Just bought some Stainless Works headers and was wondering if I should install header wrap to keep the heat down? Curious what others who have installed headers on the marauder have done
Just bought some Stainless Works headers and was wondering if I should install header wrap to keep the heat down? Curious what others who have installed headers on the marauder have done
Got my Kooks thermal coated from HPC....back in 2004.
Last edited by Joe Walsh; 07-28-2018 at 07:56 AM.
2020 Ford Ranger STX DFI Turbo 2.3L 10 speed Auto
2017 Ford Fusion Sport DFI Twin Turbo 2.7L V6 6 speed Auto (14.000 ET bone stock in 82 degree heat)
1985 Mustang GT 5.0 Hatchback 4bbl 5 speed manual (525 HP 363 Dart block/AFR heads with Magnum 6 speed in the works)
1984 Mustang GT 2.3 Turbo Convertible FI. 5 speed manual
1966 427 Cobra (ERA) 468 all Aluminum FE 2x4bbl 5 speed manual
SOLD : 2003 Mercury Marauder FI. 4 speed Auto
w/Crower Cams & Springs, +1mm SS valves, mild port job on the cylinder heads.
Extrude honed intake w/PHP spacer.
Kooks Headers w/2.5" High Flow Cats & X-Pipe, Magnaflow mufflers, OEM tailpipes w/Megs Tips
B&M Trans cooler w/fan, Level 10 Shift Kit, Art Carr Hughes Deep Sump Trans Pan,
SVO Rearend Girdle, Redline Gear lube; OEM 3.55s
'Real Gauges' + matching Trans Temp, Oil Temp, Water Temp, Fuel Pressure, Vacuum/Boost Gauge
Built: 10/15/02 Bought: 12/16/02 Sold: 10/15/18
Get them ceramic Coated. Mine still look like this a year later.
Sent from my iPhone using Tapatalk Pro
Save your money the header wrap! that stuff is garbage that holds in moisture , dirt , oil and anything else that comes in contact with it.
04 MERCURY MARAUDER build date:02/11/04ITS ALIVE !!!!!!!!
STAY TUNED!!!!!!!!!!
**WHIPPLE 4.0L CRUSHER!**0000 (FOR NOW) RWHP
VISIT MY GARAGE FOR A FULL LIST OF MODS
Wow. Well there’s no doubt your headers look better than ones I’ve seen that have been covered with header wrap.
Do you want the heat dispersed over a large area or concentrated to a smaller area?
1/4 Mile Time 11.542 @ 121.19 MPH
195,000 Miles & 275+ Runs Down the 1,320’
541.57 RWHP & 476.64 RWTQ on DynoJet
Tuned by Aric at Injected Engineering
Vortech Super Charger V-2 “T” Trim, 19 PSI
8 Rib Belt, Innovators West 10% Overdrive Dampner
Air to Air Intercooler, Mini-race Bypass
Ford Cobra Remanufactured Long Block
Snow Performance Water-Methanol Injection
Kooks Headers & X Pipe
GT MAF, 60lb injectors, Dash 8, Aero Rails, Twin Ford GT Pumps,
Kinsler Fuel Filter, Kenne Bell Boost-A-Pump
Monroe Sensatrac, Metco Control Arms, Addco Rear Sway Bar
31 Ford Spline Axles & Detroit Truetrac, 4:10 Ford Racing Gears
Dynotech MMC Driveshaft
A-1 Performance Trans, Forced Tailshaft Lube, Carbon Clutches
3,500 RPM Stall Precision Industries Torque Converter
B&M Deep Finned Trans Pan
AeroForce Scan Gauges , Auto Meter Oil, Fuel & Boost Gauges
Kenny Brown Dead Pedal, 35% Tint, Silver Star Head Lights
AutoPage Alarm RS-727LCD, Boston Acoustic NX87
I just wrapped the starter with a heat blanket. I also removed all insulation off the firewall and the a/c box and painted the firewall and undercarriage black. The insulation on the firewall was hanging down onto the exhaust and the a/c was well, just ugly. I pulled the interior and added dynamat type sound proofing and heat shield material to the firewall and floor and that took away all the added noise and heat created from the headers. The a/c is still as ice cold as ever with the fugly insulation removed for four years now.
