PDA

View Full Version : Sean Hyland stage 1cams


Finally
08-07-2014, 12:39 PM
Sean hyland stage 1 billet 4 valve cams
Low mile billet stage one cams for modular 4 valve
Shm part 2710
209* @ .050 intake and exhaust
0.452 lift intake and exhaust

How would these cams work for a NA application in our Mauraders.
Thanks
sailsmen
08-07-2014, 04:06 PM
I wouldn't give him a penny for a paper weight.
Jeronimojc
08-07-2014, 04:26 PM
What are you trying to accomplish? Have you considered Cobra 98 cams?


Sent from my iPhone using Tapatalk
Finally
08-07-2014, 05:12 PM
What are you trying to accomplish? Have you considered Cobra 98 cams?


Sent from my iPhone using Tapatalk

I found a set and the price is right,just looking for a little more pep and a performance idle,I'm already waiting to imstall my 3:90 gears,3000 stall converter and stainless works long tubes,the cams would be the final touch.
Finally
08-08-2014, 09:31 PM
No one here has run these cams ??
Jeronimojc
08-08-2014, 09:57 PM
I can't give you any advice, but I recently researched cams. I understand most cams that work well on other vehicles, may kill the power where a Marauder needs it. The post an thread below may be of some help.


Specs for cams that would work great with stock springs would look something like this: 220/218, .425" lift, 109LSA with a 3 degree advance

The cams in the video are 226/222, .425", 110LSA with a 4 degree advance.

http://www.mercurymarauder.net/forums/showthread.php?t=74902



Sent from my iPhone using Tapatalk
ctrlraven
08-08-2014, 10:04 PM
No one here has run these cams ??
Do a search around a couple of Mustang sites you will find their reputation to not be favorable.

Most go with 96-98 Cobra intake (only) cams and have them degreed.
Finally
08-08-2014, 10:31 PM
Do a search around a couple of Mustang sites you will find their reputation to not be favorable.

Most go with 96-98 Cobra intake (only) cams and have them degreed.

Thanks that is what I was doing,maybe I'll just stick with going with a Bullet custom grind or the GT 500 cams,being an old hotrodder I want a little rumpity rump in the idle.
Where would one look for the GT500 cam kit.
WPG_Merc
08-09-2014, 12:28 AM
My Comp Stage 3 Blower Cams - "Intake 475 Lift & Exhaust 450 Lift" work great on the car.
:burnout:
Mike M
08-09-2014, 12:39 AM
My Comp Stage 3 Blower Cams - "Intake 475 Lift & Exhaust 450 Lift" work great on the car.
:burnout:

Best sounding Marauder out there. I want these cams.
J-MAN
08-09-2014, 03:32 AM
Aren't Sean Hyland cams regrinds that require shimming?
massacre
08-09-2014, 05:57 AM
Just FYI on Modulars the lopey idle sounds great but doesn't make the most power.
And on the '96-'98 Cobra intake cams to get the most power they must be advanced, not just degreed.
fastblackmerc
08-09-2014, 08:31 AM
I found a set and the price is right,just looking for a little more pep and a performance idle,I'm already waiting to imstall my 3:90 gears,3000 stall converter and stainless works long tubes,the cams would be the final touch.

You'd be better off installing 4.10's.
Jeronimojc
08-09-2014, 08:44 AM
^ +1


Sent from my iPhone using Tapatalk
Finally
08-09-2014, 09:20 AM
You'd be better off installing 4.10's.

I want that couple less hundred rpm on the hwy which is why I am going 3:90 gears,
Finally
08-09-2014, 09:24 AM
Just FYI on Modulars the lopey idle sounds great but doesn't make the most power.
And on the '96-'98 Cobra intake cams to get the most power they must be advanced, not just degreed.

I do know that but it's like hearing a good song on the radio,I think if I go custom grind I can have my cake and eat it too.from my reading the gt500 cams are a great NA cam also.
Jeronimojc
08-09-2014, 09:47 AM
I do know that but it's like hearing a good song on the radio,I think if I go custom grind I can have my cake and eat it too.from my reading the gt500 cams are a great NA cam also.


Great for a MM or for a mustang? Not to give you a hard time. Just curious. Where did you read that? Can you post the specs?


Sent from my iPhone using Tapatalk
Finally
08-09-2014, 10:16 AM
Every thing out there is for Mustangs,I'm just doing some late nite reading on what out there and what some like.not an expert by any means,I just know by now what I want if I pay out the bucks to get a cam swap done..
Chayton
08-09-2014, 01:43 PM
Every thing out there is for Mustangs,I'm just doing some late nite reading on what out there and what some like.not an expert by any means,I just know by now what I want if I pay out the bucks to get a cam swap done..

whats the going price on a cam swap anyways? especially when you have 4...
Jeronimojc
08-09-2014, 06:37 PM
Every thing out there is for Mustangs,I'm just doing some late nite reading on what out there and what some like.not an expert by any means,I just know by now what I want if I pay out the bucks to get a cam swap done..


A few Marauder and several Mach1 guys have used Cobra 98 cams. Advancing them is key to making them work well on MMs. That's what I bought ($160) and will install on my MM.


Sent from my iPhone using Tapatalk
Finally
08-09-2014, 09:20 PM
whats the going price on a cam swap anyways? especially when you have 4...

Haven't got that far yet,but a wild guess I am expecting a thousand to fifteen hundred bucks.
But just a guess
cat in the hat
08-10-2014, 09:56 AM
My Comp Stage 3 Blower Cams - "Intake 475 Lift & Exhaust 450 Lift" work great on the car.
:burnout:


Best sounding Marauder out there. I want these cams.

+2, do want :)
Finally
08-10-2014, 08:51 PM
I can't give you any advice, but I recently researched cams. I understand most cams that work well on other vehicles, may kill the power where a Marauder needs it. The post an thread below may be of some help.



http://www.mercurymarauder.net/forums/showthread.php?t=74902



Sent from my iPhone using Tapatalk

Thank you very helpfull info,I think custom is the way to go.
Cheers
Tony