I need some help with a picture

[LeoVampire]

Yesterday I was @ a friends house repairing his 1970 Chevelle.

He is a painter so I also asked him to do the lettering in the new Door Sill plates I had bought for the Marauder this year.

He had a question about where they were actualy going to sit in the car.

While we were checking out the front door sill area I noticed some silver duct tape over my fuse block and seeing I had never open it before I thought it was strange so too a closer look. And then this is what I found in that area.

19512

It looks like somone cut away a piece of my lower dash and it no longer meets the panel comming up from the door sill plates.

Can someone or several please take a picture of this area so I can see for sure this is not a part of my imagination? The e-brake release is just to the right of it.

If someone @ the body shop did this I want to come @ them with proof that this is not the way the car hit thier door step.

[LeoVampire]

I had planed to take her to the Progressive center tomarrow to have the new door switch planel replaced that came in.

I had to wait till the Federal Jury duty thing was over to do this.

But I don't want to go to them and adress this without picture proof that this is not normal so I have some ground to stand on with them.

Other wise I would not have botherd you guys with the issue. I don't see any reason why someone would need to do this replacing a door?!

[ImpalaSlayer]

hang tight, ill get you a pic

[LeoVampire]

hang tight, ill get you a pic


Cool and thanks

[ImpalaSlayer]

appears mine is the same, i havent ever noticed this either

http://i2.photobucket.com/albums/y47/blaster250cr/IMG_1238.jpg

[LeoVampire]

If it haddn't been for the fact they put duct tape over my fuse box pannel I never would have noticed it!

Thanks for the picture ImpalaSlayer you kind of saved me from a unjustified blow up with them!

Man I was ready to kick some butt!

[ImpalaSlayer]

If it haddn't been for the fact they put duct tape over my fuse box pannel I never would have noticed it!

Thanks for the picture ImpalaSlayer you kind of saved me from a unjustified blow up with them!

Man I was ready to kick some butt!

np, it is kinda weird that they didnt make one the the panels over lap the other. looks "unfinished"

[LeoVampire]

np, it is kinda weird that they didnt make one the the panels over lap the other. looks "unfinished"


It looks like someone took a razor knife and did a quick cut on mine and looks fresh this is why I freeked out.

[Phrog_gunner]

The plastic cover on my fuse block also has tape on it from the factory.

[ImpalaSlayer]

my pic is *****y, but it to is a very rough cut.

[LeoVampire]

The plastic cover on my fuse block also has tape on it from the factory.

With all the times I have cleaned the inside of te car I never noticed the tape nor the cut away on the dash.

Must be because of the accident on that side that I am paying so much attention to stuff now. Can't see any other reason for my noticing things now.

[musclemerc]

Well I just looked at mine Leo and it too is the same as yours. Don't panic!

[LeoVampire]

Well I just looked at mine Leo and it too is the same as yours. Don't panic!

I wasn't in a panic persay I was just ready to raise holy hell if this was done by someone other than the factory.

I did not want to do or say something without proof ahead of time so I would not feel like an idiot if it was proven to me they had nothing to do with it.

[JamesHecker]

Just another example the the high build quality of our vehicles. No detail is too small or to large to overlook!

[LeoVampire]

Just another example the the high build quality of our vehicles. No detail is too small or to large to overlook!

I am sure if we looked through every car on the market close enough we would see things like this in one spot or another.

@ least there have been no major issues with the Marauder and no major recall's. You can't say you didn't get your money's worth out of them if bought brand new.

[FordNut]

I made a small filler panel that fits in there, mounted some switches there. Line lock on/off switch, tune select rotary switch for my chip, and A/B/dyno mode switch for the transmission controller.