Can anyone estimate numbers for HP and torque (on a stock car) after a Diablo chip, Steeda pulleys, and Ford 4.10's? Thanks.
Can anyone estimate numbers for HP and torque (on a stock car) after a Diablo chip, Steeda pulleys, and Ford 4.10's? Thanks.
The 4.10's well do nothing for TRQ or HP
But most chips are good for 25 to 30 HP<-- this is only an avg each vehicle is differant and the pulleys are around 10 to 15 again avg for other Cobra owners out there
So around 40 to 45 HP at the crank.
Accufab 65mm Throttlebody, 4.10 gears, and JDM Flipchip. Finally here.
In the future: total custom Twin Turbo at 15-18 PSI
with Intercooler and 2003 Cobra Mustang lower end with Crank,Manley Rods, and 8.5 over1 Pistons.
14.976 @ 94.8 MPH 03 Marauder stock
13.028 @ 104.6 MPH 02 Lightning JDM Flipchip,4# lower pulley, and Borla Catback. JLP Ramair, Oilbreather, JLP power pipe
More to come
262 RWHP is what several have seen w/ this set up.
1/4 Mile Time 11.542 @ 121.19 MPH
195,000 Miles & 275+ Runs Down the 1,320’
541.57 RWHP & 476.64 RWTQ on DynoJet
Tuned by Aric at Injected Engineering
Vortech Super Charger V-2 “T” Trim, 19 PSI
8 Rib Belt, Innovators West 10% Overdrive Dampner
Air to Air Intercooler, Mini-race Bypass
Ford Cobra Remanufactured Long Block
Snow Performance Water-Methanol Injection
Kooks Headers & X Pipe
GT MAF, 60lb injectors, Dash 8, Aero Rails, Twin Ford GT Pumps,
Kinsler Fuel Filter, Kenne Bell Boost-A-Pump
Monroe Sensatrac, Metco Control Arms, Addco Rear Sway Bar
31 Ford Spline Axles & Detroit Truetrac, 4:10 Ford Racing Gears
Dynotech MMC Driveshaft
A-1 Performance Trans, Forced Tailshaft Lube, Carbon Clutches
3,500 RPM Stall Precision Industries Torque Converter
B&M Deep Finned Trans Pan
AeroForce Scan Gauges , Auto Meter Oil, Fuel & Boost Gauges
Kenny Brown Dead Pedal, 35% Tint, Silver Star Head Lights
AutoPage Alarm RS-727LCD, Boston Acoustic NX87
What he saidOriginally Posted by sailsmen
Talk about good timing...I have a solid answer:
Jacki (JBR927) just dynoed yesterday with us with that very same setup.
Her baseline was 253 rwhp. After Jerry W.'s magic, he adjusted a/f and this and that, and her final numbers were 268 rwhp. Needless to say, after a test drive, she was very pleased.
My numbers were similiar, but with the addition of a complete Kooks setup to this scenario will pull over 300 hp.
2017 Niro
Most of the trends on this site have quoted 8-12 hp & torq with the Steeda Pullys. If you do the DR. Chip,Denso's and 180 stat, you'll get an average of 23 hp.& 30 Torq. The 410's will make a big difference in your take off. If you do the DR. Stage 1 Chip do the Rear gears at the same time so the Chip can be programed ( Burned) for the gears.Originally Posted by BlackHole
There are currently 1 users browsing this thread. (0 members and 1 guests)