Results 1 to 8 of 8

Thread: Locked out

  1. #1
    Join Date
    Oct 2008
    Location
    Toronto, ON
    Posts
    849

    Locked out

    I was doing some work on the old girl tonight, and I ended up locking myself out.
    The battery is disconnected and the hood is shut tight.
    The doors are all locked.
    The drivers door lock is super stiff, and the key does not turn counterclockwise in the door cylinder (lubing the door lock mechanism is one of the items I'm planning to do). It turns clockwise just fine. The power door works fine, when the battery is connected.
    I have the keys and can unlock the trunk no problem. I also have a jack and tools.

    How can I get inside the car?

    I'm thinking to try:

    1. Spraying lube into the door lock cylinder and down beneath the window felt until the mechanism is freed up.
    2. Find a batt+ wire somewhere in the trunk, and boost the car from there - it only needs to draw enough current to unlock the power door locks.
    3. Make a slim jim and try to open the door the old fashioned way - I've never done it before and have no actual idea how.

    Any help anyone offers is most appreciated.

  2. #2
    Join Date
    Mar 2008
    Location
    Next door to my neighbor
    Age
    50
    Posts
    20,353
    Can you reach up from under the battery to reconnect?


    Sent from my iPhone using Tapatalk Pro
    SOLD 12/31/2021

    Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.

  3. #3
    Join Date
    Mar 2007
    Location
    Lehigh Valley, PA
    Posts
    5,959
    I have never tried this but I have read in the past, if you pull the license plate light and apply 12v to the wires, you should be able to feed enough power into the car to get the RKE working again.

    https://www.m5board.com/threads/dead...unlock.577346/


    2016 Ford Mustang GT PP - Lund nGauge, BMR vertical links, MGW Shifter, BMR CB005

    2004 Mercury Marauder - Eaton M112, Billetflow 3.4, Accufab SBTB + Plenum, T-56 Magnum, 4.10s, Stainless Works LTs, 2.5" Exhaust, Borla Stingers, Ridetech Coilovers + Adj rear shocks, FX-R projectors, Wilwood 13" BNSL6 + FNSL4 BBKs, S55 Gauge Cluster
    440rwhp & 406rwtq Tuned by Adam @ Revolution Automotive
    2063/3214

    (Sold) 2003 Mercury Marauder - Stainless Works LT's, Stainless Works 2.5" Catback, JLT Intake, Mo's Xcal4 Tune
    5377/7838

    2000 BMW M5 - Evolve Intake, Evolve Alpha-N tune, Stoptech ST-40 BBK, UUC SSK, Dinan front STB, Dinan RSB

    1996 Ford Bronco - 4" lift, 35" BFG A/T's, Punisher Valve Body, MH1 Projectors

  4. #4
    Join Date
    Apr 2010
    Location
    South Florida
    Age
    34
    Posts
    1,874
    You can apply a power jump box to the starter.


    Sent from my iPhone using Tapatalk Pro

  5. #5
    Join Date
    Oct 2008
    Location
    Toronto, ON
    Posts
    849
    Thanks for the replies, gentlemen.

    I was able to hotwire the electrical system through the connector to the subwoofer amplifier of all things.

    C466 is a 6 pin connector that connects to a short pigtail which connects to the amplifier. Pin 6 is connected to always hot through a 25 amp fuse. I pulled the plug, removed the red pin locker and then pulled pin 6 (red/yellow wire on the car side, two solid yellow wires on the amplifier side). I pushed the lone pin back into the car-side harness, and used an alligator jumper to connect that pin to a red clamp of a jumper cable, connected the black one to some trunk sheet metal, and the other end to a 2nd battery (in another car). Wiggled the connections a bit while repeatedly pressing the unlock button on the remote until... thwip!

  6. #6
    Join Date
    Feb 2007
    Location
    Winston Salem, NC
    Posts
    775
    That was FASCINATING fix discoveries! Thanks for sharing folks!
    2003 300A
    Widened Rear Wheels with 295 45 Nitto G2's
    Eaton Swapped by Curless
    Brake Upgrade
    Mo's Tune
    JLT Intake
    Addco Sway Bars
    ADTR Coil Over Suspension
    Metco Control Arms & Watts Link
    SW Headers and Exhaust
    Accessories By FastBlackMerc
    4.10 Gears
    Aeroforce Gauges
    Pantherlights Headlamps

  7. #7
    Join Date
    Oct 2005
    Location
    Southwest Florida, Lee County
    Age
    54
    Posts
    3,423
    I'm a locksmith so telling you to wedge the rear door weatherstripping and slide a Z tool onto the horizontal lock rod towards the front of the car until the bellcrank lifts the lock button is probably too sophisticated.
    '04 Silver Marauder w/ sunroof - HID lighting, JL Audio / Eclipse DVD/NAV/iPod/camera, 4.10's, 2" drop, Progard Bumper Baffle, Delete tips, Billet Pedals, BC4E dead pedal, Lidio Tune, Mach1 chin spoiler, K&N CAI, TCE lines, Super40's, tinted tails, SS Inserts, Heinous Control Arms, Real oil gauge, lighted door handles. Currently installing Eaton M112.

    2004 Mercury Marauder
    Born March 2004, adopted October 2005. Sold January 2012, adopted AGAIN January 2016
    2,187 of 3,214
    997 in Silver Birch
    448 with light flint interior
    304 with heated seats
    336 with sunroof

  8. #8
    Join Date
    Aug 2011
    Location
    Wisconsin
    Posts
    4,338
    Quote Originally Posted by BAD MERC View Post
    I'm a locksmith so telling you to wedge the rear door weatherstripping and slide a Z tool onto the horizontal lock rod towards the front of the car until the bellcrank lifts the lock button is probably too sophisticated.
    Nope, done it a million times...

    WLB
    BB#1) 1996 ImpalaSS - 16,500 miles - 100% stock
    ______________________________ ___________

    BB#2) 2003 Marauder (300a) - 34k miles - Daily Driver
    #2912 of 7093
    Conceived 8/6/2002
    Delivered 9/19/2002
    Adopted 8/10/2011
    Trilogy 242 - Self Installed 9/9/12 (0-60 5.5 sec)
    Pioneer 6x8 Front
    Legacy 600w 6x9 Rears
    JL 6.5 SubWoofer
    K&N CAI
    Window tint 50% rear/35% front
    FBM CHMSL with Strobe mod 7/1/12
    DR Deep Aluminum Trans Pan
    Sparta FOMOCO Racing 8.8 Girdle
    Mo's Dyno Tune
    Gorilla Nuts - The System
    Ford Racing 4.10s, 31 spline Cobra carrier & axles 7/1/12
    Powder Coat Axle Housing 7/1/12
    CME HP Rear Control Arms & Watts Link 7/1/12
    ______________________________ ________________

    Rex "SC Cheesehead" Weinbender 11-14-13
    Ed "Baaad GN" Linthicum 8-6-2014

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Remove a locked lug nut
    By BLACKMARAUDER04 in forum Shop Talk
    Replies: 5
    Last Post: 05-23-2021, 04:52 AM
  2. Locked And Loaded!!
    By MM2004 in forum Kentucky Regional Spring Meet 2019
    Replies: 8
    Last Post: 04-01-2014, 08:15 AM
  3. possible locked engine
    By poboy26 in forum Community Discussion
    Replies: 8
    Last Post: 12-10-2013, 10:40 PM
  4. Every one of my posts are getting locked.
    By Aren Jay in forum The Lounge
    Replies: 7
    Last Post: 07-15-2009, 11:53 AM
  5. I'm locked out
    By Motorhead350 in forum The Lounge
    Replies: 20
    Last Post: 05-12-2008, 05:41 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •