Been searching and can not find the answer anywhere I know I read the reason once, but why exactly can we not run a #6 lower?
free, wild and young
Been searching and can not find the answer anywhere I know I read the reason once, but why exactly can we not run a #6 lower?
If it's cheap and reliable it isn't fast
If it's cheap and fast it isn't reliable
If it's fast and reliable it isn't cheap
Supporting Vendor
I believe bill runs that. Using a tensioner bracket like thisOriginally Posted by blkZooM
image.jpg
Those were the days.........
DANG THEY'RE CUTE!!!!!!
Smile and Nod
I love THIS bar
free, wild and young
Thanks Lji372, I know the bracket needed to run the #6 lower, trying to figure out exactly why we need to use these instead of the normal ones is is belt slippage?
If it's cheap and reliable it isn't fast
If it's cheap and fast it isn't reliable
If it's fast and reliable it isn't cheap
Junior Member
Is the cobra aftercooler needed for this swap
Maraudest
guys is this the correct bracket for the eaton swap ?
SEE LINK
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Senior Member
No. Jerry has the ones u need
'Just Live'
Maraudest
Thank you Mr.silversnake !
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Supporting Vendor
HELLO!!!!!!!!!
DANG THEY'RE CUTE!!!!!!
Smile and Nod
I love THIS bar
Maraudest
Guys i'm thinking of buyn a JLT for our MM, but when I swap to Eaton, do I have to buy a CAI for the cobra too? or the MM CAI well fit just fine.
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Senior Member
JLT will not work after eaton swap, you could possibly buy a cobra JLT to use after the swap.
Or find a stock cobra intake tube, that's what myself and alot of other eaton swappers have
Maraudest
OK guys I already have the cobra 90mm maf do I still need the SCT BA-3000 maf also?
If so please explain in simple
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Sick-Speed play toy
No.
Builder Of Badassery
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
Maraudest
Thanks, but here's another questionI need a crank pully kit but I'm confused with these tow pulleys!
One is for F-150 Lighting and the other is for the Cobra !!
Is there's a different ? I see the diffrent only in some metal pieces, Is that really matter ? I already have the upper pulley BTW.
Sorry for asking again and again but I search and couldn't find an answer for it
Thanks
EATON SWAP ONGOING LIST !!!!!!!!!
Eaton M112 Supercharger ✓
Intercooler ✓
Lower intake plenum ✓
Coolant Intake Manifold ✓
TB Intake Plenum ✓
Throttle Body ✓
Cobra air intake tube ✓
Accelerator cable bracket ✓
Fuel rails ✓
39lb. injectors ✓
Cobra heat exchanger ✓
lower Metco pulley with hub ✓
Intercooler reservoir ✓
90mm Lightning MAF ✓
MAF to filter adapter plate ✓
Conical air filter ✓
Custom Bracket for Intercooler Reservoir ✓
Custom Gortch Brackets ✓
Heat Exchanger brackets ✓
Intercooler pump ✓
Intercooler pump wiring pigtail ✓
Intercooler pump bracket ✓
Ribbed idler pulley ✓
Belt tensioner ✓
Alternator Pulley ✓
Fuel Pump ✓
EGR delete kit ✓
New accessory belt ✓
Cooling tube ✓
IAT sensor ✓
Senior Member
You want the Cobra one. A few members are even running this setup https://www.lightningforceperformanc...ang_Cobra.html . I believe Mo's is a vendor for the LFP products.
2003 300A #5377 130,XXX Miles
Drilled and slotted rotors from Ebay
JLT
Stainless Works Long Tube Headers and 3" catback.
Mo's Tune
Senior Member
11.64 @ 129.85 (M&H DR's)
11.931 @ 116.33 (MT ET Streets)
12.073 @ 118.43 (Nitto 555)
I love the smell of Nitromethane and rubber in the morning!
Drag racers prayer:
As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen
There are currently 5 users browsing this thread. (0 members and 5 guests)
Posting Permissions
Reply With Quote
