I need help for Whipple Project

[ali33334us]

Hello, I have a problem & I need help
I have Mercury Marauder 2003 with Trilogy motorsorts supercharger installed
I would like to buy Whipple 2.3 supercharger like you installed in your car
what are the items requirements to install whipple supercharger?
are the items available in your website?
how much do they cost?
where can I boy them?
we need your help
thanks

[DOOM]

What motor do you have in your car?

[ali33334us]

I have same motor in Mercury Marauder 2003

[Marauderman]

Hello, I have a problem & I need help
I have Mercury Marauder 2003 with Trilogy motorsorts supercharger installed
I would like to buy Whipple 2.3 supercharger like you installed in your car
what are the items requirements to install whipple supercharger?
are the items available in your website?
how much do they cost?
where can I boy them?
we need your help
thanks

COntact "CWright" -screen name-- here on the board He just completed same install on his---good luck

[martyo]

I have same motor in Mercury Marauder 2003

I would NOT recommend the Whipple 2.3 on a stock Marauder motor.

[martyo]

COntact "CWright" -screen name-- here on the board He just completed same install on his---good luck

I heard something aabout that buold.....

[ali33334us]

It is not stock engine, it is forged engine
I have Mercury Marauder engine with all installed parts:
mercury marauder 2003 supercharger trilogy motorsports
forged engine




1-ford racing 4.6 forged steel carnkshaft.model:m-6303-d46
2-manley 4.6L ford 11c dish pistons (3.572" BORE).Model: MAN-5941C8.
3-manley 4.6L ford performance piston rings (20 over).
4-manley 4.6L ford forged steel "H-peam" connecting rods.model:14042-8
5-federal mogul 4.6L ford ma-series main bearings.
6-federal mogul 4.6L tri-metal rod bearings.
7-fel-pro ford 4.6L engine gasket set.
8-fel-pro 4.6L mls head gasket lh.
9-fel-pro 4.6L mls head gasket rh.
10-ARP 4.6L carnkshaft pulley bolt.
11-ARP 4.6L cam sprocket bolt kit.
12-ford racing 4.6L dohs camshaft drive kit.
13-ford racing 96-04 mustang high volume oil pump.
14-ARP 96-04 mustang cylinder head studs.
16-ARP 96-04 mustang DOHS main studs w/Windage tray.
17-kooks headers long tube.
18-magnaflo x-pipe 2.5 inch full.
19-ford racing gear 8.8 - 373.
20- K&N kit filter ramer.
21-converter yank 3400 stall.
22-transgo 4r70w shaft kit.
23- cooler oil transmission.
24-nt555r 285/40/18.
25-nt555 extrime 255/45/18. front.
26-oil filter K&N.
27-spark NGK TR6.
28-Hypertech 96-04 Mustang 160 Degree Thermostat
29-Eibach Pro-Kit 4 coil springs
30- Accufab 03-04 Cobra Single Blade Throttle Body
31-mass air sct 3000.
32-fuel pump ford gt supercar.
33-ThumpRRR Billet Aluminum Belt Tensioner-machind saleen extension arm is desiged
34-cancel EGR fuel.
35-system nitrous nos 75 shot.

[BODYMAN]

Been running the 2.3 Whipple for over a year now.. So U say U have a trilogy kit on youre car now?

[hotford]

ya whipple it................

[martyo]

It is not stock engine, it is forged engine
I have Mercury Marauder engine with all installed parts:
mercury marauder 2003 supercharger trilogy motorsports
forged engine




1-ford racing 4.6 forged steel carnkshaft.model:m-6303-d46
2-manley 4.6L ford 11c dish pistons (3.572" BORE).Model: MAN-5941C8.
3-manley 4.6L ford performance piston rings (20 over).
4-manley 4.6L ford forged steel "H-peam" connecting rods.model:14042-8
5-federal mogul 4.6L ford ma-series main bearings.
6-federal mogul 4.6L tri-metal rod bearings.
7-fel-pro ford 4.6L engine gasket set.
8-fel-pro 4.6L mls head gasket lh.
9-fel-pro 4.6L mls head gasket rh.
10-ARP 4.6L carnkshaft pulley bolt.
11-ARP 4.6L cam sprocket bolt kit.
12-ford racing 4.6L dohs camshaft drive kit.
13-ford racing 96-04 mustang high volume oil pump.
14-ARP 96-04 mustang cylinder head studs.
16-ARP 96-04 mustang DOHS main studs w/Windage tray.
17-kooks headers long tube.
18-magnaflo x-pipe 2.5 inch full.
19-ford racing gear 8.8 - 373.
20- K&N kit filter ramer.
21-converter yank 3400 stall.
22-transgo 4r70w shaft kit.
23- cooler oil transmission.
24-nt555r 285/40/18.
25-nt555 extrime 255/45/18. front.
26-oil filter K&N.
27-spark NGK TR6.
28-Hypertech 96-04 Mustang 160 Degree Thermostat
29-Eibach Pro-Kit 4 coil springs
30- Accufab 03-04 Cobra Single Blade Throttle Body
31-mass air sct 3000.
32-fuel pump ford gt supercar.
33-ThumpRRR Billet Aluminum Belt Tensioner-machind saleen extension arm is desiged
34-cancel EGR fuel.
35-system nitrous nos 75 shot.