My headers still look great after years of use but it rarely ever sees moisture.
If your only interested in heat and looks, ceramic coating them in and out is your best bet. I just didn’t have the finances at the time and wanted to focus more on cleaning up the engine bay and undercarriage and sound proofing.
Sent from my iPhone using Tapatalk
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
A BIG +1 on the starter heat wrap/blanket!
I didn't like the idea of a bunch of hot header tubes surrounding the starter motor.
You can see mine in the picture from my previous post.
It was a lot neater looking when I first installed it...but it's been removed and re-installed multiple times and not as clean an install as before.
2020 Ford Ranger STX DFI Turbo 2.3L 10 speed Auto
2017 Ford Fusion Sport DFI Twin Turbo 2.7L V6 6 speed Auto (14.000 ET bone stock in 82 degree heat)
1985 Mustang GT 5.0 Hatchback 4bbl 5 speed manual (525 HP 363 Dart block/AFR heads with Magnum 6 speed in the works)
1984 Mustang GT 2.3 Turbo Convertible FI. 5 speed manual
1966 427 Cobra (ERA) 468 all Aluminum FE 2x4bbl 5 speed manual
SOLD : 2003 Mercury Marauder FI. 4 speed Auto
w/Crower Cams & Springs, +1mm SS valves, mild port job on the cylinder heads.
Extrude honed intake w/PHP spacer.
Kooks Headers w/2.5" High Flow Cats & X-Pipe, Magnaflow mufflers, OEM tailpipes w/Megs Tips
B&M Trans cooler w/fan, Level 10 Shift Kit, Art Carr Hughes Deep Sump Trans Pan,
SVO Rearend Girdle, Redline Gear lube; OEM 3.55s
'Real Gauges' + matching Trans Temp, Oil Temp, Water Temp, Fuel Pressure, Vacuum/Boost Gauge
Built: 10/15/02 Bought: 12/16/02 Sold: 10/15/18
Woooo hooo those are purdy!!!!!!!!! Car porn.
'04 Silver Marauder w/ sunroof - HID lighting, JL Audio / Eclipse DVD/NAV/iPod/camera, 4.10's, 2" drop, Progard Bumper Baffle, Delete tips, Billet Pedals, BC4E dead pedal, Lidio Tune, Mach1 chin spoiler, K&N CAI, TCE lines, Super40's, tinted tails, SS Inserts, Heinous Control Arms, Real oil gauge, lighted door handles. Currently installing Eaton M112.
2004 Mercury Marauder
Born March 2004, adopted October 2005. Sold January 2012, adopted AGAIN January 2016
2,187 of 3,214
997 in Silver Birch
448 with light flint interior
304 with heated seats
336 with sunroof
Another +1 on the starter wrap. I added mine because I want my starter to last as long as possible because getting those headers off is a nightmare. I'd rather put on 20 superchargers than ever touch the headers again.
+1 on coating vs wrap as well.
"Come to me, Superman! I defy you! Come and kneel before Zod! Zod! "
If you wrap Stainless Works headers your warranty will be void. Header wrap is horrible for the headers, holds too much moisture, they will rot out..
#2941 300A
4.10's, carbon clutches
Marty O Tune
Curless Cure
Widened Wheels
Dead Pedal
Eaton Swapped
Bar tender and maker of:
Christmas in a cup
The "Bucket of South Haven Iced Tea"
One Legged Lesbian Kickboxer
Cocka Two
Ok cool. Header wrap not good. I hate that itchy stuff anyway
There are currently 1 users browsing this thread. (0 members and 1 guests)