Page 1 of 2 12 LastLast
Results 1 to 15 of 26

Thread: 8 bolt flexplate

  1. #1
    Join Date
    May 2007
    Location
    Massapequa Park
    Posts
    585

    8 bolt flexplate

    Looking for an eight bolt flexplate ford#m6375h46 or performance automatic sfi flexplate 8bolt pa26478-8 or an equivalent flexplate the could be used to put a cobra motor or aluminator into a marauder.

  2. #2
    Join Date
    Sep 2007
    Location
    townsend DE
    Age
    34
    Posts
    12,474
    Quote Originally Posted by tjl006 View Post
    Looking for an eight bolt flexplate ford#m6375h46 or performance automatic sfi flexplate 8bolt pa26478-8 or an equivalent flexplate the could be used to put a cobra motor or aluminator into a marauder.
    go to napa ask for a flex plate from a 99 f250 with the 5.4, should yield you the correct part. what ya got going on up there man?
    2010 fusion se


  3. #3
    Join Date
    May 2007
    Location
    Massapequa Park
    Posts
    585
    Got problems, grit left in my intake from the powdercoater has left me with a 500 pound paper weight.

  4. #4
    Join Date
    Sep 2007
    Location
    townsend DE
    Age
    34
    Posts
    12,474
    Quote Originally Posted by tjl006 View Post
    Got problems, grit left in my intake from the powdercoater has left me with a 500 pound paper weight.
    dude you gotta be ****ing kidding me! that blows man. real big. did it destroy your fresh heads too?
    2010 fusion se


  5. #5
    Join Date
    Nov 2007
    Location
    NorCal
    Age
    50
    Posts
    3,209
    Lonnie over Blue Oval Chips is where I picked up mine (FRPP M-6375-H46). At that time he was one of the only vendors to carry it....I search everywhere.
    2003 Mercury Marauder 300A
    FRPP BOSS50 Block w/MMR 900S Stroker 5.3L DOHC 324ci 10:1cr - (321rwhp/360.5rwtq) - Tuned by AED

    2006 Ford Mustang GT
    FRPP FR3 Handling Pack|FRPP X Pipe w/GTA Exhaust|Steeda CAI|Hurst Shifter
    (289rwhp/307rwtq)

    2003 Chevrolet Suburban 2500 LQ4 6.0L LT 4WD
    Cognito leveling Kit, Fox 2.0, BFG KOA2 Radial All Terrains, Magnaflow, K&N and 4.10 gears

  6. #6
    Join Date
    May 2007
    Location
    Massapequa Park
    Posts
    585
    When the motor comes back out I got to check the valves but i assume the guides and stems are scored. Apparently beating the intake into the sidewalk multiple times, running a leafblower through it and using a garden hose wasnt enough to remove the baked in grit. The intake inlets felt like the beach.

  7. #7
    Join Date
    Sep 2007
    Location
    townsend DE
    Age
    34
    Posts
    12,474
    thats insane. got a line on a short block?
    2010 fusion se


  8. #8
    Join Date
    Apr 2009
    Location
    michigan
    Posts
    1,392
    Man that suck I know you've been trying hard to get your engine together and now this.
    My garage
    http://www.mercurymarauder.net/forum...=view&id=10419

    04/30/11
    1/8 mile 7.7430 at 89.24
    1/4 mile 12.16 at 110.66(calculated)

  9. #9
    Join Date
    Sep 2007
    Location
    townsend DE
    Age
    34
    Posts
    12,474
    hey Tom, this may be on interest.

    http://www.svtperformance.com/forums...ad-piston.html
    2010 fusion se


  10. #10
    Join Date
    May 2006
    Location
    Maryland
    Posts
    671
    Quote Originally Posted by ImpalaSlayer View Post

    or this one I've been watching it for awhile


    http://www.svtperformance.com/forums...lots-mods.html

  11. #11
    Join Date
    Jul 2004
    Location
    The Dirty South
    Age
    52
    Posts
    3,836
    Man I know what a hard time you've had with the MM since the Eaton. If you need some help PM me, it would be my pleasure.

  12. #12
    Join Date
    Nov 2007
    Location
    NorCal
    Age
    50
    Posts
    3,209
    Man good luck with all that man. Sometimes I wonder about this hobby...Ive dump so much $$$ into mine it aint even funny.

    My 2 cents go with an aluminator LB I was quoted $5200 shipped for an NA Aluminator LB.
    2003 Mercury Marauder 300A
    FRPP BOSS50 Block w/MMR 900S Stroker 5.3L DOHC 324ci 10:1cr - (321rwhp/360.5rwtq) - Tuned by AED

    2006 Ford Mustang GT
    FRPP FR3 Handling Pack|FRPP X Pipe w/GTA Exhaust|Steeda CAI|Hurst Shifter
    (289rwhp/307rwtq)

    2003 Chevrolet Suburban 2500 LQ4 6.0L LT 4WD
    Cognito leveling Kit, Fox 2.0, BFG KOA2 Radial All Terrains, Magnaflow, K&N and 4.10 gears

  13. #13
    Join Date
    Sep 2007
    Location
    townsend DE
    Age
    34
    Posts
    12,474
    Quote Originally Posted by Speed View Post
    or this one I've been watching it for awhile


    http://www.svtperformance.com/forums...lots-mods.html
    thats not bad!
    2010 fusion se


  14. #14
    Join Date
    May 2007
    Location
    Massapequa Park
    Posts
    585
    Thanks for the words guys. Right now i am strongly considering the NA aluminator got a quote from tousley $6100 shipped to the door with a twelve month warranty, asked them about the 5200 quote dohc they said it must of been a mistake, Mike and steve at tousley are good guys to deal with though. Not really looking to go with a shortblock or to deal with machine shops the more i deal with shops the sicker I get, wether it be machine shops,powdercoaters or tuners. Do it yourself with oem parts that seems for the most part(of course there are exceptions) the best way to go.

  15. #15
    Join Date
    Jul 2004
    Location
    The Dirty South
    Age
    52
    Posts
    3,836
    Can't go wrong with Tousley, those guys are great, did you ask for the discount for SVTP members?

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. flexplate 8 bolt for 32 valve 4.6l needed
    By 03slickvic in forum Marauder Parts/Misc. Wanted
    Replies: 3
    Last Post: 01-18-2008, 07:53 PM
  2. WTB: flexplate
    By Serge in forum Other Parts/Misc. Wanted
    Replies: 1
    Last Post: 07-25-2007, 06:28 PM
  3. Flexplate Shield
    By FordNut in forum Shop Talk
    Replies: 6
    Last Post: 05-29-2006, 06:20 PM
  4. Need some specs on TC and flexplate
    By Sprout in forum Shop Talk
    Replies: 4
    Last Post: 02-16-2006, 08:26 PM
  5. 4.6L Bolt-Ons
    By ap2003 in forum Shop Talk
    Replies: 7
    Last Post: 07-13-2003, 11:03 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •