Porting Trilogys and Eatons!!!

[RacerX]

We have a new guy in town over on TCG that is VERY good at porting. He's just as good as the "other" two guys and is less expensive. I knew by looking at his work he knew what he was doing and had a fellow Marauder owner and friend send his to him This is the thread link and I'll post his pics and comments here: http://www.thechicagogarage.com/forum/car-discussion/136700-trilogy-eaton-m112-port.html#post2852889

Trilogy eaton m112 port
This blower takes the cake. The rarity of this blower mixed with the challenge of me actually getting to port one was exciting and best of all ****en awesome. This blower will probably be the only one I will ever get to do .


Before and after picks

http://www.thechicagogarage.com/forum/attachments/car-discussion/23295d1388179129-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 127.649674.jpg

http://www.thechicagogarage.com/forum/attachments/car-discussion/23296d1388179142-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 141.549378.jpg

http://www.thechicagogarage.com/forum/attachments/car-discussion/23297d1388179154-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 153.282315.jpg

http://www.thechicagogarage.com/forum/attachments/car-discussion/23298d1388179184-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 183.899595.jpg

http://www.thechicagogarage.com/forum/attachments/car-discussion/23299d1388179192-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 191.482852.jpg

http://i20.photobucket.com/albums/b201/redline_tsi/79E0B429-9168-49E8-B9A0-4474E65AF9D4-3319-00000125B084155C_zps812dcd7c.j pg

[RacerX]

http://www.thechicagogarage.com/forum/attachments/car-discussion/23300-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 215.849899.jpg?amp;d=138817921 6

http://www.thechicagogarage.com/forum/attachments/car-discussion/23301-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 223.399328.jpg?amp;d=138817922 4

http://www.thechicagogarage.com/forum/attachments/car-discussion/23302-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 235.866710.jpg?amp;d=138817923 6

http://www.thechicagogarage.com/forum/attachments/car-discussion/23303-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 242.883161.jpg?amp;d=138817924 3

http://www.thechicagogarage.com/forum/attachments/car-discussion/23304-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 255.666030.jpg?amp;d=138817925 6
Attached Images http://www.thechicagogarage.com/forum/attachments/car-discussion/23300d1388179216-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 215.849899.jpg http://www.thechicagogarage.com/forum/attachments/car-discussion/23301d1388179224-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 223.399328.jpg http://www.thechicagogarage.com/forum/attachments/car-discussion/23302d1388179236-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 235.866710.jpg http://www.thechicagogarage.com/forum/attachments/car-discussion/23303d1388179243-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 242.883161.jpg http://www.thechicagogarage.com/forum/attachments/car-discussion/23304d1388179256-trilogy-eaton-m112-port-imageuploadedbytapatalk1388179 255.666030.jpg

[Limited360]

epic pic fail :(

I need mine ported ASAP.... tell he can do two at once! :)

[guspech750]

Yes. I saw that thread on TCG. Looks like he does very good work, super prices and I think he is only an hour & half or two from me.

WINNING!!


Sent from The White House on taxpayers dimes.

DTR + 4.10's + Eaton swap = Wreeeeeeeeeeeeeeedom

[ajdereicup]

He does really nice work and he's not trying to get rich with his prices. I had him do an M112 for me and do some different porting on an intake I later decided not to use. He doesn't just stick with blowers he'll port most things I think and do a good job. Lemme see if I can find some of my pics of my eaton.

[ajdereicup]

http://distilleryimage1.s3.amazonaws. com/d31ed04e6f8611e38fee0eec16a001 d9_8.jpg
http://distilleryimage11.s3.amazonaws .com/e50ce1246f8611e396db121ccdcfff a7_8.jpg

[RacerX]

^ Nice work! Those M112 pics were some of a bunch he showed me. Definitely in the class of Brian of Posi and Stiegemeier!

[Jokerzl]

37005


37006

37007

37008

37009

Here is some pics of his work

He don't claim to be the best but he does a really good job for a real good price

[jwibbity]

so how much is he charging and whats the turnaround time?!?

[RacerX]

so how much is he charging and whats the turnaround time?!?
That was Brett hinself that just posted above you and I'm sure he'll chime in and answer any of your questions. :beer:

[Jokerzl]

First off I shouldn't be joining without talking about a vendorship

[Jokerzl]

I did that all for 375 shipped back to your door

I did three Peices

[Jokerzl]

With advanced planning and scheduling I can this back to you with in a week. These superchargers are rare, expensive , and IMO like a peice if china I don't want to drop it or anything. So I take my time.

I also offer paint jobs as well.

[jwibbity]

that sounds like a damn good deal, ill be getting with you in the future for this....

[Jokerzl]

that sounds like a damn good deal, ill be getting with you in the future for this....

No problem

[Limited360]

I did that all for 375 shipped back to your door

I did three Peices

As soon as Jerry gets over here and pulls my blower I will have to get in touch with you for sure!!! I need my intake mated to a dragon single blade throttle body to make sure it clears!!

Work looks wonderful and glad to see that your offering the service!

:banana2::banana2:

[Jokerzl]

Can I talk to a moderator

I don't want to be banned and would like to be responsible person

I'm a one man show and would like to get on a site supporter or a monthly fee to sell here

[Jokerzl]

As soon as Jerry gets over here and pulls my blower I will have to get in touch with you for sure!!! I need my intake mated to a dragon single blade throttle body to make sure it clears!!

Work looks wonderful and glad to see that your offering the service!

:banana2::banana2:

Done that many times


37013

37014

[Limited360]

Yeah RACER X said good things about you and I have had some good tuning conversations on here with him... so have some faith in him. I am on disability so I can't wrench on my car at the moment is all...

[Jokerzl]

He is a good man

[fastblackmerc]

Can I talk to a moderator

I don't want to be banned and would like to be responsible person

I'm a one man show and would like to get on a site supporter or a monthly fee to sell here

Send a PM to ADMIN.

[Mebot]

Wow those pictures are amazing! Like night and day difference

[Vortech347]

Got any before/after dyno numbers from said porting?

[Jokerzl]

37037

This is my lightning port

I'm very good with a lightning blower.

Before and after

Same timing

No change in pullies

[jwibbity]

37037

This is my lightning port

I'm very good with a lightning blower.

Before and after

Same timing

No change in pullies

man those are some nice numbers!!!!! Now i'm itching to get this done!!

[Limited360]

37037

This is my lightning port

I'm very good with a lightning blower.

Before and after

Same timing

No change in pullies


Torque curve shape improvement is the most important thing that I see :)


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1) so I may sound retarded.

[Jokerzl]

I'm a descent porter offer a good product

It's not the best out there but does a damn good job.

[RacerX]

Dollar per horsepower, that's just plain awesome. :beer:
Cleaned up the dyno sheet btw:

http://www.mercurymarauder.net/gallery/data/675/medium/Jokerz_Port.jpg (javascript:;)

[MM03MOK]

Can I talk to a moderator

I don't want to be banned and would like to be responsible person

I'm a one man show and would like to get on a site supporter or a monthly fee to sell here

Brett
I received your email request. I will forward the vendor pricing and forum information when I get back to my desktop.

Mary

[Jokerzl]

Ok sounds good

Hopefully we can work something out

[lancejlove]

Where exactly are you located? I see you're in IL but that dynosheet says ft mill sc.





37037

This is my lightning port

I'm very good with a lightning blower.

Before and after

Same timing

No change in pullies

[Jokerzl]

Where exactly are you located? I see you're in IL but that dynosheet says ft mill sc.

Illinois

My biggest client base is In the southeast

Not to many people in Chicago modify vehicles

[lancejlove]

Okay well I want to get this done also. Whenever I figure out how to get my blower off I will be sending it to you.




Illinois

My biggest client base is In the southeast

Not to many people in Chicago modify vehicles

[Jokerzl]

Wow sounds great

Sledgehammer works well

[RacerX]

Okay well I want to get this done also. Whenever I figure out how to get my blower off I will be sending it to you.
The Trilogy Motorsports Marauder Instal/removal manual is on this page at the lower right. (Marauder Supercharger Manual)
http://www.trilogymotorsports.com/products/

[lancejlove]

Lol okay I may try that method...lol remember you said use a sledgehammer



Wow sounds great

Sledgehammer works well


Thanks a lot I'm gonna take a look at that and see if it's something I'm comfortable doing


The Trilogy Motorsports Marauder Instal/removal manual is on this page at the lower right. (Marauder Supercharger Manual)
http://www.trilogymotorsports.com/products/

[nh muscle]

Its like circumsising a baby!!

[Jokerzl]

I used a 14 inch diamond saw

37057

[guspech750]

I used a 14 inch diamond saw

37057

:lol:
:lol:


Sent from The White House on taxpayers dimes.

DTR + 4.10's + Eaton swap = Wreeeeeeeeeeeeeeedom

[Jokerzl]

There is a video

[RacerX]

:D Once you get the sc assembly out of the engine bay, have a box of razor blades and a couple of thin putty knives at the ready. Not the cheap Chinese box of razor blades where they come apart either! Ask Ken! This is to split the RTV seal between the SC and lower plenum. Unless Brett had a quicker way of separating... Without a diamond saw! :lol:

[Blackened300a]

Okay well I want to get this done also. Whenever I figure out how to get my blower off I will be sending it to you.

Its a pain in the ass. I was going to pull mine apart to swap out the coupler, but I didn't feel like getting involved with it after looking at all the crap I have to do to yank it off. Also be careful when separating the blower plate. If you pry too much you can put a wave in it which will result in a vacuum leak and you'll be pulling it off again trying to seal it.

[nh muscle]

those razor blades were 15 years old!!! they held up well!

[Jokerzl]

:D Once you get the sc assembly out of the engine bay, have a box of razor blades and a couple of thin putty knives at the ready. Not the cheap Chinese box of razor blades where they come apart either! Ask Ken! This is to split the RTV seal between the SC and lower plenum. Unless Brett had a quicker way of separating... Without a diamond saw! :lol:


If you take your time with a heat gun some brake fluid and work your way around the brake fluid softens up the silicone heat it up cool it down heat it up cool it down. The expansion of the metal helps breaks up the silicone meaning separate it slowly the brake fluid then penetrates it and gets trapped and slowly eats at it. It's a slow process but I feel it's the safest and easiest way because it dries the silicone out.

