
18 here, hard to look down when really getting into it.

SC Cheesehead
02-20-2010, 05:05 PM
Insanity is lurking everywhere... and a whole lot of good humor... Could we use a left handed Henway to multiply the torque multiplier that is already on his wrench???Would it fit while the hood is closed???

English or metric?

bob6364
02-20-2010, 05:06 PM
Bawazir is beginning to become another Motorhead.
He calls me, I answer the question.....then right to the internet to ask it all over again and get 50 different answers.

:rolleyes:

LOL....Zack there was a time when I thought you where feeding him questions to ask that would get the folks here crazy...he seems to be able to ask every question that has been debated to death here.....just a natural talent to raise hair I guess.

bawazir
02-20-2010, 06:11 PM
i was just booooooooooord bob

lastdaze04
02-20-2010, 10:20 PM
11-11.5 boost
432hp-416lbs tq
Stock Trilogy with a 3.2 pulley
Rick

bigmerc'03
02-20-2010, 11:03 PM
8.5
at 434hp 390tq

Local Boy
02-21-2010, 12:53 AM
10lbs...and a whole lotta SEXY...

Aloha

martyo
02-21-2010, 02:26 AM
All of it!!!!!

MarauderTJA
02-21-2010, 07:41 AM
16 -18 lbs of boost. Nothing like boost:P.

MarauderTJA
02-21-2010, 07:43 AM
All of it!!!!!

And more if you could, you,,,, you boost junky:lol: