“When you can’t make them see the light, make them feel the heat.”
Ronald Regan
"The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."
Lt. Colonel Ralph Peters
“Be polite, be professional, but have a plan to kill everybody you meet.”
"I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
General James Mattis
Offroadkarter, I just want to know how do you know where to begin cutting on the housing to mount the new projector so that when it’s finished the projector is mounted in a manner that the actual headlight housing doesn’t have to be adjusted in an exaggerated manner to aim the light output that is very noticeable? Hopefully this question makes sense.
When I built the headlights for the red car I made the brackets to have adjustability on all 4 corners so I could level the projector out once it was in the car. Normally you'd shine the factory light against a wall (making sure the housing is level) and mark the beam. Then you mock the projector up and level out the beam to match and go from there.
When you use the Morimoto MH1 or D2S you don't have to worry about this as it just mounts where the stock 9007 bulb goes. You can rotate the projector straight and lock it down with the nut.
2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005
2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
2063/3214
(Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
5377/7838
2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB
1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors
Ok so the Miromoto mounts to a known flat surface? So adjustment is made in the OEM manner then?
2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005
2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
2063/3214
(Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
5377/7838
2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB
1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors
That’s awesome info. I really appreciate it. I’ve been considering lights from panther lights but it sounds like this is pretty easy for a diy project with the MH1 projectors.
2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005
2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
2063/3214
(Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
5377/7838
2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB
1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors
Sorry if this has already been answered, does anyone sell Marauder lights with projector mod or does anyone do the mod?
TY
WLB
BB#1) 1996 ImpalaSS - 16,500 miles - 100% stock
______________________________ ___________
BB#2) 2003 Marauder (300a) - 34k miles - Daily Driver
#2912 of 7093
Conceived 8/6/2002
Delivered 9/19/2002
Adopted 8/10/2011
Trilogy 242 - Self Installed 9/9/12 (0-60 5.5 sec)
Pioneer 6x8 Front
Legacy 600w 6x9 Rears
JL 6.5 SubWoofer
K&N CAI
Window tint 50% rear/35% front
FBM CHMSL with Strobe mod 7/1/12
DR Deep Aluminum Trans Pan
Sparta FOMOCO Racing 8.8 Girdle
Mo's Dyno Tune
Gorilla Nuts - The System
Ford Racing 4.10s, 31 spline Cobra carrier & axles 7/1/12
Powder Coat Axle Housing 7/1/12
CME HP Rear Control Arms & Watts Link 7/1/12
______________________________ ________________
Rex "SC Cheesehead" Weinbender 11-14-13
Ed "Baaad GN" Linthicum 8-6-2014
Panther lights
Sent from my iPhone using Tapatalk
2004 MM (Black) #112 of 3213 (SOLD)
2022 Ford Ff-150 SuperCab Iconic Silver "Powerboost"
3.35 L 4X4
-AND-
SLAYER1
formerly owned by "Impala Slayer!! 2004 SB MM
Kenne Belle 2.8 (Liquid Cooled), MMR "Boss 302" Block, L&M Engines rebuild Kooks Headers and cats, Accusump Pre-Oiler Dynamax VT mufflers, MBS 2 1/2" exhaust, 4.10's, 2800 stall, Argento 312 "Color" Powder coated wheels, Rears widened 1 1/2 "703
702 RWHP/653 RWTQ @ 21 Lbs. Boost, M/M catch can, 3 pillar gauge (Boost, Fuel, air intake and coolant temp, custom console cover, S-55 treatment etc...
Same retrofitted headlights as Panther Lights
On sale at Headlight Revolution for $99.50
https://headlightrevolution.com/star...rown-victoria/
You "feel" the difference because you want to "feel" the difference. Since you just spent money on the upgrade you "have" to feel the difference
I'm looking to eliminate the double pump process I have to follow right now to get the pedal hard
2004 300A Procharger #0010 D1X
2003 300A Procharger #0017 D1SC (SOLD. Last I heard, it was in Washington State)
Crown vic lights don't fit Marauders
2004 SB Ported Trilogy 48
Has supporting mods and stuff
Thanks to Marty O for his help in updating this car.
R.I.P.
Rex "SC Cheesehead"
2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005
2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
2063/3214
(Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
5377/7838
2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB
1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors
So I finally got around to installing the projector headlights. One of the best mods I have done highly recommend. Such an improvement night and day difference. Easy Peezy .
2004 marauder black purchased new. Sold 9/16 at 297,000 miles. Still ran strong didn't burn a drop of oil.
2003 marauder black 28,000 miles all stock. Garage Queen.
2004 marauder red daily driver.
I love my Vled's conversions, worst part about them is the little fan to cool the bulb makes noise but once you start the car you can't hear them. I like the stock headlights to much to run a projector type.
There are currently 1 users browsing this thread. (0 members and 1 guests)