View Poll Results: are you interested in a intake for the M122 style Super chargers?

Voters
4. You may not vote on this poll
  • Yes, definitely interested

    1 25.00%
  • No, don't want the extra power

    3 75.00%
Page 2 of 2 FirstFirst 12
Results 16 to 25 of 25

Thread: M122 Super Charger intake

  1. #16
    Join Date
    Jun 2011
    Location
    Northeast OH
    Posts
    7,999
    You will need new spacers for pulleys, new lower pulley. Trilogy and m122 have different snout lengths and the crossover tube for trilogy I don't believe works. Travis can prolly elaborate on these
    2004 SB Ported Trilogy 48
    Has supporting mods and stuff
    Thanks to Marty O for his help in updating this car.

    R.I.P.
    Rex "SC Cheesehead"

  2. #17
    Join Date
    Feb 2015
    Location
    Sumter SC
    Posts
    24
    Like me... Funny.
    I have been modding cars longer than I would like to remember. The point is, when you buy an after market item intake etc. and you then mod it in any way then it fails good luck warrantying it, then there are also other concerns.. I do not mind porting etc. but when you modify boss's and torque areas I have to say no.

    Thanks for clarifying that my lower intake will work with Cobra engineering parts. I will pursue this further..
    2004 Marauder
    2011 Shelby GT500 (Super Snake)
    2008 Ram 3500 Mega cab Cummins
    1971 Torino GT BB
    1970 Torino cpe BB
    1969 Fairlane Formal 428cj
    1968 Fairlane Formal 428PI
    3 Bronco II's
    1990 5 ton BMY M939 "Bobbed"
    1974 Land cruiser BJ40
    I think I have too many cars!

  3. #18
    Join Date
    Feb 2015
    Location
    Sumter SC
    Posts
    24
    @ RubberCTyRauder

    Thanks for the info, very helpful!
    2004 Marauder
    2011 Shelby GT500 (Super Snake)
    2008 Ram 3500 Mega cab Cummins
    1971 Torino GT BB
    1970 Torino cpe BB
    1969 Fairlane Formal 428cj
    1968 Fairlane Formal 428PI
    3 Bronco II's
    1990 5 ton BMY M939 "Bobbed"
    1974 Land cruiser BJ40
    I think I have too many cars!

  4. #19
    Join Date
    Sep 2006
    Location
    Psych ward
    Age
    53
    Posts
    1,081
    looks like a lot of cut and paste going on...…...
    • 82 GT coyote swap started
    • 03 300a Marauder, stroked,cammed,T/S Trilogy Supercharged # 216,Best Et 10.77@129.72 on slicks, 93 pump gas. driven to the track.
    • 2011 GT 500, 3.4 whipple,93 pump gas,10.47@133,Driven to the track.
    • 2003 azura blue Mach 1, cobra motor,2.9 Whipple,crusher inlet,built 4r70w trans,04 IRS rear.full weight street car, Corn Fed

  5. #20
    Join Date
    Jun 2011
    Location
    Northeast OH
    Posts
    7,999
    Also, do you have or planning on a built motor? Stock motor internals will be toast with a m122
    2004 SB Ported Trilogy 48
    Has supporting mods and stuff
    Thanks to Marty O for his help in updating this car.

    R.I.P.
    Rex "SC Cheesehead"

  6. #21
    Join Date
    Aug 2017
    Location
    Texas
    Posts
    261
    The Marauder heads are just like the Cobra heads only difference was the cams. From what I understand. If you're worried about the car original condition not being compromised. than keep it N/A. because even the trilogy kit requires you extend the alternator wires!

  7. #22
    Join Date
    Jun 2003
    Location
    Warson Woods, Missouri
    Age
    79
    Posts
    1,138
    Stiegemeier added a spacer in my Trilogy M112 together with the rotors from the M122. Also adjusted the upper pulley to keep the same belt position. Result was an increase in boost of about 4#. Is this a way to avoid spacers and still increase boost? Wednesday I ran 11.78 at 116.8. That was good for me.
    BUCKWHEAT 03 MM 300A-August, '02 mfgr, black w/ blue metallic clearcoat, 94,000 miles, Texid stroker 5.0, #15 Kool-Aide w/ SnakeBite porting, Venom cooling, and upgraded to M122, 3873 of 7839

  8. #23
    Join Date
    Jul 2004
    Location
    The Dirty South
    Age
    52
    Posts
    3,836
    Quote Originally Posted by BUCKWHEAT View Post
    Stiegemeier added a spacer in my Trilogy M112 together with the rotors from the M122. Also adjusted the upper pulley to keep the same belt position. Result was an increase in boost of about 4#. Is this a way to avoid spacers and still increase boost? Wednesday I ran 11.78 at 116.8. That was good for me.
    Hey Buckwheat I have a few questions I'd like to ask you.

    What was your upper/lower pulley combo before the rotor swap?
    What was your IAT with the old rotor pack?
    What PSI did the old pulley setup yield?

    What is your current pulley combo?
    Current PSI?
    Current IAT?

    Thanks!!!

  9. #24
    Join Date
    Jul 2004
    Location
    The Dirty South
    Age
    52
    Posts
    3,836
    Quote Originally Posted by Eastern_Front View Post
    Like me... Funny.
    I have been modding cars longer than I would like to remember. The point is, when you buy an after market item intake etc. and you then mod it in any way then it fails good luck warrantying it, then there are also other concerns.. I do not mind porting etc. but when you modify boss's and torque areas I have to say no.

    Thanks for clarifying that my lower intake will work with Cobra engineering parts. I will pursue this further..
    If you've been modding cars as long as you claim you know the aftermarket only offers a 30-90 day warranty on all parts.

    Don't waste your time following up on cobra engineering parts, as I stated earlier "I HAVE A GT500 SWAP USING THE COBRA ENGINEERING SWAP KIT" so if your worried about warranties, or damage to bosses when torqueing down bolts, this kit is NOT FOR YOU...….

  10. #25
    Join Date
    Jun 2003
    Location
    Warson Woods, Missouri
    Age
    79
    Posts
    1,138
    Quote Originally Posted by musclemerc View Post
    Hey Buckwheat I have a few questions I'd like to ask you.

    What was your upper/lower pulley combo before the rotor swap?
    What was your IAT with the old rotor pack?
    What PSI did the old pulley setup yield?

    What is your current pulley combo? Answer: Lower, for both is stock Trilogy. Upper before 3.6". After is 2.6 (from memory). Stiege said S/C speed was 18,000.
    Current PSI? Answer: Before: 10 on the gauge. After: 15, down to 13.5 (ish) at WOT
    Current IAT? Answer: Don't know in either case. No telemetry on IAT, but Marty did the relo on the measure for IAT between before and after.

    Thanks!!!
    Mine is Trilogy #15. I realize there are a lot oh floating variables here. And i am not the best Techie.
    BUCKWHEAT 03 MM 300A-August, '02 mfgr, black w/ blue metallic clearcoat, 94,000 miles, Texid stroker 5.0, #15 Kool-Aide w/ SnakeBite porting, Venom cooling, and upgraded to M122, 3873 of 7839

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Similar Threads

  1. super charger question
    By F2F in forum Power Adders
    Replies: 7
    Last Post: 04-25-2013, 08:27 PM
  2. For Sale Super Charger 2.8 & 3.0 Pulleys
    By Cobra25 in forum Marauder-specific Parts for Sale
    Replies: 10
    Last Post: 10-25-2011, 01:34 PM
  3. super charger
    By jay03merc in forum Trilogy Motorsports
    Replies: 5
    Last Post: 08-09-2006, 04:58 PM
  4. Ok...which Super Charger?
    By Mike M in forum Community Discussion
    Replies: 55
    Last Post: 05-25-2005, 03:35 PM
  5. super charger
    By seguns in forum Shop Talk
    Replies: 1
    Last Post: 07-24-2003, 08:16 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •