Page 1 of 3 123 LastLast
Results 1 to 15 of 33

Thread: 2003-2004 Marauder bulb sizes

  1. #1
    Join Date
    Jan 2004
    Location
    Somewhere in the N.C. Triangle
    Age
    68
    Posts
    26,250

    2003-2004 Marauder bulb sizes

    Interior and Exterior bulb sizes

    Headlight – 9007 (2)
    Fog Light – H1 (2)
    Rear Stop Light / Turn Signal – 3157 (4)
    High Mounted Stop Light – 912 (2)
    Front Map Light – 168 (194) (2)
    Rear Light (long overhead console) - 42mm Festoon (1)
    Glove Compartment – 168 (194) (1)
    License Plate – 168 (194)
    Trunk Light – 2122 Festoon
    Underhood Light – 906 (2)
    Parking Light - 3157NA (amber) (2)
    Vanity Mirror – 29, 30 or 31mm 6641 (4)
    Rear Reading Light – 45mm Festoon (2)
    Front Foot Well – 168 (194) (2)
    Reverse - 3156 (2)


    NOTE: You can substitute a 194 bulb for a 912, 168 or 906 bulb.
    Last edited by fastblackmerc; 02-02-2024 at 07:38 AM. Reason: Updated all.
    “When you can’t make them see the light, make them feel the heat.”
    Ronald Regan

    "The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
    is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."

    Lt. Colonel Ralph Peters

    “Be polite, be professional, but have a plan to kill everybody you meet.”
    "I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
    General James Mattis




  2. #2
    Join Date
    Sep 2002
    Location
    Cape Cod, MA
    Posts
    13,676
    Adding Cornering lamp - 3156 (qty 2)
    The Blackbird
    Trilogy #61
    Driveway Queen

    The Spruce Goose
    2004 Grand Marquis LS Limited Edition
    Daily Driver

  3. #3
    Join Date
    Dec 2002
    Location
    north nj (Planet Houston)
    Posts
    771
    volt gauge - 168
    oil gauge - 168

    Not that it matters but since some may want that pedantic stock feeling , :
    my map lights were 906s
    dome light was - 578 (which is the same as the 212-2 festoons)
    rear readings - 211-2 (but my trunk was a 212-2)
    Last edited by the fat bastid; 09-18-2020 at 09:48 PM.
    "Come to me, Superman! I defy you! Come and kneel before Zod! Zod! "

  4. #4
    Join Date
    Nov 2006
    Location
    Ogden Utah
    Age
    42
    Posts
    2,181
    Don't forget...
    Dash Gauge cluster - Six 194 bulbs
    Shifter - One 194 bulb
    2003 300A
    Build date 9/27/02
    Sequence# 5244 of 7839
    I have a few things done to it, Eaton swap next!
    1993 Ford Taurus SHO-Every bolt on available...Awaiting a Turbo
    2008 Ford F350 SD
    1974 Ford F350 SCS
    2011 Ford Flex Titanium, Ecoboost
    www.cardomain.com/id/shofast
    If you don't stand behind our troops; please feel free to stand in front of them!

  5. #5
    Join Date
    Dec 2002
    Location
    north nj (Planet Houston)
    Posts
    771
    for the dash, i made this:


    so not only 6 illumination but if you are crazy, 10 more for the signals.
    the little blue ones ctrlraven thinks are t5s.
    I haven't pulled it apart yet.
    Attached Images Attached Images
    "Come to me, Superman! I defy you! Come and kneel before Zod! Zod! "

  6. #6
    Join Date
    Jul 2014
    Location
    NY
    Posts
    1,391
    Quote Originally Posted by the fat bastid View Post
    for the dash, i made this:


    so not only 6 illumination but if you are crazy, 10 more for the signals.
    the little blue ones ctrlraven thinks are t5s.
    I haven't pulled it apart yet.
    This is terrific! I have been looking for something like this for a while!

  7. #7
    Join Date
    Aug 2010
    Location
    Gadsden, Al
    Age
    49
    Posts
    2,370
    Good info

    Sent from my SAMSUNG-SM-G935A using Tapatalk
    2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.

    1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.

  8. #8
    Join Date
    Nov 2006
    Location
    Ogden Utah
    Age
    42
    Posts
    2,181
    Quote Originally Posted by the fat bastid View Post
    for the dash, i made this:


    so not only 6 illumination but if you are crazy, 10 more for the signals.
    the little blue ones ctrlraven thinks are t5s.
    I haven't pulled it apart yet.
    That is awesome! Good work, I never swapped my signal lights.
    2003 300A
    Build date 9/27/02
    Sequence# 5244 of 7839
    I have a few things done to it, Eaton swap next!
    1993 Ford Taurus SHO-Every bolt on available...Awaiting a Turbo
    2008 Ford F350 SD
    1974 Ford F350 SCS
    2011 Ford Flex Titanium, Ecoboost
    www.cardomain.com/id/shofast
    If you don't stand behind our troops; please feel free to stand in front of them!

  9. #9
    Headlight Switch - T4 Tall (if replacing with an LED bulb)
    Shifter - 168/194

    2004 Silver Birch
    300B
    Build date:9/29/2003, Adopted on 12/02/05
    Exhaust by Greg
    13.630 @ 100.49 mph (11/21/10)

    2015 Ford Focus SE Sport FWD
    2013 Lincoln MKS EcoBoost AWD (377whp/423tq).
    2010 Ford Fusion Sport FWD
    1989.5 Ford Mustang 5.0 LXsport

  10. #10
    Join Date
    Nov 2014
    Location
    KC
    Age
    48
    Posts
    3,511
    What is the part number for the upgraded LED bulbs inside the digital HVAC head unit?
    The twins2.3 whipple/aluminatorVortech V-2 lots of goodies

    Current marauders
    04 DTR totaled JUST NOW starting to part out 7-21-2021 https://youtu.be/REUxjP1BVpg

    04 Silver Birch Dark Charcoal Hardtop Whipple Supercharger
    04 Silver Birch Dark Charcoal Hardtop V2 Supercharger
    04 Silver Birch Dark Charcoal Converted
    03 DBP Light Flint #122
    03 DBP Dark Charcoal #232
    03 Silver Birch 300b Light Flint Going to fix er up
    03 Black 300a
    04 Silver Birch Dark Charcoal moonroof in the works

    04 Heaton Swapped DTR
    Joe's Wrecked DTR rebuild thread

  11. #11
    Join Date
    Jan 2004
    Location
    Somewhere in the N.C. Triangle
    Age
    68
    Posts
    26,250
    Quote Originally Posted by Turbov6Bryan View Post
    What is the part number for the upgraded LED bulbs inside the digital HVAC head unit?
    There are no "replaceable" bulbs as they are soldered in.

    I solder individual LEDs in place of the incandescent "wheat" bulbs for the buttons and I install an LED for the fan control wheel.
    Last edited by fastblackmerc; 10-21-2016 at 07:25 AM.
    “When you can’t make them see the light, make them feel the heat.”
    Ronald Regan

    "The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
    is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."

    Lt. Colonel Ralph Peters

    “Be polite, be professional, but have a plan to kill everybody you meet.”
    "I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
    General James Mattis




  12. #12
    Join Date
    Nov 2014
    Location
    KC
    Age
    48
    Posts
    3,511
    Quote Originally Posted by fastblackmerc View Post
    There is no "replaceable" bulbs as they are soldered in.

    I solder individual LEDs in place of the incandescent "wheat" bulbs for the buttons and I install an LED for the fan control wheel.
    The older digital board bulbs are soldered in place nearest the faceplate side, but I have 2 newer with removable bulbs in the face plate.

    They look like T5 bulbs that you can take out from the back side.

    I did not know there are 2 designs until last night. When you put LED bulbs in these are you doing white or green? I want to do 3 of my marauders this weekend.

    Thank you
    The twins2.3 whipple/aluminatorVortech V-2 lots of goodies

    Current marauders
    04 DTR totaled JUST NOW starting to part out 7-21-2021 https://youtu.be/REUxjP1BVpg

    04 Silver Birch Dark Charcoal Hardtop Whipple Supercharger
    04 Silver Birch Dark Charcoal Hardtop V2 Supercharger
    04 Silver Birch Dark Charcoal Converted
    03 DBP Light Flint #122
    03 DBP Dark Charcoal #232
    03 Silver Birch 300b Light Flint Going to fix er up
    03 Black 300a
    04 Silver Birch Dark Charcoal moonroof in the works

    04 Heaton Swapped DTR
    Joe's Wrecked DTR rebuild thread

  13. #13
    Join Date
    Jan 2004
    Location
    Somewhere in the N.C. Triangle
    Age
    68
    Posts
    26,250
    Quote Originally Posted by Turbov6Bryan View Post
    The older digital board bulbs are soldered in place nearest the faceplate side, but I have 2 newer with removable bulbs in the face plate.

    They look like T5 bulbs that you can take out from the back side.

    I did not know there are 2 designs until last night. When you put LED bulbs in these are you doing white or green? I want to do 3 of my marauders this weekend.

    Thank you
    Every single one (probably well over 100) I've done has had soldered bulbs.

    I can do either green or white LED's.
    “When you can’t make them see the light, make them feel the heat.”
    Ronald Regan

    "The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
    is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."

    Lt. Colonel Ralph Peters

    “Be polite, be professional, but have a plan to kill everybody you meet.”
    "I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
    General James Mattis




  14. #14
    Join Date
    Jan 2004
    Location
    Somewhere in the N.C. Triangle
    Age
    68
    Posts
    26,250
    Quote Originally Posted by Turbov6Bryan View Post
    The older digital board bulbs are soldered in place nearest the faceplate side, but I have 2 newer with removable bulbs in the face plate.

    They look like T5 bulbs that you can take out from the back side.

    I did not know there are 2 designs until last night. When you put LED bulbs in these are you doing white or green? I want to do 3 of my marauders this weekend.

    Thank you
    It would be interesting to see what the Ford P/N is on your EATC's.

    To my knowledge if your EATC bulbs are like this:


    And the solenoids are like this:


    Then you have an older EATC or an F150 EATC (yes they are the same and it's a BI**H to replace the o-rings but it can be done).

    If the bulbs are soldered in and the solenoids look like this:


    Then you have a newer unit.

    In any case, I can repair them all.
    Last edited by fastblackmerc; 10-21-2016 at 07:34 AM.
    “When you can’t make them see the light, make them feel the heat.”
    Ronald Regan

    "The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
    is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."

    Lt. Colonel Ralph Peters

    “Be polite, be professional, but have a plan to kill everybody you meet.”
    "I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
    General James Mattis




  15. #15
    Join Date
    Nov 2014
    Location
    KC
    Age
    48
    Posts
    3,511
    Ok cool. So in your opinion, which LED looks better? White or green?

    Ok, just opened both. Mm has solder lights, the one I repaired last night has removable light bulbs????? LOL. It's was in a 98 GM but the head unit is a 2005??

    Thoughts?
    Last edited by Turbov6Bryan; 01-08-2018 at 03:59 PM.
    The twins2.3 whipple/aluminatorVortech V-2 lots of goodies

    Current marauders
    04 DTR totaled JUST NOW starting to part out 7-21-2021 https://youtu.be/REUxjP1BVpg

    04 Silver Birch Dark Charcoal Hardtop Whipple Supercharger
    04 Silver Birch Dark Charcoal Hardtop V2 Supercharger
    04 Silver Birch Dark Charcoal Converted
    03 DBP Light Flint #122
    03 DBP Dark Charcoal #232
    03 Silver Birch 300b Light Flint Going to fix er up
    03 Black 300a
    04 Silver Birch Dark Charcoal moonroof in the works

    04 Heaton Swapped DTR
    Joe's Wrecked DTR rebuild thread

Page 1 of 3 123 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 2003 Marauder - Minnesota
    By crouse in forum Third Party Ads (Craigslist/eBay)
    Replies: 0
    Last Post: 10-06-2016, 02:19 PM
  2. For Sale 2003 Black Marauder for sale
    By lamont76 in forum Marauders for Sale
    Replies: 1
    Last Post: 10-02-2016, 11:47 PM
  3. For Sale 2003 Mercury Marauder with 83,000 miles - asking $6900
    By RSW in forum Marauders for Sale
    Replies: 2
    Last Post: 09-20-2015, 01:22 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •