View Full Version : 2 Valve = simple swap?
Motorhead350
05-19-2014, 01:38 PM
Yes or no?
If no what is required.
Looks like a blew another engine by starting it.
RF Overlord
05-19-2014, 01:40 PM
What?!
I don't think your computer will run a 2V, so you'll need the PCM and the engine wiring harness at least.
fastblackmerc
05-19-2014, 02:19 PM
Don't know how you can blow an engine by starting it... but then again this is Dom.....
I suggest a years supply of bus passes.
http://www.transitchicago.com/travel_information/fares/unlimitedridecards.aspx
Will be cheaper for you in the long run.
ChiTownMaraud3r
05-19-2014, 02:25 PM
Wasn't your girl using it perfectly fine while you were gone Dom? What happened now?
Sammich
05-19-2014, 02:58 PM
http://www.crownvic.net/ubbthreads/ubbthreads.php?ubb=showflat&Number=2341795
http://www.modularfords.com/threads/91637-My-2v-to-4v-swap-write-up
Lots (relatively) of info on going 2v to 4v; it seems pretty straightforward. I can't imagine going the other way would be much harder, but I'm no expert.
Why not just put in another 4v?
Motorhead350
05-19-2014, 03:12 PM
I didn't post up to be insulted, but then again I am Dom and it's not only acceptable it's encouraged here.
Why did I even post? Useless as a condom at a lesbo swinger party.
Spectragod
05-19-2014, 05:38 PM
You could use your computer, but it would require a lot of reprogramming, and a wiring harness, I think it would be easier and cheaper to find a 4v...
marauderthis
05-19-2014, 06:36 PM
If I recall a while back when it was nice and cold you had over heating issues - which probably sealed your engines fate. Don't you just love that COT design.
I feel for you If you do replace your motor get ready for for more Ford fun... your EATC or the blend door servo motor will go to crap ... Again
J-MAN
05-19-2014, 07:28 PM
Tough break. Might be time to unload it and get a mini van, those are 2 valve.
lji372
05-19-2014, 07:37 PM
Store it. Get a 4 banger, put the money from gas savings away until you save enough for a rebuilt long lock with a warranty just my .02
http://img.tapatalk.com/d/14/05/20/agu8ygu2.jpg
MyBlackBeasts
05-19-2014, 07:49 PM
What actually happened Dom?
Motorhead350
05-19-2014, 07:52 PM
Drove it last night without going to Mexico. Decided to check on the plugs for proper gap this morning. Put them back in and hear the rattle of money.
MyBlackBeasts
05-19-2014, 07:59 PM
Drove it last night without going to Mexico. Decided to check on the plugs for proper gap this morning. Put them back in and hear the rattle of money.
Pull plugs again & inspect.
Look for damaged/missing electrode or inner ceramic insulator.
Who knows, you might get lucky... Fingers crossed!
Motorhead350
05-19-2014, 08:03 PM
I pulled them 3 times.
The only thing left to do is pull them a 4th time and run my extendo magnet down the heads. Even if it takes 4 minutes I bet it's 4 minutes wasted.
Chi Stallion
05-19-2014, 08:26 PM
Store it. Get a 4 banger, put the money from gas savings away until you save enough for a rebuilt long lock with a warranty just my .02
http://img.tapatalk.com/d/14/05/20/agu8ygu2.jpg
My boy Johnny 5 to the rescue!!!!
Sent from my iPhone 5 using Tapatalk
MyBlackBeasts
05-19-2014, 08:32 PM
I pulled them 3 times.
The only thing left to do is pull them a 4th time and run my extendo magnet down the heads. Even if it takes 4 minutes I bet it's 4 minutes wasted.
Magnet won't help.
Stick a snake inspection camera down the hole & inspect.
They are real cheap now. I got one from Oriely for $80.
Don't run it any more till you find what it is!
Motorhead350
05-19-2014, 08:38 PM
I hope they rent them out.
ajdereicup
05-19-2014, 11:28 PM
I've got an inspection camera but don't know if its small enough to fit in the spark plug hole?
lji372
05-20-2014, 06:24 AM
buy it use it take it back, just sayin. sometimes you gotta do what you gotta do :D
http://www.harborfreight.com/catalogsearch/result/?q=borescope
RacerX
05-20-2014, 07:51 AM
Synopsis: Ran fine. No unusual noises. Changed plugs, now have an engine rattle.
Does this noise appear in any particular location? Particular cylinder, side, upper or lower? Does it get louder if you lightly open the throttle?
Vortech347
05-20-2014, 07:51 AM
I didn't post up to be insulted, but then again I am Dom and it's not only acceptable it's encouraged here.
Why did I even post? Useless as a condom at a lesbo swinger party.
And yet you still do... :D
Swapping in a 2v would cost more in killing the value and in parts/labor than fixing the 4v in it.
massacre
05-20-2014, 09:51 AM
Dom you are not mechanically or financially inclined enough for a 2v swap. Nothing personal, just being honest.
fastblackmerc
05-20-2014, 10:16 AM
Dom you are not mechanically or financially inclined enough for a 2v swap. Nothing personal, just being honest.
+1... that's why I suggested the bus...............
Motorhead350
05-20-2014, 10:50 AM
2 Valve was to save money. I do not give a hoot about value. I need to get around. 1320 days are behind me.
I have a video, but do not know how to post it.
I have not really played with the throttle. It still runs.
Vortech347
05-20-2014, 11:05 AM
You will spend more in labor costs and tuning to make it work. You would need to swap the entire harness and ECU if you want it to run worth a damn.
Just fix the 4V that's in it. Its not rocket science.
Motorhead350
05-20-2014, 11:07 AM
You will spend more in labor costs and tuning to make it work. You would need to swap the entire harness and ECU if you want it to run worth a damn.
Just fix the 4V that's in it. Its not rocket science.
That's the answer.
Thank you.
:depress:
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions Inc. All rights reserved.