Lookin to upgrade ye ol rotors... Got a question

[4drcbra]

Ive found EBC slotted dimpled rotors. Anyone have an experience with them?

[Got_1]

alot of people don't like them but i have had them on for about 10k, 2yrs with no problems at all.

[SGT_MERC]

I used rotor pros, drilled and slotted, front and back, with ceramic pads for $240.00. I've put 8,000 miles on them with no problem. My oem rotors kept warping.

[Taemian]

Dennis Reinhart used to be a vendor for them, they screwed him over along with customers of his. Ask him what happened.

[ctrlraven]

Dennis Reinhart used to be a vendor for them, they screwed him over along with customers of his. Ask him what happened.
A lot of the rotors warped pretty quickly and EBC told DR and his customers tough luck.

I bought a set of EBC rotors and green stuff pads (their entry street pads) damned if the pads were eating into the rotors like no tomorrow. I had them turned once after 10-11k miles and then they warped again 2k miles later. I tossed them and went back to all OEM and have been fine since then.

[SID210SA]

As a suggestion....I went with PowerSlot rotors and Hawk HPS pads and love them....granted i havent used them very much...but have had them since about September.

[JBeezy]

I used rotor pros, drilled and slotted, front and back, with ceramic pads for $240.00. I've put 8,000 miles on them with no problem. My oem rotors kept warping.

Link to website please! Sounds like a good price

[SGT_MERC]

Link to website please! Sounds like a good price

http://www.rotorpros.net/
You have to fill out all the info, send it and they will send you a price with contact info. Your choice from there.

[ctrlraven]

As a suggestion....I went with PowerSlot rotors and Hawk HPS pads and love them....granted i havent used them very much...but have had them since about September.
That will be my next step with brakes is PowerSlot cryo rotors with Hawk HPS pads.

[Got_1]

A lot of the rotors warped pretty quickly and EBC told DR and his customers tough luck.

I bought a set of EBC rotors and green stuff pads (their entry street pads) damned if the pads were eating into the rotors like no tomorrow. I had them turned once after 10-11k miles and then they warped again 2k miles later. I tossed them and went back to all OEM and have been fine since then.

maybe this is why i've had good luck with them. I used OEM pads with EBC rotors.

[BLACKMARAUDER04]

I was going to go with the Cryo untill I saw the price and that I had to buy all 4 rotors. I only needed front rotors at the time of my first brake change at 113,000 miles. I went with NAPA ultra rotors. Paid $68 each locally. I used them with Ford OEM pads. Very happy with them so far. I have about 6000 miles so far and have been very satisfied with their performance.

[4drcbra]

R1 concepts had a slotted drilled rotor wirh ceramic pads for 272 bucks and thats for all 4 corners. Id prefer not to cut corners on stopping

[Yamaha]

I have them in the rear with the green pads. Work fine, wearing clean , no scoring of rotor.
PS erotor and pads on for 45K. I run the car hard and tow a 3500 lb. boat. Good luck.

[Marauderjack]

What's wrong with the OEM stuff??:confused:

I got 177K miles out of my OEM pads and rotors except for about 500 miles when I got some aftermarket ones that took 3X pedal pressure to stop...returned them and back to OEM's and as far as I know they work fine!!:beer:

[JOEMERC]

I agree ,unless your on a road coarse all the time i think oems work fine. I would stay oem.

[4drcbra]

I'm about to start doing autocross so I'd be a bit hard on braking