headers

[bugsyc]

will these work for us? SW 03-04 cobra mach1 4.6L 4v. $890

[justbob]

If it lists for a cobra, then absolutely not. Check my thread on Cobra LT's, you see.

Besides, isn't $890 bucks the normal S.W. price will little online searching for a Marauder anyways?

[MrBluGruv]

Besides, isn't $890 bucks the normal S.W. price will little online searching for a Marauder anyways?

^this^

I don't think it'd be worth fighting headers that aren't designed specifically for the MM when ones that are designed for the car are barely more expensive.

[jmarino]

These might work. What do you guys think?

http://www.ebay.com/itm/Pacesetter-Headers-96-04-Ford-Mustang-Cobra-Mach-1-4-6L-/360375735317?pt=Motors_Car_Tru ck_Parts_Accessories&hash=item53e8115415&vxp=mtr#ht_2822wt_1185

[SC Cheesehead]

These might work. What do you guys think?

http://www.ebay.com/itm/Pacesetter-Headers-96-04-Ford-Mustang-Cobra-Mach-1-4-6L-/360375735317?pt=Motors_Car_Tru ck_Parts_Accessories&hash=item53e8115415&vxp=mtr#ht_2822wt_1185


I think they'd need to be modified to fit in a MM, prolly have some clearance issues. Keep in mind that the Cobra and MM share a similar engine, but the engine bays and component locations are different.

Justask justbob...

[justbob]

These might work. What do you guys think?

http://www.ebay.com/itm/Pacesetter-Headers-96-04-Ford-Mustang-Cobra-Mach-1-4-6L-/360375735317?pt=Motors_Car_Tru ck_Parts_Accessories&hash=item53e8115415&vxp=mtr#ht_2822wt_1185

REREAD post 2. Or dont, your choice..

[SC Cheesehead]

REREAD post 2. Or dont, your choice..

Justbob justspeaks... ;) -----> :D

[guspech750]

Justbob for the Justwin!!


Sent from my iPhone
Eaton Swap + 4.10's = Wreeeeeeeeeedom!!

[massacre]

Man if they would fit with little modification I would have these in my car by the end of the week.

But justbob has spoken....

But seriously, I can't believe that price! I wonder why so cheap? Crappy fit, crappy finish, Chinese made?

[justbob]

Could be just my 03-04 cobra MAC LT's? Maybe not? Maybe I should buy some of these and be a ginny yet again. :D Hell, I'm all set up now. ;)

My passenger side fit but headed right for the trans and made hook up "maybe doable" but definately a high heat issue. Driver side primary 1 ran dead center of the steering shaft and primary 2 hit the frame as well as heading for the trans. I rerouted primaries 1 & 2 up high. 2. Went between 3 & 4 and down and 1 went almost parallel with 4 IIRC. Then both collectors had to be super heated in the vise with two torches and moved out almost two inches and up an 1". If I did it again, I would go up even more as there is plenty of vacancy to be had.

I was looking into the pacesetters myself, but mine came ceramic coated for $450 and got better reviews from other forums. I read the pacesetters are notorious for cracked welds. My gamble didn't pay off and it was either work with what I had or lose my butt on them as I had a million scratchs from trying to get the drivers side in. I could do it all over again in one day now that I know what has to be done. Would I fab a set for a member? NOPE. You couldn't afford me.:cool:

[massacre]

Thanks for the info. Cracked welds? I don't need that. I guess I now see why they are so cheap...lol

[bugsyc]

Thanks for all the great feedback..What's the bottom line here.Which headers are made for the Marauder 1 which are the most reasonably priced 2 which require the least amount of mod work 3....I was looking and the SW's are looking good,however,they say you must buy and ofcourse use their X pipe.Which is an extra 600+dollars... So,which are the cheapest,best,easiest to install???bugsy :help:

[SC Cheesehead]

PM 03mmmonroe, IIRC, he's got SW headers on his car, and I think he has a fabbed set up from the collectors on back.

FWIW, anything you get for an exhaust system mod isn't going to be cheap, I'd budget at least $1,500 for headers, installation, mid-pipe fabrication, etc.

[justbob]

Thanks for all the great feedback..What's the bottom line here.Which headers are made for the Marauder 1 which are the most reasonably priced 2 which require the least amount of mod work 3....I was looking and the SW's are looking good,however,they say you must buy and ofcourse use their X pipe.Which is an extra 600+dollars... So,which are the cheapest,best,easiest to install???bugsy :help:

If you have a nice welder, you aren't limited to anything or anybody. :thumbup: