FRONT wheels and tires.

[Ari]

I always see plenty of talk about what tires to use out back for better traction and better performance in the rain, etc. What about front tires? I'm looking to run an 18x9.5 up front with wider tires to improve grip. Does anyone have any suggestions for tires to fit an 18x9.5? And does anyone have any pointers on what wheel offset to run up front with a wider wheel? I saw an 18x11 wheel covered but I'm not looking for that wide of a wheel heh. Thanks in advance guys.

Oh yeah, I'm driving a 2003 Crown Victoria p71 and I'll be running the tce 14" front brake kit.

[lji372]

I think Motown is running wide fronts.

[Krytin]

I run 255/45-18 on the front w/stock MM rims - 8" wide w/no rubs at full lock rt/lft.

[MOTOWN]

I run 20x10s all the way around, it all depends on what look your after, staggered with a rake, or same size tires all way around?

When i ran oem 18s i ran widened 18x10s up front and 18x11s on the rear

[breeze]

Fronts i have 9.5 255/45 (should go wider tire) with 40 offset no problems whatsoever.

[Ari]

I'm looking to run a wider tire up front for better grip around the turns and better bite for braking. I'll probably be running an 18x11 or so out back to put the power to the ground and I have a set of steelies that I'll throw drag radials on if I decide to hit the drag strip. Could I run a 255/45-18 on a 9.5" wide rim? It looks like the approved rim width for that size tire is anywhere from 8-10". Would that look stretched on the wheel? I'm not after the stretched look.

Krytin: What tire are you running and how do you like it?

[Krytin]

I am just getting done w/Cooper Zeon Sport RS 255/45 - 18 on all 4 corners.
3 years of daily driving & over 35k miles. Longest lasting tires since I had the car from new! Still corners very well and down to the wear bars on 3 out of 4 (#4 is about hit). Breakaway traction on the rear tires is a little less than when new but not a problem. Very happy w/these and may replace w/Cooper again - depends on what I find for price. I have also run Nitto brand in the past w/good results.
Always get the 103W load range when getting tires - a must for these cars!!

[breeze]

The tire will look stretched that's why I said should go with wider tire in post #5.

[Ari]

275/40/18? Or is that too short of a tire? I'm looking at a 265/50/18 and a 275/40/18 on nitto's nt555 line for the front. Is this even a good tire to run up front for throwing the car around the twisties?

[05crownsport]

I'm watching this closely. I am interested in running a 275-45/19 all the way around on my crown vic. The stock overall diameter is 27.2" while the larger tire I am looking at is 27.7" I'm not sure if the extra width along with the extra diameter will fit the front without rubbing.

[MOTOWN]

I'm watching this closely. I am interested in running a 275-45/19 all the way around on my crown vic. The stock overall diameter is 27.2" while the larger tire I am looking at is 27.7" I'm not sure if the extra width along with the extra diameter will fit the front without rubbing.

Shouldnt be a problem unless your car is lowered, i run a 315/35 20 on the front, which is about 28.5" tall and 12.5" wide with no rubbing at all wheel is a 20x10 on a =40mm +offset which perfect for these cars.

On your wheel and tire choice i would go 18" or 20" as odd size wheels and tires cost a bit more, and the selection isnt all that great.

[breeze]

Shouldnt be a problem unless your car is lowered, i run a 315/35 20 on the front, which is about 28.5" tall and 12.5" wide with no rubbing at all wheel is a 20x10 on a =40mm +offset which perfect for these cars.

On your wheel and tire choice i would go 18" or 20" as odd size wheels and tires cost a bit more, and the selection isnt all that great.

Great to know that that wide ass tire will fit fine. Opens up a new can of worms for with tire selections now.

[05crownsport]

Shouldnt be a problem unless your car is lowered, i run a 315/35 20 on the front, which is about 28.5" tall and 12.5" wide with no rubbing at all wheel is a 20x10 on a =40mm +offset which perfect for these cars.

On your wheel and tire choice i would go 18" or 20" as odd size wheels and tires cost a bit more, and the selection isnt all that great.

