Bracket bolts

[clintons4]

are these the correct bolts for the eaton brackets?

http://www.fastenal.com/web/products/detail.ex?sku=11114398&ucst=t

http://www.fastenal.com/web/products/detail.ex?sku=11114402&ucst=t

[clintons4]

C'mon....no insight on this. wow

[guspech750]

I bought 3 of each.
M8x1.25 120mm
M8x1.25 150mm

That is what I used for my swap brackets.


---
- Sent from my iPhone
Eaton Swap + 4.10's = Wreeeeeeeeeedom!!

[SC Cheesehead]

Here's the info I got from Terry G. when I received my brackets:

You will need;
8x1.25 x 25mm Hex head 3 ea. Tensioner to bracket
150mm 2 Tensioner Bracket to block
160mm 1 Tensioner Bracket to block
45mm 1 Alt. to bracket
90mm 1
All thread bolt to go through the idler, through the bracket and will become the other Alt. mount.
110mm 3 Alt. bracket to engine
1.25 washers 11

[RacerX]

I had Terry send me the right bolts recently for cheap $$$. He's Da Man!!! :beer: Just noticed my bolts are a bit different since it's the Terry bracket with extra idler.

[clintons4]

Great thanks!

[breeze]

alrighty, needed this

[bugsyc]

I bought the bolts from fastenal also.the sizes are correct however I recieved them in black...8.8....are these useable or should I reorder them in 10.9 yellow zinc as shown in post number 1 thanks...bugsy

[bugsyc]

I received the bolts from fastenal.The sizes are correct however,they are black and 8.8 ...should I reorder them in 10.9 yellow zinc as shown in post #1 ???or am I ok with what i HAVE?? T.G. maybe you can chime in,or cheesehead or racer x ????Thank you for any insights you guys may have... BTW getting real close to having ALL the swap parts...Thanks....bugsy....:co nfused: Please excuse double post,I didn't realize the first one posted.. Also,while I have your attention, the 11 washers,,,are they 1.25 outer measurements or inner (which would make them humongous)???

[RacerX]

Did you just quote yourself, then edit the quote? :D Nice one silly! You have a different bracket than I do, so, I can't help too much. Black oxide is fine. You can use painters tape over the threads or drill some holes in a block of wood, make sure the bolts are cleaned with isopropyl alcohol, paint them whatever color you want with an engine enamel.

The bolts will hold up fine. Do you know if they're 8.8? Not sure about the washers. I didn't need any with my brackets. My bolts are flat head, countersunk.

[bugsyc]

OK,let me see if I got this right...The bolts in black oxide are fine? I don't care about the color only if they will hold up and do the job...Also any answer on the washers??? 1.25 inner diameter or outer diameter..I bought the 1.25 outer diameter,as I said,the 1.25 inner diameter are HUGE...Also Thank you Racer X,I can always count on you to try and help out....Thank you....bugsy.......:bows:

[SC Cheesehead]

OK,let me see if I got this right...The bolts in black oxide are fine? I don't care about the color only if they will hold up and do the job...Also any answer on the washers??? 1.25 inner diameter or outer diameter..I bought the 1.25 outer diameter,as I said,the 1.25 inner diameter are HUGE...Also Thank you Racer X,I can always count on you to try and help out....Thank you....bugsy.......:bows:

That's gotta be OD, bugsy, which washers are they again?

[bugsyc]

The 11 1.25 washers on Terrys parts list...My main concern was that the bolts in black oxide 8.8 would do the job...I have since learned(after I bought them) that 10.9 or 12.9 would have been better....If need be I'll exchange what I have for steel 12.9's if I have to...Assuming fastenal goes for it....Funny thing is Fastenal has a store here in Myrtle Beach but,they don't carry the bigger bolts...Have to go on line...Been a while Mr.Cheesehead,when and where is the next Carolina Marauders get together???....bugsy....:) P.S. Racer X (who has generously given me help and advice)seems to feel I'll be OK with what I have...(talking bolts again)

[SC Cheesehead]

The 11 1.25 washers on Terrys parts list...My main concern was that the bolts in black oxide 8.8 would do the job...I have since learned(after I bought them) that 10.9 or 12.9 would have been better....If need be I'll exchange what I have for steel 12.9's if I have to...Assuming fastenal goes for it....Funny thing is Fastenal has a store here in Myrtle Beach but,they don't carry the bigger bolts...Have to go on line...Been a while Mr.Cheesehead,when and where is the next Carolina Marauders get together???....bugsy....:) P.S. Racer X (who has generously given me help and advice)seems to feel I'll be OK with what I have...(talking bolts again)

May 5th, Blue Oval Classic in Mooresville.

http://www.foacarolinas.com/foac_blue_oval_classic.html

[RacerX]

Tensile strength on an 8.8 bolt is 150,000psi. Per bolt. No probs. ;)

[bugsyc]

150.000 per,that should do it....Almost there....2 or 3 more parts and I'm totally,completely loaded with parts..Can't wait to floor the sucker..Go down 95 sideways...yeah...that's the ticket...ticket for real...Anyhoo,Y'all haven't heard the last of me by any means...Gonna try to make the next Carolina Marauders meet...May 5????correct Mr.Cheesehead...I'm looking foward to meetin up with you guys in person.....bugsy.....:D...:ban ana:

[tdotcv]

Are the bolts full thread or partial?

[bugsyc]

partial...i think clinton posted pictures...bugsy....:D look at post #1..

[burt ragio]

Don't forget the loctite.