Need some info on what I need to do to have a functioning egr system with my eaton swap thx guys
Need some info on what I need to do to have a functioning egr system with my eaton swap thx guys
What egr setup can I run with on my eaton swap and I don't want to eliminate it all input appreciated thx kevin
You need to use MM egr top needs to be rotated custom made tube. I think
better to do a burn-out than fade away
There's an adapter between the egr tube nut and the header itself. That needs to be cut and an extension welded in. I used about an 1"+ of steel pipe. Mock up then measure for what you'll need.
NOTE: I have FRPP shorty headers.
Last edited by RacerX; 11-29-2013 at 06:29 AM.
11.931 @ 116.33 (MT ET Streets)
12.073 @ 118.43 (Nitto 555)
I love the smell of Nitromethane and rubber in the morning!
Drag racers prayer:
As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen
Lift up all the metal tabs carefully. And slowly rotate the EGR until its in the position as pictured.
You will need to modify the EGR tube.
As you can see. Mine fits perfect.
Sent from The White House on taxpayers dimes.
DTR + 4.10's + Eaton swap = Wreeeeeeeeeeeeeeedom
I'm about to install a EGR setup on a eaton swapped marauder tomorrow. We are going to attempt to use stainless steel flex gas line as a egr tube and make it all work. Turns out that turning off the EGR in the tune will make it fail NJ inspection.
Details to follow after this adventure.
2003 MERCURY MARAUDER 300A
Build Date
5/31/02
Sequence#
#363 of 7839 Black Marauders
Dyno tested power
450 RWHP & 405 RWTQ on 93 octane
Best 1/4 mile time to date
12.456@109mph
Visit my Garage
Blackened300a's Garage
Someone else on here used the flex line and it worked great. I found it when looking for solutions myself on here after I failed NH inspection without the EGR hooked up. That was #2 if my current solution with the Shorty Headers didn't work.
11.931 @ 116.33 (MT ET Streets)
12.073 @ 118.43 (Nitto 555)
I love the smell of Nitromethane and rubber in the morning!
Drag racers prayer:
As I lay rubber down the street, I pray for traction I can keep, but if I spin and begin to slide, please dear God protect my ride." -Amen
Joe, why didn't you do the EGR delete? Does turning it off make it fail Illinois inspection?
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
I cannot understand why lots of folks want to "delete" the EGR system since it has benefits??
It actually lowers combustion temps and DOES NOT OPERATE at WOT so what's the problem.....it does not reduce performance??
Delete it and deal with higher combustion temps, part throttle detonation and possibly engine destruction unless you tune it well......most of us don't know how to including me!!
Keep it hooked up and functional.......pass emissions and be HAPPY.....HAPPY.....HAPPY!!
No Marauder
I struggled with this during my eaton swap. I did some googling and found a lot of people that tried it (not marauder specific). The thing that sacred me was it doesn't last very long. Must people said it only last about 6 months. That tube is subjected to a lot of heat. Good luck and I hope it works because that was my biggest challange.
03 SB 300B
Eaton Swap Tuned by Fast Specialities
Trans rebuilt by Darin at BC Automotive with a Triple Disc 11in Circle D TC. Tuned by Zack. The man that made my Marauder fun again.
4.10 gears with Cobra clutches. No more one wheel peel
Metco Drive Shaft Loop.
Next bigger brakes!!!!
There are currently 1 users browsing this thread. (0 members and 1 guests)