That is a different story.....

[CWright]

You can use most of what you have already with Trilogy kit. You will need to order a 2.3 Whipple for a 03-04 Cobra. It's not just a matter of switching superchargers and you will have to realign some pulleys, move the battery to driver side or to the trunk, along with resetting your fuse panel under the hood. We are working on adding some addtional pulleys to stop the belt slip right now. It will take some addtional modding but you already have 90% of what you will need. If you have any questions I'll be more than happy to help or point you in the right direction to get an answer.

[martyo]

You can use most of what you have already with Trilogy kit. You will need to order a 2.3 Whipple for a 03-04 Cobra. It's not just a matter of switching superchargers and you will have to realign some pulleys, move the battery to driver side or to the trunk, along with resetting your fuse panel under the hood. We are working on adding some addtional pulleys to stop the belt slip right now. It will take some addtional modding but you already have 90% of what you will need. If you have any questions I'll be more than happy to help or point you in the right direction to get an answer.

Chris, send me your salary requirements.

You make this stuff sound so easy, we are going to hire you at the shop! :D

[CWright]

Chris, send me your salary requirements.

You make this stuff sound so easy, we are going to hire you at the shop! :D


I'll get that to you ASAP! :D

[ali33334us]

You can use most of what you have already with Trilogy kit. You will need to order a 2.3 Whipple for a 03-04 Cobra. It's not just a matter of switching superchargers and you will have to realign some pulleys, move the battery to driver side or to the trunk, along with resetting your fuse panel under the hood. We are working on adding some addtional pulleys to stop the belt slip right now. It will take some addtional modding but you already have 90% of what you will need. If you have any questions I'll be more than happy to help or point you in the right direction to get an answer.

1/I would like to know, if I install outlet plate to accommodate the whipple supercharge , the hood of the engine will close normally or It will not close hood ( I mean it there any problem for hood or not)

2/what is size for snout for whipple ?

3/what is kind of filter ramir that fut my project ?

4/for throttle body cable,because in my car it is in the left side,but in whipple project it is in the right side (passenger side) is there any problem for cable or not
I need more information with details
thanks

[martyo]

1/I would like to know, if I install outlet plate to accommodate the whipple supercharge , the hood of the engine will close normally or It will not close hood ( I mean it there any problem for hood or not)

2/what is size for snout for whipple ?

3/what is kind of filter ramir that fut my project ?

4/for throttle body cable,because in my car it is in the left side,but in whipple project it is in the right side (passenger side) is there any problem for cable or not
I need more information with details
thanks

The hood will not clear the Whipple without modification. You will need to space the motor down and relieve some of the bracing on the hood or use a different hood.

Order the Whipple 2.3 set up for a '03 Cobra and it will set up in place of the Trilogy (and the standard snout length will work). You will need to move teh battery and do some relocating to fit the blower because of the opposite sided inlet on the Whipple. The throttle cable will fit with some minor modification.

I am not sure I understand your question about the filter but if you are refering to the cold air intake, we fabricated a custom intake set up that looks good and work well.

We set up Chri's car (CWRIGHT) for him and it made great power. It just takes some patience and fabrication and it will all come together.

[MOTOWN]

Im working on the patience and fabrication part! lol

[martyo]

Im working on the patience and fabrication part! lol

It'll pay off!!

[CWright]

the hood will not clear the whipple without modification. You will need to space the motor down and relieve some of the bracing on the hood or use a different hood.

Order the whipple 2.3 set up for a '03 cobra and it will set up in place of the trilogy (and the standard snout length will work). You will need to move teh battery and do some relocating to fit the blower because of the opposite sided inlet on the whipple. The throttle cable will fit with some minor modification.

I am not sure i understand your question about the filter but if you are refering to the cold air intake, we fabricated a custom intake set up that looks good and work well.

We set up chri's car (cwright) for him and it made great power. It just takes some patience and fabrication and it will all come together.


+1 ^^^^^

....