Hey guys, I wanna test my compressor before I spend the money on a new one, can anyone give me a step-by-step how to do it?
Sent from my 2PS64 using Tapatalk
Hey guys, I wanna test my compressor before I spend the money on a new one, can anyone give me a step-by-step how to do it?
Sent from my 2PS64 using Tapatalk
Give it positive and negative.
Do you want to just test if the compressor works or are you trying to jump it to fill the bags?
If you're trying to fill the bags, you need to make sure the solenoids open up which they'll only remain open for a certain window of time.
Normally when I was ever testing a car with a bad compressor, I'd just slap a known good compressor on since its so easy to change. You don't need the car running, just key on, open/close a door so it trips the solenoids open (as long as it isn't at ride height, you'll hear a click when they open), then you could jump the compressor to put air in the bags.
I have never had to jump a compressor before, if yours is dead and looks rusty 95% chance it's the problem. Happens to everyone at some point.
2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005
2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
2063/3214
(Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
5377/7838
2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB
1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors
At that point I'd just disconnect the airline and jump it.
I don't remember the pinout for our cars, these may be the same
https://www.crownvic.net/drock96marquis/RAS.htm
2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005
2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
2063/3214
(Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
5377/7838
2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB
1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors
2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005
2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
2063/3214
(Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
5377/7838
2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB
1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors
BK - Ground
PK - Solenoid vent
BK - Ground
GY/RD - Compressor relay, switched power
Sent from my iPhone using Tapatalk Pro
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
My compressor doesn't have the same colors you're describing. Held looking into the holes like in the first picture, the individual pinholes look like a compass ("North" being the hole closest to the connector clip), and their wire colors are as follows:
North-Red
East-Blue
South-Green
West-Black
Keeping this configuration in mind, can I run a jump wire from my car battery's (-) to the black(West) hole and another jump wire from car battery's (+) to the red(North) hole, with the car running, to properly test if this compressor will run anymore?
Sent from my 2PS64 using Tapatalk
My compressor doesn't have the same colors you're describing. Held looking into the holes like in the first picture, the individual pinholes look like a compass ("North" being the hole closest to the connector clip), and their wire colors are as follows:
North-Red
East-Blue
South-Green
West-Black
Keeping this configuration in mind, can I run a jump wire from my car battery's (-) to the black(West) hole and another jump wire from car battery's (+) to the red(North) hole, with the car running, to properly test if this compressor will run anymore?
Sent from my 2PS64 using Tapatalk
After seeing how crusty the motor is.. it's prolly toast..bench test it for piece of mind.
2004 SB Ported Trilogy 48
Has supporting mods and stuff
Thanks to Marty O for his help in updating this car.
R.I.P.
Rex "SC Cheesehead"
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
There are currently 1 users browsing this thread. (0 members and 1 guests)