PDA

View Full Version : 4.10


Coupe
08-30-2011, 12:14 PM
can somebody recommend me a good 4.10 ring & pinion for my marauder?
may someone can offer me an used?
Ktorres1
08-30-2011, 12:27 PM
sparta performance i believe carrys them.
Coupe
08-30-2011, 12:42 PM
thank you,ask them, about shippiong to germany
Papillon
08-30-2011, 01:00 PM
Sparta Performance Link - https://ssl111.webhosting.optonline.ne t/spartaperformance.com/merchantmanager/advanced_search_result.php?key words=4.10&mmsid=7b7f07a21cb991e7b1f915e0 599b1d5f&x=9&y=9


You might want to PM him about any questions re: shipping to Germany though.
ctrlraven
08-30-2011, 05:32 PM
Coupe, don't you have a twinscrew s/c?
Coupe
08-30-2011, 07:54 PM
sorry, what signifies twinscrew s/c?
ctrlraven
08-31-2011, 06:37 AM
There is someone in Europe that has a Trilogy twinscrew blower. I could of sworn it was you that had it.

http://www.youtube.com/watch?v=wMpBJzqbx-c
wMpBJzqbx-c
Blackened300a
08-31-2011, 06:58 AM
Sparta shipped a Aluminator to Italy, Im sure he can ship to Germany.
Coupe
08-31-2011, 06:59 AM
no, thats not me
ctrlraven
08-31-2011, 07:18 AM
Oh ok, well if you are NA and have a tune you'll love the benefit of what 4.10's will add then.
Baconbit
09-12-2011, 09:28 AM
Ok if I buy the Ford Racing 4:10 gears do I need anything else for the install??? or just what comes in the box? How hard is it to do the swap myself? Does anything need pressed in?
Baconbit
09-12-2011, 09:56 AM
Anyone?.......
MM2004
09-12-2011, 10:13 AM
Anyone?.......

You will need the gear lube, friction modifier if the gear lube doesn't have it included. (Bottle will say LS on it if it is in there). -3 to 4 bottles.

I went ahead and bought both innner and outer pinion bearings and a pinion nut and crush washer.

That should about cover it.

Took my wrench about 2 1/2 hours to do it while my MM was on a lift. (He has done dozens of these and could do it blindfolded)

;)

Mike.
MM2004
09-12-2011, 10:19 AM
If you have never setup gears before, I would pay someone that is good with the Ford 8.8 rear-end to do it.

You will need gear paste, a tenth indicator with a magnetice mount, air tools a big help and preferably a lift.

A tube of silicone/gasket sealer, spray cleaner and a ton of shop towels.

If the back-lash is not right on the gears, you won't know it until you drive it. If the gears make noise, back apart it comes.

Mike.
JBeezy
09-12-2011, 10:28 AM
May need shims as well.
fastblackmerc
09-12-2011, 10:53 AM
Ok if I buy the Ford Racing 4:10 gears do I need anything else for the install??? or just what comes in the box? How hard is it to do the swap myself? Does anything need pressed in?

The pinion gear will have to be pressed on.

Since it's apart I'd replace all the bearings, races & seals, including the axle bearing and seals.
Baconbit
09-12-2011, 11:04 AM
So it sounds like my best bet is to take to someone...my dad is a mechanic but I doubt he would want to mess with all that...wonder what the dealer would charge...
MM2004
09-12-2011, 11:10 AM
So it sounds like my best bet is to take to someone...my dad is a mechanic but I doubt he would want to mess with all that...wonder what the dealer would charge...

Try and find a shop that the local Mustang guys go to for gear swaps.

Same rear-end as the MM -> 8.8

MIke.