Thank you guys, I may go with LFP THANKS Mr.RaceX
But anybody know the approx weight I mean roughly how much it's weight ? is it that heavy !! I don't wanna spend alot on the shipping cost to my country
Thanks.
Maraudest
Thank you guys, I may go with LFP THANKS Mr.RaceX
But anybody know the approx weight I mean roughly how much it's weight ? is it that heavy !! I don't wanna spend alot on the shipping cost to my country
Thanks.
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Senior Member
For anyone that gets the full, high HP Eaton bracket from Jerry, there is an additional pulley on the back of the bracket that the accessory belt runs up and over. The belt I used is: 6PK2540 or a 6rib 100.75" belt.
P.S. If anyone ever runs a 6lb Lower and 3.0/2.93 Upper with this:
K080550HD Green Stripe works great
11.931 @ 116.33 (MT ET Streets)
12.073 @ 118.43 (Nitto 555)
I love the smell of Nitromethane and rubber in the morning!
Drag racers prayer:
As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen
Senior Member
anyone using the 4" cobra maf adapter from LFP? If so, what filter would I need. I bought the kn re-0870 and the flange wouldn't fit around ring
Sent from my iPhone using Tapatalk
'Just Live'
Supporting Vendor
Thanks for posting up the infoOriginally Posted by RacerX
For anyone that gets the full, high HP Eaton bracket from Jerry, there is an additional pulley on the back of the bracket that the accessory belt runs up and over. The belt I used is: 6PK2540 or a 6rib 100.75" belt.
P.S. If anyone ever runs a 6lb Lower and 3.0/2.93 Upper with this:
K080550HD Green Stripe works great
Those were the days.........
DANG THEY'RE CUTE!!!!!!
Smile and Nod
I love THIS bar
Sick-Speed play toy
Sent from my iPhone using Tapatalk
Best bang for the buck I've found is the 4" one at Advance auto. Spectre brand.
Builder Of Badassery
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
Senior Member
Anyone using the cobra lower pulley hub?(metco) Having alignment issues with the blower pulley, it doesn't sit flush against the crank pulley.
Sent from my iPhone using Tapatalk
Last edited by silversnake; 03-29-2015 at 02:20 PM.
'Just Live'
Senior Member
FYI the Cobra valley coolant tube/heater tube is only available at a few dealers across the country, less than 10 of them left.
I eat apples until my stomach feels much more full than its normal.
Maraudest
Guys I can't understand what pulley I need for the eaton swap ?
Is the stock idler smooth pulley OK ?
Do I need to change the alternator pulley to ribbed one or install it backward ?
Is the stock Belt tensioner OK ? or need the ribbed one too ?
I'm really confused about the pulleys I already got the upper and the lower pulley.
Sorry for asking too much I'm in the last process to complete my eaton swap parts
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Sick-Speed play toy
All that info is in the very first post.
Builder Of Badassery
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
Maraudest
Thanks bob
one more question! Does this COT fit the swap? one for MACH 1 and the other is for 96-98 COBRA!
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Senior Member
So how is the above list looking guys,it looks like I am the next to do the swap.
I just picked up a low mile M112 along with the ,TB,intake tube,fuel rail,factory injectors,factory cobra fuel pump not sure if it fits our cars.
Over the next few months I'll gather up what's missing and plan my install when the parts list is complete.if any one has a lead on a intake manifold or any other parts feel free to private message me.
Thanks
Tony
Senior Member
Hi
Did anything ever come of this ??
Thanks
Tony
Junior Member
O'm thinking about starting to collect swap parts, but what about the transmission? What does it need to hold all of this?
Weißbirke Plünderer
Trans is fine to 450+ hp
2004 SB Ported Trilogy 48
Has supporting mods and stuff
Thanks to Marty O for his help in updating this car.
R.I.P.
Rex "SC Cheesehead"
Sick-Speed play toy
Or more.🏻
Sent from my iThrone using Tapatalk
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
