Does anyone know how to replace the stud??
Does anyone know how to replace the stud??
i just put my factory studs back in, i had to pull my axles to get the studs out (i had 3inch studs installed) ,but with the axles on i dont think there is enuff room to pull the stud from the axle flange
04 MERCURY MARAUDER build date:02/11/04ITS ALIVE !!!!!!!!
STAY TUNED!!!!!!!!!!
**WHIPPLE 4.0L CRUSHER!**0000 (FOR NOW) RWHP
VISIT MY GARAGE FOR A FULL LIST OF MODS
How does the axle come off?
open the dif cover, pull the center pin, its help in with a small bolt on the LSD. push the axle in from the out sideremove c clip, pull axle out. be careful of the axle seal when removing and reinstalling the axle or you will be getting very good at this. reverse steps to reinstall and fill with lube
2010 fusion se
I had to change a axle stud a few years ago due to loose lug nuts and then the rim vibrating and snapping a stud. If you remove the brake rotor, there is a area in the parking brake assembly that will give you enough clearance to pop the old stud out and slide a new one in.
This was about 5yrs ago so I'm 99% positive that's exactly how I did it. The first time I had the rear apart to remove axles were when I did the gear swap which was much later on.
2003 MERCURY MARAUDER 300A
Build Date
5/31/02
Sequence#
#363 of 7839 Black Marauders
Dyno tested power
450 RWHP & 405 RWTQ on 93 octane
Best 1/4 mile time to date
12.456@109mph
Visit my Garage
Blackened300a's Garage
even better!, and less work i never changed studs with axles in
04 MERCURY MARAUDER build date:02/11/04ITS ALIVE !!!!!!!!
STAY TUNED!!!!!!!!!!
**WHIPPLE 4.0L CRUSHER!**0000 (FOR NOW) RWHP
VISIT MY GARAGE FOR A FULL LIST OF MODS
i wouldnt wana bang on the axle when it still installed but thats just me
2010 fusion se
The ABS ring will take the most beating against the back plate, the "C" clip shouldn't be affected.
2003 MERCURY MARAUDER 300A
Build Date
5/31/02
Sequence#
#363 of 7839 Black Marauders
Dyno tested power
450 RWHP & 405 RWTQ on 93 octane
Best 1/4 mile time to date
12.456@109mph
Visit my Garage
Blackened300a's Garage
the axle doesnt go in that far , the c clip is going to take that beating
04 MERCURY MARAUDER build date:02/11/04ITS ALIVE !!!!!!!!
STAY TUNED!!!!!!!!!!
**WHIPPLE 4.0L CRUSHER!**0000 (FOR NOW) RWHP
VISIT MY GARAGE FOR A FULL LIST OF MODS
well i agree in part, the s spring does not retain the c clips, the center pin limits the axles from moving in enuff to release the c clips
the s spring keeps tension on the clucth packs
04 MERCURY MARAUDER build date:02/11/04ITS ALIVE !!!!!!!!
STAY TUNED!!!!!!!!!!
**WHIPPLE 4.0L CRUSHER!**0000 (FOR NOW) RWHP
VISIT MY GARAGE FOR A FULL LIST OF MODS
2003 MERCURY MARAUDER 300A
Build Date
5/31/02
Sequence#
#363 of 7839 Black Marauders
Dyno tested power
450 RWHP & 405 RWTQ on 93 octane
Best 1/4 mile time to date
12.456@109mph
Visit my Garage
Blackened300a's Garage
You can drive out a rear stud and put another one in without removing the axle shafts there is enough room.
For pulling the new one back through you should get a good size washer that goes around the stud and a lug nut that is not caped on the end to get the new one out all the way and seated.
Just going to be a pain using a hand tool instead of an impact gun.
Bought Her for my 40th B Day in August of 2004 @ Crest Lincoln Mercury
Assembled 12/17/2003
#1183 of a build of 3214
and is #379 of 1237
Link to Mod's and car:
http://www.mercurymarauder.net/forum...o=view&id=8832
Link to Pictures of the Kids/Animals, Cars I have built or a hand in building as well as cars and trucks I have owned.
http://www.mercurymarauder.net/forum...php?albumid=16
There are currently 1 users browsing this thread. (0 members and 1 guests)