Results 1 to 5 of 5

Thread: Hi

  1. 07-05-2022, 02:53 AM #1
    BeeDamn's Avatar
    BeeDamn
    BeeDamn is offline Maraudest
    Join Date
    May 2013
    Location
    Saudi Arabia
    Age
    34
    Posts
    403

    Question Hi

    Hi

    It's been a while and I hope everybody is allright ! So I was working with my brother on the Marauder and we finished rebuilding the entire engine and putting the Whipple with everything together (Thanks to you gents and this awesome forum).

    However, When we crank it for the first time we notice the RPM Is always High (Like 4000 rpm+) The throttle position is close ! But the RPM Is not getting any less than that !
    I tried and checked the Whipple bypass actuator Valve and its functioning OK. And it's getting lower a bit only if I disconnect ALL The whipple vacuum lines !

    So my question, Is this normal since the car need to be programmed first before cranking ?

    Need your help gentlemen, As I'm sure I'm going to face issues in start-up ! But I have big faith in you gentlemen !

    I well post pics soon.
    Last edited by BeeDamn; 07-22-2022 at 03:54 PM.
    EATON SWAP ONGOING LIST !!!!!!!!!

    Eaton M112 Supercharger ✓
    Intercooler ✓
    Lower intake plenum ✓
    Coolant Intake Manifold ✓
    TB Intake Plenum ✓
    Throttle Body ✓
    Cobra air intake tube ✓
    Accelerator cable bracket ✓
    Fuel rails ✓
    39lb. injectors ✓
    Cobra heat exchanger ✓
    lower Metco pulley with hub ✓
    Intercooler reservoir ✓
    90mm Lightning MAF ✓
    MAF to filter adapter plate ✓
    Conical air filter ✓
    Custom Bracket for Intercooler Reservoir ✓
    Custom Gortch Brackets ✓
    Heat Exchanger brackets ✓
    Intercooler pump ✓
    Intercooler pump wiring pigtail ✓
    Intercooler pump bracket ✓
    Ribbed idler pulley ✓
    Belt tensioner ✓
    Alternator Pulley ✓
    Fuel Pump ✓
    EGR delete kit ✓
    New accessory belt ✓
    Cooling tube ✓
    IAT sensor ✓
    Reply With Quote Reply With Quote
  2. 07-05-2022, 02:57 AM #2
    BeeDamn's Avatar
    BeeDamn
    BeeDamn is offline Maraudest
    Join Date
    May 2013
    Location
    Saudi Arabia
    Age
    34
    Posts
    403
    Thanks for the suggestion ! I'm currently working on a Tune with Marty, I'll update the work progress, And will post here
    Last edited by BeeDamn; 07-22-2022 at 03:57 PM.
    EATON SWAP ONGOING LIST !!!!!!!!!

    Eaton M112 Supercharger ✓
    Intercooler ✓
    Lower intake plenum ✓
    Coolant Intake Manifold ✓
    TB Intake Plenum ✓
    Throttle Body ✓
    Cobra air intake tube ✓
    Accelerator cable bracket ✓
    Fuel rails ✓
    39lb. injectors ✓
    Cobra heat exchanger ✓
    lower Metco pulley with hub ✓
    Intercooler reservoir ✓
    90mm Lightning MAF ✓
    MAF to filter adapter plate ✓
    Conical air filter ✓
    Custom Bracket for Intercooler Reservoir ✓
    Custom Gortch Brackets ✓
    Heat Exchanger brackets ✓
    Intercooler pump ✓
    Intercooler pump wiring pigtail ✓
    Intercooler pump bracket ✓
    Ribbed idler pulley ✓
    Belt tensioner ✓
    Alternator Pulley ✓
    Fuel Pump ✓
    EGR delete kit ✓
    New accessory belt ✓
    Cooling tube ✓
    IAT sensor ✓
    Reply With Quote Reply With Quote
  3. 07-24-2022, 06:51 AM #3
    Turbov6Bryan's Avatar
    Turbov6Bryan
    Turbov6Bryan is offline I miss whitey here
    Join Date
    Nov 2014
    Location
    KC
    Age
    48
    Posts
    3,518
    you have a vacuum leak after the throttle body, say..... intake manifold gasket? blower to intake gasket?
    The twins2.3 whipple/aluminatorVortech V-2 lots of goodies

    Current marauders
    04 DTR totaled JUST NOW starting to part out 7-21-2021 https://youtu.be/REUxjP1BVpg

    04 Silver Birch Dark Charcoal Hardtop Whipple Supercharger
    04 Silver Birch Dark Charcoal Hardtop V2 Supercharger
    04 Silver Birch Dark Charcoal Converted
    03 DBP Light Flint #122
    03 DBP Dark Charcoal #232
    03 Silver Birch 300b Light Flint Going to fix er up
    03 Black 300a
    04 Silver Birch Dark Charcoal moonroof in the works

    04 Heaton Swapped DTR
    Joe's Wrecked DTR rebuild thread
    Reply With Quote Reply With Quote
  4. 07-24-2022, 09:59 AM #4
    justbob's Avatar
    justbob
    justbob is offline Sick-Speed play toy
    Join Date
    Mar 2008
    Location
    Next door to my neighbor
    Age
    50
    Posts
    20,353
    Is the IAC mounted backwards?


    Sent from my iPhone using Tapatalk Pro
    SOLD 12/31/2021

    Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
    Reply With Quote Reply With Quote
  5. 07-25-2022, 07:24 AM #5
    Blown3.8's Avatar
    Blown3.8
    Blown3.8 is offline Mr. Hankey
    Join Date
    Sep 2004
    Location
    Woodbridge, VA
    Posts
    1,623
    What Bob said.
    ~Chris
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules