Log in

View Full Version : Wanted To Buy steeda crank pully install bolt



crownvic05
06-16-2014, 05:40 PM
Any one want to lend me theres or sell it to me?

tbone
06-16-2014, 08:42 PM
Have you tried to install it with the regular bolt? I didn't need one. It slid on far enough to catch.

crownvic05
06-16-2014, 08:44 PM
No havent tried yet. I just want to be prepaired just in case. Also, did your crank pully just slide right off(talking about stock one)?

tbone
06-16-2014, 08:54 PM
You need a pulley puller. I got a kit at Harbor Freight for like $16.

crownvic05
06-17-2014, 04:31 AM
You need a pulley puller. I got a kit at Harbor Freight for like $16.

mind showing me which one you got?

Thanks

fastblackmerc
06-17-2014, 05:01 AM
mind showing me which one you got?

Thanks

You can borrow one from most FLAPS.

This should be the one from Harbor Freight:

http://www.harborfreight.com/bolt-type-wheel-puller-set-69889.html

tbone
06-17-2014, 06:12 AM
That's the one.

For the cost of a hammer, might as well just buy it.

fastblackmerc
06-17-2014, 06:58 AM
That's the one.

For the cost of a hammer, might as well just buy it.

I agree, you can also use it for pulling steering wheels.

whitey
06-17-2014, 07:29 AM
Ive got an install bolt. You pay shipping and return it when your done with it and its yours to use. Pm me.

whitey
06-17-2014, 07:34 AM
Also, allensfasteners.com has the arp crank bolts cheapesthttp://img.tapatalk.com/d/14/06/17/y5y6aren.jpg part # 156-2501

fastblackmerc
06-17-2014, 09:06 AM
mind showing me which one you got?

Thanks

Be sure to apply a dab of silicone sealer to the key way in the damper. It will seep oil if you don't.

crownvic05
06-17-2014, 10:03 AM
Be sure to apply a dab of silicone sealer to the key way in the damper. It will seep oil if you don't.

Great thanks.

fastblackmerc
06-17-2014, 10:16 AM
Installation instructions from the Steeda website

http://www.americanmuscle.com/steeda-underdrive-pulley-install.html

Disregard the alternator pulley section.

If you don't have an impact gun to remove the balancer bolt you'll need two people. One the turn the bolt and one to stop the engine from turning. Remove the inspection plate from the transmission bell housing and wedge a crowbar between the teeth and the bell housing.

NOTE: not responsible for any damage that may occur.

BAD MERC
06-17-2014, 10:49 AM
What kind of car is it going on? (here, you have to ask!!) I had the Steeda UDP on my car and from experience, you'll probably want to have a tuner and raise the idle 200 - 300RPM because you charging system will suffer, as will the A/C and power steering.

fastblackmerc
06-17-2014, 10:52 AM
What kind of car is it going on? (here, you have to ask!!) I had the Steeda UDP on my car and from experience, you'll probably want to have a tuner and raise the idle 200 - 300RPM because you charging system will suffer, as will the A/C and power steering.

It only will suffer with all the electrical stuff on at the same time at idle.

crownvic05
06-17-2014, 11:44 AM
05 crown vic sport. Alternator pully will not be used.

DarthLord
06-17-2014, 11:46 AM
Keep us posted on the install!