I hope you used a new bearing to press on for final assembly after you determined your shim thickness. If not, that race is going to spin on the pinion while driving and ruin the gear set, as well as everything else in the axle in no time.
I hope you used a new bearing to press on for final assembly after you determined your shim thickness. If not, that race is going to spin on the pinion while driving and ruin the gear set, as well as everything else in the axle in no time.
Oh of course, I forgot to mention that. This bearing is strictly for fitting the pinion shims to save me hours total.
Not that I know of. There are a few guys here and there around the bay area, but no meet ups or clubs as far as I know. You're pretty handy with a set of tools. If I ever need any mechanical advice, I know who I'm callin on haha. By the time you get done with this, you'll know the car inside and out.
2003 Black 300A
Adopted: 4/26/14
Mods:
Mo's Tune - K&N CAI - 4.10 FOMOCO gears - Reische 170* T-stat - NGK TR6 Plugs - Flowmaster 40s - MuscleMerc's 3" Fuel Filter Mod - Addco Front and Rear Sway Bars - TCE SS Brake Lines - Cooper RS3-G1 - Factory Spoiler - SS Bumper Inserts
Lol I know right? I like knowing though, that way there are less questions wondering in my head lol.
Before anything else, is there a representative from thump racing on here?
Anyways
Ok so little update, finally finished the rear end, got my rod in, or the last piston /rod into the block and started throwing the heads on.
Cleaning up the rockers and installing them, only "special tool" I used was a flat head... Lol
I ran into an issue where the crank sprocket with the timing kit didn't have a boss/offset one one side, which would cause the trigger wheel to hit the chain. Just ended up getting a new one from ford.
So now it's time to degree the cams. I have the a bunch of the special tools to hold the cams and whatnot, but completely forgot about a degreeing wheel, and a TDC piston stop. Thank God for printers and cardboard! Lol
I'm currently making a piston stop tool aswell -
To be continued...
Last edited by minimarine09; 12-30-2017 at 09:41 AM.
It's very interesting to follow your build progress. Thoroughly enjoy the commentary and photos. Surprising how much you can learn from a thread like this
Thank You for sharing.
2004 Mercury Marauder - Silver Birch
2003 Mercury Marauder - Dark Blue Pearl
2003 Mercury Grand Marquis LS - Aspen Green
2002 Ford F150 Crew Cab - Silver Metallic
1997 Ford F150 4x4 - Vermillion Red - Silver Frost
Ok so I got some work done on the engine, cams degreed, some parts painted, had allot of issues with windage tray clearance but I got it dialed in now.
Got my 2013 gt500 injectors in, but unfortunately they are about 12mm too short, so I have some hat spacers on the way.
So my thump tensioner boss was in the wrong location, I guess the mach 1s are slightly different, so the thump tech support tools me to just drill and tap for an 8mm bolt where the dowel needs to be,
So I did and I was extremely nervous drilling into this expensive tensioner lol
The head of the bolt was still a bit too big for the hole in the front cover, so ever so slightly south a cutting wheel, I ground it down to a perfect snug fit. Way better than the dowel that came on it! If you look closely you can see where the old one was (the pulley in this picture was on backwards, dont do that...)
Last edited by minimarine09; 12-30-2017 at 09:54 AM.
So I got my cooling mod set up, and engine mostly dressed,
I still have to re remove the dampener because I didn't grind down the crank position Sensor boss far enough, kind of nervous to go through, but I guess if I do, it's nothing a little jb weld can't fix lol
And I love my punisher egr delete plate. I want to make my oil cap and coolant cap with the same design, might be the cars name! Punisherauder! Lol
Hopefully drop her in tomorrow if I have time
Last edited by minimarine09; 12-30-2017 at 10:03 AM.
Superb work sir
Sent from my SM-G950U using Tapatalk
Build# 1979/3214
Year 2004
300B
Ext. DTR
Int. Dark Char
FINALLY BOOSTED!!!
Thanks allot!
Does anyone use an old Sct 96xx livewire? I have one that came with the car but I doubt they are supported anymore. Does anyone know if it would still work for my custom tune on the dyno?
Also does anyone have the diameter this of main barb? I'm not with the engine at the moment
Last edited by minimarine09; 12-30-2017 at 10:06 AM.
had to wait until some money came in, but made a good bit of progress.
ok sooo
got the engine all together, a dropped her in!
had to cut the lip of the water pump pulley down a bit in order to fit a belt between it and the IW damper
started putting the coolant system in after a bunch of misc. stuff on the motor. my pass. side coolant sensor hits the supercharger. also the 90 degrees that comes with the on3 kit doesnt clear either. so i drove around and found double female, and double male fittings for -10 AN to lift it higher to clear everything. also got a 90 degree 3/8 NPT fitting so i can mount the sensor vertically.
i know i could have just ran 45 degree fitting and clear, but i dont like the way one side the hose is flat, and one is at an upward angle, if this set up bring it too high then ill just go for the 45.
also, the old upper coolant elbow was promoted to new lower hose connector. hopefully it doesnt get in the way of the intercooler pipes.
...
METHHHHHH
Last edited by minimarine09; 12-30-2017 at 10:17 AM.
Where is the aux. idler between the alternator and PS pump? You definitely need that. And Mach 1 covers/tensioners are identical to the Marauder.
i have it, just need to throw it on, need to find a bolt first. i may need a slightly longer belt if im not able to stretch it with the extra pulley. idk, i just called tech support at thump racing and told me that, so i just listened. feels much more snug than the one it came with.
There are currently 1 users browsing this thread. (0 members and 1 guests)