I've used jb weld aluminum repair with excellent results. Just lightly sand after it sets up. I've used other stuff too, sets in a hour. Works fine too
I've used jb weld aluminum repair with excellent results. Just lightly sand after it sets up. I've used other stuff too, sets in a hour. Works fine too
The twins2.3 whipple/aluminatorVortech V-2 lots of goodies
Current marauders
04 DTR totaled JUST NOW starting to part out 7-21-2021 https://youtu.be/REUxjP1BVpg
04 Silver Birch Dark Charcoal Hardtop Whipple Supercharger
04 Silver Birch Dark Charcoal Hardtop V2 Supercharger
04 Silver Birch Dark Charcoal Converted
03 DBP Light Flint #122
03 DBP Dark Charcoal #232
03 Silver Birch 300b Light Flint Going to fix er up
03 Black 300a
04 Silver Birch Dark Charcoal moonroof in the works
04 Heaton Swapped DTR
Joe's Wrecked DTR rebuild thread
Didn’t think of that, but I was able to get a good coating of form-a-gasket stuff on both sides. For me there just isn’t any way to sand the block side of the housing, so I sc***** off any residue up there, cleaned it with acetone, then painted on the Permatex liquid.
You saved my butt with that zip tie trick, I don’t think I could have done it otherwise. I couldn’t see of course, but counted on the top and bottom bolt to line up the gasket on the housing. Now that I have it together I can see 1/64” of blue gasket peeking out the back edge, but it doesn’t appear to be leaking. I’ll know for sure after I replace the oil sending unit tonight.
P.S. Sorry see it was the instructional from Byronrace where he mentions the zip tie, to give proper credit!
Sent from my iPhone using Tapatalk
Last edited by Svashtar; 07-03-2019 at 08:10 AM.
2003 black pre-decontented 300B #5886 of 7838; Born on 10/31/02
MartyO tune, 4:10's, T/A stud & girdle, MMX shaft+DS loop, Metco control arms, Quickor RSB, Addco FSB, Megs delete tips, Granatelli solid coil connectors, NGK plugs & LP 170 stat, DR rear engine cooling mod, PI 3000 TC, Level II tranny, Art Carr deep pan, Steeda pullies/billet caps, billet door locks, Ford Racing oil cap / polished coil covers, PHP CAK & Metco carbon fiber intake, DG Motorsports CF radiator cover, Fumoto oil drain valve, oil deflector, real Autometer gauges, ScanGauge II, Weatherflectors, underbody lighting kit, Zack chrome grill, OEM spoiler & door edge guards, KB dead pedal, Dynopro aluminum sills & pedals, Viper alarm w/ remote start, MM fender badges, red painted calipers, SS inserts, Silverstar Ultras, hood bumpers, 35% tints, Gorilla lug nuts, MM valve caps, Pro-Guard, DD trunk lid liner, CM UHI kit, CM Godshead rear & steering wheel badges, S-55 badge, FilterMag, MM trunk bib, ported sub-woofer.
2003 black pre-decontented 300B #5886 of 7838; Born on 10/31/02
MartyO tune, 4:10's, T/A stud & girdle, MMX shaft+DS loop, Metco control arms, Quickor RSB, Addco FSB, Megs delete tips, Granatelli solid coil connectors, NGK plugs & LP 170 stat, DR rear engine cooling mod, PI 3000 TC, Level II tranny, Art Carr deep pan, Steeda pullies/billet caps, billet door locks, Ford Racing oil cap / polished coil covers, PHP CAK & Metco carbon fiber intake, DG Motorsports CF radiator cover, Fumoto oil drain valve, oil deflector, real Autometer gauges, ScanGauge II, Weatherflectors, underbody lighting kit, Zack chrome grill, OEM spoiler & door edge guards, KB dead pedal, Dynopro aluminum sills & pedals, Viper alarm w/ remote start, MM fender badges, red painted calipers, SS inserts, Silverstar Ultras, hood bumpers, 35% tints, Gorilla lug nuts, MM valve caps, Pro-Guard, DD trunk lid liner, CM UHI kit, CM Godshead rear & steering wheel badges, S-55 badge, FilterMag, MM trunk bib, ported sub-woofer.
There are currently 1 users browsing this thread. (0 members and 1 guests)