Results 1 to 15 of 15

Thread: 03 MM timing cover

  1. #1
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56

    03 MM timing cover

    Help, my AC guy over tightened one of the pulley bolts and cracked my timing cover. when I removed the pulley then put it back on the post the pulley rides on pulled off. No I didn't over tighten it, it came off very easy it must have been cracked before i removed it. I think the guy put to long of a bolt in it and it would not tighten so he put the impact gun on it, unfortunately it's been a year or so since he worked on it I think he will tell me to jump in a lake if I complained. where can I get one, I checked eBay with no luck, there are Dorman products for the SOHC but not for the DOHC. I don't think it can be welded but if that is my last hope I can try that. does anyone know if that part is aluminum or just pot metal? if pot metal I don't think it can be welded.
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

  2. #2
    Join Date
    Jul 2004
    Location
    The Dirty South
    Age
    48
    Posts
    3,699
    Cast aluminum

  3. #3
    Join Date
    Sep 2006
    Location
    Psych ward
    Age
    49
    Posts
    1,038
    I have one 150 plus the ride

    Let me know, shipping can be Costly from Canada
    • 82 GT coyote swap started
    • 03 300a Marauder, stroked,cammed,T/S Trilogy Supercharged # 216,Best Et 10.77@129.72 on slicks, 93 pump gas. driven to the track.
    • 2011 GT 500, 3.4 whipple,93 pump gas,10.47@133,Driven to the track.
    • 2003 azura blue Mach 1, cobra motor,2.9 Whipple,crusher inlet,built 4r70w trans,04 IRS rear.full weight street car, Corn Fed

  4. #4
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56
    what is Costly???
    it's not that heavy maybe a kg or so.... but the size is probably the driving factor
    I'm in sunny So Cal, Anaheim near Disneyland 92805 can you check the shipping cost?
    can you send a snap shot of it?

    Notice I used metric just for my friend from north of the border.....
    I'll pm you my email address so if you can send a pic send it direct.

    Sean
    Last edited by seanpatrick2000; 10-14-2020 at 09:05 PM.
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

  5. #5
    Join Date
    Mar 2008
    Location
    Next door to my neighbor
    Age
    47
    Posts
    19,625
    It can be welded and hold up just fine. But doing so will cost almost as much as replacing it and probably take longer.


    Sent from my iPhone using Tapatalk Pro


    Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.

  6. #6
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56
    I guess I should have called the ford dealer first, I thought the car was to old but they have them in the warehouse so I ordered one.
    if anyone needs one check the dealer they said they have 9 in stock.
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

  7. #7
    Join Date
    Aug 2011
    Location
    Wisconsin
    Posts
    3,991
    Quote Originally Posted by seanpatrick2000 View Post
    I guess I should have called the ford dealer first, I thought the car was to old but they have them in the warehouse so I ordered one.
    if anyone needs one check the dealer they said they have 9 in stock.
    3R3Z-6019-AA is a discontinued part. How much did you pay and what is dealers name and location?

    WLB
    BB#1) 1996 ImpalaSS - 16,500 miles - 100% stock
    ______________________________ ___________

    BB#2) 2003 Marauder (300a) - 34k miles - Daily Driver
    #2912 of 7093
    Conceived 8/6/2002
    Delivered 9/19/2002
    Adopted 8/10/2011
    Trilogy 242 - Self Installed 9/9/12 (0-60 5.5 sec)
    Pioneer 6x8 Front
    Legacy 600w 6x9 Rears
    JL 6.5 SubWoofer
    K&N CAI
    Window tint 50% rear/35% front
    FBM CHMSL with Strobe mod 7/1/12
    DR Deep Aluminum Trans Pan
    Sparta FOMOCO Racing 8.8 Girdle
    Mo's Dyno Tune
    Gorilla Nuts - The System
    Ford Racing 4.10s, 31 spline Cobra carrier & axles 7/1/12
    Powder Coat Axle Housing 7/1/12
    CME HP Rear Control Arms & Watts Link 7/1/12
    ______________________________ ________________

    Rex "SC Cheesehead" Weinbender 11-14-13
    Ed "Baaad GN" Linthicum 8-6-2014

  8. #8
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56
    he may have gotten me the wrong part, he sold me a 2w7z6019AB he showed me a picture and it was the timing cover. Villa Ford in Orange CA he said it is in the warehouse and will be in Monday. I am looking at the receipt and it says SPO COVER - Cylinder, he may have screwed up???
    I guess I'll see Monday
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

  9. #9
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56
    I googled the part number I have and it showed the timing cover at amazon.com
    https://www.amazon.com/Ford-2W7Z-601.../dp/B000NS0GT4
    I paid $151.25 maybe the part number you have is deprecated and this is the new part number???
    I don't know what to think, I guess I'll wait till Monday to find out

    he looked it up by the vin number of the car since he is a ford dealer not a mercury dealer??? strange I just googled it again
    and TASCA parts has it also
    https://www.tascaparts.com/oem-parts...z6019ab?c=az0x

    the picture looks right they are saying it's for SOHC so I am curious now the picture looks like the one on my MM DOHC

    oh I see the top is wider on the DOHC version, that idiot he looked it up from the vin number
    Last edited by seanpatrick2000; 10-16-2020 at 06:25 PM.
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

  10. #10
    Join Date
    Aug 2011
    Location
    Wisconsin
    Posts
    3,991
    It's a timing cover, make sure they commit that it will fit a Marauder. If it did, it would be listed on the Marauder parts breakdown instead of saying discontinued: https://www.tascaparts.com/oem-parts...Y4LWdhcw%3D%3D

    $160 on Amazon but Amazon says it does not fit a Maurauder: https://www.amazon.com/dp/B000NS0GT4...ype=automotive

    Good luck!

    WLB
    BB#1) 1996 ImpalaSS - 16,500 miles - 100% stock
    ______________________________ ___________

    BB#2) 2003 Marauder (300a) - 34k miles - Daily Driver
    #2912 of 7093
    Conceived 8/6/2002
    Delivered 9/19/2002
    Adopted 8/10/2011
    Trilogy 242 - Self Installed 9/9/12 (0-60 5.5 sec)
    Pioneer 6x8 Front
    Legacy 600w 6x9 Rears
    JL 6.5 SubWoofer
    K&N CAI
    Window tint 50% rear/35% front
    FBM CHMSL with Strobe mod 7/1/12
    DR Deep Aluminum Trans Pan
    Sparta FOMOCO Racing 8.8 Girdle
    Mo's Dyno Tune
    Gorilla Nuts - The System
    Ford Racing 4.10s, 31 spline Cobra carrier & axles 7/1/12
    Powder Coat Axle Housing 7/1/12
    CME HP Rear Control Arms & Watts Link 7/1/12
    ______________________________ ________________

    Rex "SC Cheesehead" Weinbender 11-14-13
    Ed "Baaad GN" Linthicum 8-6-2014

  11. #11
    Join Date
    Mar 2008
    Location
    Next door to my neighbor
    Age
    47
    Posts
    19,625
    Quote Originally Posted by seanpatrick2000 View Post
    I googled the part number I have and it showed the timing cover at amazon.com
    https://www.amazon.com/Ford-2W7Z-601.../dp/B000NS0GT4
    I paid $151.25 maybe the part number you have is deprecated and this is the new part number???
    I don't know what to think, I guess I'll wait till Monday to find out

    he looked it up by the vin number of the car since he is a ford dealer not a mercury dealer??? strange I just googled it again
    and TASCA parts has it also
    https://www.tascaparts.com/oem-parts...z6019ab?c=az0x

    the picture looks right they are saying it's for SOHC so I am curious now the picture looks like the one on my MM DOHC

    oh I see the top is wider on the DOHC version, that idiot he looked it up from the vin number
    Very typical that the parts department only show for a 2V, especially on 03s.


    Sent from my iPhone using Tapatalk Pro


    Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.

  12. #12
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56
    you would think that their data base would be better then that. but then again programmers are not that car smart, though I'm a programmer but I used to be an NIASE mechanic in a past career. shows my age, it's not NIASE anymore it's just ASE
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

  13. #13
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56
    the part I'm looking at is on ebay
    https://www.ebay.com/itm/New-2001-SV...sAAOSwwWpfSVW2

    it really looks like it is right and other people told me that 99-01 cobras will work and 03-04 mach 1 's will work so I wish
    i could be sure before I buy it.
    but thanks for the reply anyway
    Sean
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

  14. #14
    Join Date
    Jun 2007
    Location
    Bethlehem, PA
    Age
    39
    Posts
    2,820
    Did you find a timing cover? I have one on a core engine.
    2003 DBP # 153 Whipple 3.4 in coming soon
    2004 Black Trilogy #43

  15. #15
    Join Date
    Dec 2007
    Location
    Orange County Ca
    Posts
    56
    Not yet can you PM me?
    2003 Silver Birch Marauder tune by Marty, best $150 I ever spent

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Wanted To Buy Timing Cover
    By cobra3073 in forum Marauder Parts/Misc. Wanted
    Replies: 2
    Last Post: 03-15-2020, 12:12 PM
  2. Timing cover ?
    By Mr. Man in forum Shop Talk
    Replies: 1
    Last Post: 03-28-2016, 08:22 PM
  3. Cam Cover& Timing Cover swapability?
    By jwibbity in forum Shop Talk
    Replies: 7
    Last Post: 06-26-2014, 07:07 PM
  4. For Sale Timing Cover FS
    By FordNut in forum Marauder-specific Parts for Sale
    Replies: 4
    Last Post: 04-08-2010, 06:32 PM
  5. timing cover?
    By ImpalaSlayer in forum Shop Talk
    Replies: 4
    Last Post: 03-16-2009, 04:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •