Stainless Works catted exhaust.

[Comin' in Hot]

For sale is my Stainless Works catted exhaust.

Part Number: MAUEX-CAT
Retail Price is $1330.00, you could find it elsewhere for a little bit of a discount but you'll never find it at my price.

My price: $950.00

Mileage: less than 200 miles ( not a typo). Most of the decals aren't even burned off.


I bought a full stainless works exhaust without ever thinking it wouldn't work on my car.

Why it won't fit my marauder but it will fit yours:

1. My marauder has a 4 inch aluminum driveshaft, factory is 3" most after market driveshafts are 3.5".

2. The larger driveshaft caused me to modify my DS loop to a larger diameter.

3. The stainless works x-pipe needed to be mounted lower than probably any other marauder out there to clear the driveshaft and DS loop.

4. The lower X-pipe caused a butterfly effect to the over the axle pipes being about 2" lower than normal. Normally this would not have been an issue but my car sits a good 3"+ at the rear lower than a stock marauder. The compounding problems caused my Metco watts link to slightly rub up against the over the axle pipes when I drive over bumps. The stainless over axle pipes are fine with no dents, but they have a few slight scratches on them from wearing down my aluminum watts link.

All that being said, the 200 miles was because I had no other way to get it to the customer exhaust shop.

Issues: anyone that has ever worked with stainless, knows it's basically glues itself together. I needed to heat two areas to get the pipes separated so there is some discoloration. I also accidentally dented a muffler when a the wood buffer I used slip and I tapped the muffler with a hammer, but heated it and straightened it out(see pics), i'm sure it's fine.

This kit would be ideal for the guy wanting the kit but different mufflers.

http://i22.photobucket.com/albums/b335/Witman40/8D67124F-7D50-4C27-9E14-7F64A3679787_zps3oprzszc.jpg (http://s22.photobucket.com/user/Witman40/media/8D67124F-7D50-4C27-9E14-7F64A3679787_zps3oprzszc.jpg.h tml)

http://i22.photobucket.com/albums/b335/Witman40/B3D8823A-BB98-4D43-81D4-86911DE2D1E4_zpspklmpzh5.jpg (http://s22.photobucket.com/user/Witman40/media/B3D8823A-BB98-4D43-81D4-86911DE2D1E4_zpspklmpzh5.jpg.h tml)

http://i22.photobucket.com/albums/b335/Witman40/708A26CB-4E44-40C3-8A1C-DD86FE388B51_zpsmuo50b63.jpg (http://s22.photobucket.com/user/Witman40/media/708A26CB-4E44-40C3-8A1C-DD86FE388B51_zpsmuo50b63.jpg.h tml)

http://i22.photobucket.com/albums/b335/Witman40/91F1A1BB-5EB4-4BE8-8791-4158CA58511F_zpsosrbqdzz.jpg (http://s22.photobucket.com/user/Witman40/media/91F1A1BB-5EB4-4BE8-8791-4158CA58511F_zpsosrbqdzz.jpg.h tml)

http://i22.photobucket.com/albums/b335/Witman40/7A4DCEBB-F371-4CD3-B850-4EE6433D955E_zpsmnqycgrl.jpg (http://s22.photobucket.com/user/Witman40/media/7A4DCEBB-F371-4CD3-B850-4EE6433D955E_zpsmnqycgrl.jpg.h tml)

http://i22.photobucket.com/albums/b335/Witman40/F355EBA4-E48C-42EA-84A3-C74CAA456E79_zps7h6jbwbg.jpg (http://s22.photobucket.com/user/Witman40/media/F355EBA4-E48C-42EA-84A3-C74CAA456E79_zps7h6jbwbg.jpg.h tml)

http://i22.photobucket.com/albums/b335/Witman40/ADC04AB5-A4E6-443C-B815-924870C190D5_zpsfuprd50c.jpg (http://s22.photobucket.com/user/Witman40/media/ADC04AB5-A4E6-443C-B815-924870C190D5_zpsfuprd50c.jpg.h tml)

[Logizyme]

So this only fits with stainless works headers correct or a custom downpipe?

[Comin' in Hot]

So this only fits with stainless works headers correct or a custom downpipe?

You are correct. If you're interested I'll throw in a set of FRP Cobra Shorty headers that need to be repaired and custom down pipes. The downpipe's have bungs for the front O2 sensors as well as wideband sensor.

All you need to do is have an exhaust shop connected them.

http://i22.photobucket.com/albums/b335/Witman40/3B086302-E0B0-41FE-B4B1-944FF5F4CF10_zpsyk3lpkr0.jpg (http://s22.photobucket.com/user/Witman40/media/3B086302-E0B0-41FE-B4B1-944FF5F4CF10_zpsyk3lpkr0.jpg.h tml)

[kariamack]

2.5 inch or 3 inch ??

[Logizyme]

3 inch to the mufflers(leads, cats, xpipe midpipe), 2.5 after the mufflers(over axle to tips)

Which is the only way Stainless Works makes the "Marauder" exhaust, the 2v Vic/Marquis Stainless works kit is all 2.5 cat back - which could in theory be used on a Marauder.

[Comin' in Hot]

Price drop

[License2Bill]

Sending PM

[Guittard22]

Sending PM



Dam bill spending sone money lol

[eennte]

That system won't work without headers?

[Comin' in Hot]

That system won't work without headers?


It will work, but you will need to have an exhaust shop make lead pipes from your manifolds to the cats.

[Chi Stallion]

Wait so I still haven't had my SW headers and SW full catted exhaust system put in yet.. Is there anything i should worry about if I have the 4in Dynotech driveshaft? I already have the Metco watts link installed. Ride height sensor is new too and j believe it's about the same as stock maybe an inch or 2 higher.


Sent from my iPhone 5 using Tapatalk

[Comin' in Hot]

Sold.... Please close the thread

[Guittard22]

Sweet bill

[License2Bill]

Received yesterday! Thanks man!

[Comin' in Hot]

Received yesterday! Thanks man!

Thanks again for taking it off my hands