How difficult is it to remove the Trunk Lining?
Is it held just by the plastic rivets?
How difficult is it to remove the Trunk Lining?
Is it held just by the plastic rivets?
1/4 Mile Time 11.542 @ 121.19 MPH
195,000 Miles & 275+ Runs Down the 1,320’
541.57 RWHP & 476.64 RWTQ on DynoJet
Tuned by Aric at Injected Engineering
Vortech Super Charger V-2 “T” Trim, 19 PSI
8 Rib Belt, Innovators West 10% Overdrive Dampner
Air to Air Intercooler, Mini-race Bypass
Ford Cobra Remanufactured Long Block
Snow Performance Water-Methanol Injection
Kooks Headers & X Pipe
GT MAF, 60lb injectors, Dash 8, Aero Rails, Twin Ford GT Pumps,
Kinsler Fuel Filter, Kenne Bell Boost-A-Pump
Monroe Sensatrac, Metco Control Arms, Addco Rear Sway Bar
31 Ford Spline Axles & Detroit Truetrac, 4:10 Ford Racing Gears
Dynotech MMC Driveshaft
A-1 Performance Trans, Forced Tailshaft Lube, Carbon Clutches
3,500 RPM Stall Precision Industries Torque Converter
B&M Deep Finned Trans Pan
AeroForce Scan Gauges , Auto Meter Oil, Fuel & Boost Gauges
Kenny Brown Dead Pedal, 35% Tint, Silver Star Head Lights
AutoPage Alarm RS-727LCD, Boston Acoustic NX87
Yes. Very easy
its in two pieces, very easy to remove. the sides near the wheel wells is attached with velcro. it tends to pull off the metal and just stay stuck to the lining. I think there are a few push pins as well.
"Come to me, Superman! I defy you! Come and kneel before Zod! Zod! "
Very easy. Five minutes or less. When I first bought mine, I removed the whole thing to give it thorough cleaning. A couple of fasteners and some Velcro. Comes right out. Just be careful not to break the fasteners when removing, unless you have a couple of spares hanging around. That's it.
Thanks to everyone for replying!
1/4 Mile Time 11.542 @ 121.19 MPH
195,000 Miles & 275+ Runs Down the 1,320’
541.57 RWHP & 476.64 RWTQ on DynoJet
Tuned by Aric at Injected Engineering
Vortech Super Charger V-2 “T” Trim, 19 PSI
8 Rib Belt, Innovators West 10% Overdrive Dampner
Air to Air Intercooler, Mini-race Bypass
Ford Cobra Remanufactured Long Block
Snow Performance Water-Methanol Injection
Kooks Headers & X Pipe
GT MAF, 60lb injectors, Dash 8, Aero Rails, Twin Ford GT Pumps,
Kinsler Fuel Filter, Kenne Bell Boost-A-Pump
Monroe Sensatrac, Metco Control Arms, Addco Rear Sway Bar
31 Ford Spline Axles & Detroit Truetrac, 4:10 Ford Racing Gears
Dynotech MMC Driveshaft
A-1 Performance Trans, Forced Tailshaft Lube, Carbon Clutches
3,500 RPM Stall Precision Industries Torque Converter
B&M Deep Finned Trans Pan
AeroForce Scan Gauges , Auto Meter Oil, Fuel & Boost Gauges
Kenny Brown Dead Pedal, 35% Tint, Silver Star Head Lights
AutoPage Alarm RS-727LCD, Boston Acoustic NX87
There are currently 1 users browsing this thread. (0 members and 1 guests)