Sounds good! It is lowered by about one and a quarter inch. I'll have to test fit to assure clearance. I already have the wheels...19" mustang wheels from the later models with brembo brakes.

[Krytin]

Right front fender liner & the wire harness that runs between it and the fender may be a problem if you are lowered. I cracked the liner & wore a hole in it with the outside shoulder of the tire and gave the harness a nasty rub!
When I replaced the liner I relocated the harness to the top of the liner and cut away the molded box on the liner that used to shield the harness - just where the tire would hit/rub. Been good ever since!

[05crownsport]

Right front fender liner & the wire harness that runs between it and the fender may be a problem if you are lowered. I cracked the liner & wore a hole in it with the outside shoulder of the tire and gave the harness a nasty rub!
When I replaced the liner I relocated the harness to the top of the liner and cut away the molded box on the liner that used to shield the harness - just where the tire would hit/rub. Been good ever since!

That's good heads up information!

[Ari]

Motown Marauder: How does the car handle with those fat tires? How's the braking?

What's the consensus on a 275/40/18? Is that a correct enough tire height? I plan to lower the car perhaps an inch or an inch and a half.

[MOTOWN]

Motown Marauder: How does the car handle with those fat tires? How's the braking?

What's the consensus on a 275/40/18? Is that a correct enough tire height? I plan to lower the car perhaps an inch or an inch and a half.

Havent driven it yet, just finishing up my build, should be running by the end of the month.

is that on the front or the rear? sounds like a short tire

[Ari]

The 275/40/18 would be for the front. It's hard to find a 275/45/18. Is a 40 height too short?

[MOTOWN]

The 275/40/18 would be for the front. It's hard to find a 275/45/18. Is a 40 height too short?

Always look at the overall demensoins of your tire, the 45 in 275/45 18 is referring to the width of the tire, sounds like it will be shorter than the stock tire which wont look good on the car, especially one that isnt lowered.

[Ari]

Motown Marauder: I will be lowering the car 1 or 1.5 inches, I haven't decided yet. Should I still look for a 45?

[MOTOWN]

Motown Marauder: I will be lowering the car 1 or 1.5 inches, I haven't decided yet. Should I still look for a 45?

Im not sure on the height of the tire your interested in, go to the tire manufactuers web site and look at the overall demensions of the tire your interested in.

[05crownsport]

Tire rack is a good place to find information. Pick the tire of your choice, then go to the specs.

http://www.tirerack.com/tires/tires.jsp?tireMake=Continental&tireModel=ExtremeContact+DWS&sidewall=Blackwall&partnum=74YR9ECDWS&tab=Specs

[babbage]

Ari did you finally finish your 4v swap?? Post up some pics! For summer I like the Nitto 555 ZR Extreme tires. I run 265-50-18 on all 4 corners, so I can rotate them.

[Ari]

Ari did you finally finish your 4v swap?? Post up some pics! For summer I like the Nitto 555 ZR Extreme tires. I run 265-50-18 on all 4 corners, so I can rotate them.





I did! I'll have to post up a thread.

Also, I've been looking at an 18x9.5" wheel with an offset of 35. Do you guys think this would be ok? Would I need a spacer? The tires I'm looking to run all the way around is a 275/40/18

[newhook401]

Hey guys,
I'm looking to possibly buy a set of SVE bullitt wheels for my car tomorrow. They are 18x9 and 18x10 with +24 offset all around.
Will these fit with a +24 offset?
The guy said they're made to fit 04 mustangs

[a_d_a_m]

Hey guys,
I'm looking to possibly buy a set of SVE bullitt wheels for my car tomorrow. They are 18x9 and 18x10 with +24 offset all around.
Will these fit with a +24 offset?
The guy said they're made to fit 04 mustangs Holy necrothread
they will stick out too far

[newhook401]

Will I be able to roll the fenders to get enough clearance? Or would it be way too far out?

[Mr. Man]

If your talking about a Marauder the fenders are factory rolled.

[justbob]

If you’re talking about a Marauder, the rear quarter panels are factory rolled.

Fixed. [emoji1303]


Sent from my iPhone using Tapatalk Pro