Log in

View Full Version : For Sale Trilogy Over-the-Blower Inlet (NEW)


Zack
10-26-2010, 01:07 PM
Got this years ago and never used it.
$175 shipped.
Comes with the TB adapter plate and Throttle bracket
SC Cheesehead
10-26-2010, 01:55 PM
Got this years ago and never used it.
$175 shipped.
Comes with the TB adapter plate and Throttle bracket


Will this bolt up to a Cobra M112?
DOOM
10-26-2010, 02:00 PM
Its not polished! :shake: :down:

:jk:
merc
10-26-2010, 02:00 PM
Will this bolt up to a Cobra M112?

I don't think so, but it will bolt up to a MP112 which I have for sale in the next couple of weeks.
FordNut
10-26-2010, 02:03 PM
No.
.........
SC Cheesehead
10-26-2010, 03:40 PM
I don't think so, but it will bolt up to a MP112 which I have for sale in the next couple of weeks.

Gotcha. As soon as I posted up, it occurred to me that the M112 has the outlet on the right rear.

BTW, you going to a Whipple?
merc
10-26-2010, 04:03 PM
Gotcha. As soon as I posted up, it occurred to me that the M112 has the outlet on the right rear.

BTW, you going to a Whipple?

I purchased the Whipple in June, thus freeing up the Trilogy blower, outlet, and adapter plate. My old car is going to be parted out in 30 days. Stay tuned for the sale.

I will start another thread because I don't want to hi-jack Zack.
Zack
10-29-2010, 06:17 AM
Here is what this inlet looks like over a KB 2.2 Blower.
If you are good at fabbing this will be cake to make the necessary piece to connect the 2.

Even if you paid someone, I dont see this as costing more than $200 to make.
RocsMerc
10-30-2010, 01:36 PM
Would you be willing to sell the throttle body adaptor plate seperatly? That's one of the pieces I'm missing.
Zack
10-30-2010, 02:25 PM
SOLD Close it down
Zack
10-30-2010, 02:26 PM
Would you be willing to sell the throttle body adaptor plate seperatly? That's one of the pieces I'm missing.

Ill trace it and mail you the template.
PM me your address
doorgunner808
11-03-2010, 05:36 PM
Thanks a bunch Zack! I was so exited about finding this piece that I didn't pay attention to the fact that you were including the adapter plate and throttle cable bracket. I pulled the inlet out of the box, ran inside and started fab'ing up my adapter. Then noticed there wasnt a place to bolt a bracket on the inlet. I've been looking for a throttle bracket for an hour and a half and was about to PM you to see if you still had one. I re-read this thread then ran out to dig in the box and found the bracket. Thanks again!! Saved me a bunch of work and heartache!!
doorgunner808
11-03-2010, 05:39 PM
Would you be willing to sell the throttle body adaptor plate seperatly? That's one of the pieces I'm missing.


I've got access to bit of sheet aluminum. I can fab up a copy and send it to you. If you're interested, PM me an offer.
tjl006
11-03-2010, 07:37 PM
Would you be willing to sell the throttle body adaptor plate seperatly? That's one of the pieces I'm missing.
What adapter plate are you looking for Roco? The part that goes from the plenum to the supercharger? I sold you that piece.
Zack
11-03-2010, 07:40 PM
I traced that piece for you RocsMerc and dropped it in the mail
Use 1/8" aluminum
RocsMerc
11-07-2010, 05:41 PM
What adapter plate are you looking for Roco? The part that goes from the plenum to the supercharger? I sold you that piece.

No, I have that piece, thank you. This is the plate that goes between the throttle body and the plenum. I think it's purpose is to seal off the idle air intake on the throttle body since trilogy has relocated it off the throttle body to it's own intake hose into the side of the plenum.