I may have not said that right but you get my point

Green can not the red can.

[Jokerzl]

Also racer

37065

37066

37067

37068

37069

37070

37071

[Jokerzl]

37072

Last picture

[guspech750]

God I need to pull my Eaton off soon and ship it to you.


Sent from The White House on taxpayers dimes.

DTR + 4.10's + Eaton swap = Wreeeeeeeeeeeeeeedom

[Jokerzl]

I did that and a lightning today

37073
37074
37075

[ajdereicup]

Might I ask what the front hole cutout is for? For TQ HP a mix or...? Just curious I remember you telling me how you shape it can effect where the power is at or something along those lines

[Jokerzl]

Might I ask what the front hole cutout is for? For TQ HP a mix or...? Just curious I remember you telling me how you shape it can effect where the power is at or something along those lines


Aj since I ported yours I have been on the flow bench and dyno. This is the design that I came up with that was mine and not copying someone else's.

My standard port was good for 24 hp and 16 ft lbs

My race port was good for 41 and 22 ft lbs

37076


37077


37078

37079

The designs resulted in less case pressure the movement of air speed picked up. Which I thought would relate to less tq. But my new design gained in torque which was awesome and just a bonus .the more air you can cram in there before the exit the better but have to come up with a way to keep a balance.

[ajdereicup]

Hmmmm very interesting stuff. You have don't happen to have a plasma cutter and aluminum tig welder do you? I ventured away from the 351W efi intake in the plan and have another one. A LOT more simple except I don't have the tools. That is if you'd be interested

[Jokerzl]

I do know of someone who can set you up

[ajdereicup]

Alright cool. I gotta get some measurements as far as angle and lining up the pulley when I pull the carb off to do some work to it when it warms up so once I get them I'll ask you again man. I appreciate it.

[Jokerzl]

37086

37087



37088

37089

37090

[Jokerzl]

Shooting for 500 hp stock block

[Limited360]

Shooting for 500 hp stock block


This is what I like to think


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1) so I may sound retarded.

[Jokerzl]

This is what I like to think


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1) so I may sound retarded.


Stock block lightning 8 lb lower full port work turkey pan to throttle body gasket matched longtubes headers 60 injectors

Meth injection shoot for 18 degrees of timing with 93 and 20 with c16 and meth

Should put between 480-500 hp 550-575 tq

Hoping it's just a goal

[Limited360]

Stock block lightning 8 lb lower full port work turkey pan to throttle body gasket matched longtubes headers 60 injectors

Meth injection shoot for 18 degrees of timing with 93 and 20 with c16 and meth

Should put between 480-500 hp 550-575 tq

Hoping it's just a goal


That's what I would like to get up around until I grenade my engine and have to do something with the 4.6l aluminum mark VIII motor sitting around.


Sent from my iPhone using Tapatalk (http://tapatalk.com/m?id=1) so I may sound retarded.

[Jokerzl]

You guys with marauders be interested in this?

37091

37092

[Jokerzl]

37099

37100

[RacerX]

You guys with marauders be interested in this?

http://www.mercurymarauder.net/forums/attachment.php?attachmentid=37 091&d=1388946808

Wait a minute!!! You know someone making those adapter plates? How much???

[guspech750]

You guys with marauders be interested in this?

37091

37092

Yeah, I bet there would be quite a few possibly Eaton swap people that would be interested in this, as long as it clears the wiper cowl. This would cut down on a considerable amount of time with very minimal cutting of the harnesses.


Sent from The White House on taxpayers dimes.

DTR + 4.10's + Eaton swap = Wreeeeeeeeeeeeeeedom

[Jokerzl]

You guys with marauders be interested in this?

http://www.mercurymarauder.net/forums/attachment.php?attachmentid=37 091&d=1388946808

Wait a minute!!! You know someone making those adapter plates? How much???


Yep I know someone

I need a donator car and would get a free adaptor plate

Plates for lightnings are 575 shipped

[Jokerzl]

That will bolt up a gt500 whipple 2.9 or TVS blower

[massacre]

That will bolt up a gt500 whipple 2.9 or TVS blower

Is this for lighting only?

[guspech750]

I recall someone making an adapter plate for the 4.6 Cobra motors to use the M122.




Sent from The White House on taxpayers dimes.

DTR + 4.10's + Eaton swap = Wreeeeeeeeeeeeeeedom

[RacerX]

Yeah, Cobra Engineering. If I remember right, it was a lot more $$$.

[Jokerzl]

Is this for lighting only?


He wants to expand

Latest dyno on m122 stock block lightning

37101

[Mebot]

Subscribing to this thread. When I get my Trilogy I will be sending it to you for work.

[Jokerzl]

Starting an m122 port job

37126

37127

37128

[Jokerzl]

37133


37134

37135

37136

37137

37138

37139

37140

37141

37142

37143

[Jokerzl]

37144

37145

37146

37147

[Ninoblack1]

37144

37145

37146

37147

wow what a job a++:banana2: