I know I’m going to need exhaust. I ran across this kooks header with off-road x pipe for less than $700. Does this look like it would work? I’m in Alabama and we don’t have emissions testing. If not this, what do you recommend? I still have stock exhaust except for deleted rear cats.
https://wheelwell.com/shop/kooks-cus...&submodel=Base
Engine is out. Pulled it just as you guys suggested. Wasn’t bad at all. Will get it on a stand next week and start swapping everything over
Sent from my iPhone using Tapatalk
Last edited by JBeezy; 05-05-2019 at 12:20 PM.
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
I didn’t want to start a new thread so I’m posting here. I have a few questions. I have ordered a set of SW headers and plan on ordering an x pipe and exhaust this week. The questions I have are:
What is the best place to shop the o-rings that sit on the port behind the water pump? The metal tube that runs under the intake connects to it. The dealer wants $18 ea for them. Crazy to me
For those with SW headers, can they be installed while the engine is out and set in with the engine?
If so, will the steering shaft be an issue?
Also concerning the headers, can I use the factory dipstick? I want to say I read something about possibly cutting the header flange for this to work
Thanks in advance. That’s all I can think of at the moment
Sent from my iPhone using Tapatalk
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
Engine can be installed with headers on engine. Dipstick is your call. Some cut the flange so tube doesn't have to be removed and others use a Lokar flexible dipstick. I went the Lokar route for the ease.
You "feel" the difference because you want to "feel" the difference. Since you just spent money on the upgrade you "have" to feel the difference
I'm looking to eliminate the double pump process I have to follow right now to get the pedal hard
2004 300A Procharger #0010 D1X
2003 300A Procharger #0017 D1SC (SOLD. Last I heard, it was in Washington State)
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
You "feel" the difference because you want to "feel" the difference. Since you just spent money on the upgrade you "have" to feel the difference
I'm looking to eliminate the double pump process I have to follow right now to get the pedal hard
2004 300A Procharger #0010 D1X
2003 300A Procharger #0017 D1SC (SOLD. Last I heard, it was in Washington State)
It will be easier to install the engine with the SW headers bolted on, if you disconnect and move the steering shaft out of the way.
It may be possible to leave the shaft connected, but with Kooks headers I found it necessary to disconnect the steering shaft.
Looks good so far!
Also: Gotta love that friggin' anti-freeze!
No matter how much you drain and tilt the engine....it ALWAYS pukes out another quart or more of that sickly sweet, slippery coolant....
2020 Ford Ranger STX DFI Turbo 2.3L 10 speed Auto
2017 Ford Fusion Sport DFI Twin Turbo 2.7L V6 6 speed Auto (14.000 ET bone stock in 82 degree heat)
1985 Mustang GT 5.0 Hatchback 4bbl 5 speed manual (525 HP 363 Dart block/AFR heads with Magnum 6 speed in the works)
1984 Mustang GT 2.3 Turbo Convertible FI. 5 speed manual
1966 427 Cobra (ERA) 468 all Aluminum FE 2x4bbl 5 speed manual
SOLD : 2003 Mercury Marauder FI. 4 speed Auto
w/Crower Cams & Springs, +1mm SS valves, mild port job on the cylinder heads.
Extrude honed intake w/PHP spacer.
Kooks Headers w/2.5" High Flow Cats & X-Pipe, Magnaflow mufflers, OEM tailpipes w/Megs Tips
B&M Trans cooler w/fan, Level 10 Shift Kit, Art Carr Hughes Deep Sump Trans Pan,
SVO Rearend Girdle, Redline Gear lube; OEM 3.55s
'Real Gauges' + matching Trans Temp, Oil Temp, Water Temp, Fuel Pressure, Vacuum/Boost Gauge
Built: 10/15/02 Bought: 12/16/02 Sold: 10/15/18
IIRC the shaft is fine left in place. If I were you I’d cut down all the studs on the passenger side so you have the option of removing it later if need be. I don’t recall which ones won’t clear so I just cut them all.
Sent from my iPhone using Tapatalk Pro
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
Thanks Joe. I got it on a stand a few days ago and I tilted it tonight to remove the oil pan and even more antifreeze drained out. A lot more. I’m in the process of swapping everything over. Had to clean the nasty timing cover. The seal on the input shaft of the Procharger was pretty much resting against the pulley and causing a major leak.
Sent from my iPhone using Tapatalk
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
I had the same issue with my Procharger
You "feel" the difference because you want to "feel" the difference. Since you just spent money on the upgrade you "have" to feel the difference
I'm looking to eliminate the double pump process I have to follow right now to get the pedal hard
2004 300A Procharger #0010 D1X
2003 300A Procharger #0017 D1SC (SOLD. Last I heard, it was in Washington State)
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
Ouch. Luckily I caught it before catastrophic failure.
You "feel" the difference because you want to "feel" the difference. Since you just spent money on the upgrade you "have" to feel the difference
I'm looking to eliminate the double pump process I have to follow right now to get the pedal hard
2004 300A Procharger #0010 D1X
2003 300A Procharger #0017 D1SC (SOLD. Last I heard, it was in Washington State)
Mine has been leaking for a while but I never knew that is where it was leaking from. Knowing this o checked it every other time I drove the car, same with my oil. Idk why but better safe than sorry.
What did you do? Replace the seal yourself or send it off?
Sent from my iPhone using Tapatalk
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
There are currently 1 users browsing this thread. (0 members and 1 guests)